Merge pull request #241 from nandra/sumo-backports

Add kernel build fix + wifi support to sumo

README.md

@@ -31,13 +31,7 @@ If you want to switch back to sunxi versions for some reasons (no device tree av
 
 If you already have built the mainline versions it might be necessary to reset the build directories with:
 
-	bitbake -c clean linux
-	bitbake -c clean u-boot
-
-Also, older kernel versions such as this don't build successfully with any gcc version 5.0 or newer. Since gcc-5.2 is the current
-default compiler on master, if you wish to build this kernel with master you'll need to add the following to your conf/local.conf:
-
-	GCCVERSION = "4.9%"
+	bitbake -c clean virtual/kernel virtual/bootloader
 
 Performance
 ===========

classes/sdcard_image-sunxi.bbclass

@@ -7,8 +7,8 @@ inherit image_types
 # The disk layout used is:
 #
 #    0                      -> 8*1024                           - reserverd
-#    8*1024                 -> 32*1024                          - 
-#    32*1024                -> 2048*1024                        - 
+#    8*1024                 ->                                  - arm combined spl/u-boot or aarch64 spl
+#    40*1024                ->                                  - aarch64 u-boot
 #    2048*1024              -> BOOT_SPACE                       - bootloader and kernel
 #
 #
@@ -20,29 +20,25 @@ IMAGE_TYPEDEP_sunxi-sdimg = "${SDIMG_ROOTFS_TYPE}"
 BOOTDD_VOLUME_ID ?= "${MACHINE}"
 
 # Boot partition size [in KiB]
-BOOT_SPACE ?= "20480"
+BOOT_SPACE ?= "40960"
 
 # First partition begin at sector 2048 : 2048*1024 = 2097152
 IMAGE_ROOTFS_ALIGNMENT = "2048"
 
-# Use an uncompressed ext3 by default as rootfs
+# Use an uncompressed ext4 by default as rootfs
 SDIMG_ROOTFS_TYPE ?= "ext4"
-SDIMG_ROOTFS = "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.${SDIMG_ROOTFS_TYPE}"
+SDIMG_ROOTFS = "${IMGDEPLOYDIR}/${IMAGE_NAME}.rootfs.${SDIMG_ROOTFS_TYPE}"
 
-IMAGE_DEPENDS_sunxi-sdimg += " \
-			parted-native \
-			mtools-native \
-			dosfstools-native \
-			virtual/kernel \
-			virtual/bootloader \
+do_image_sunxi_sdimg[depends] += " \
+			parted-native:do_populate_sysroot \
+			mtools-native:do_populate_sysroot \
+			dosfstools-native:do_populate_sysroot \
+			virtual/kernel:do_deploy \
+			virtual/bootloader:do_deploy \
 			"
 
-rootfs[depends] += "virtual/kernel:do_deploy"
-
 # SD card image name
-SDIMG = "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.sunxi-sdimg"
-
-IMAGEDATESTAMP = "${@time.strftime('%Y.%m.%d',time.gmtime())}"
+SDIMG = "${IMGDEPLOYDIR}/${IMAGE_NAME}.rootfs.sunxi-sdimg"
 
 IMAGE_CMD_sunxi-sdimg () {
 
@@ -68,17 +64,23 @@ IMAGE_CMD_sunxi-sdimg () {
 	rm -f ${WORKDIR}/boot.img
 	mkfs.vfat -n "${BOOTDD_VOLUME_ID}" -S 512 -C ${WORKDIR}/boot.img $BOOT_BLOCKS
 
-	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin ::uImage
+	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin ::${KERNEL_IMAGETYPE}
 
 	# Copy device tree file
 	if test -n "${KERNEL_DEVICETREE}"; then
 		for DTS_FILE in ${KERNEL_DEVICETREE}; do
 			DTS_BASE_NAME=`basename ${DTS_FILE} | awk -F "." '{print $1}'`
-			if [ -e "${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb" ]; then
-				kernel_bin="`readlink ${KERNEL_IMAGETYPE}-${MACHINE}.bin`"
-				kernel_bin_for_dtb="`readlink ${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb | sed "s,$DTS_BASE_NAME,${MACHINE},g;s,\.dtb$,.bin,g"`"
+			DTS_DIR_NAME=`dirname ${DTS_FILE}`
+			if [ -e ${DEPLOY_DIR_IMAGE}/"${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb" ]; then
+
+				if [ ${DTS_FILE} != ${DTS_BASE_NAME}.dtb ]; then
+					mmd -i ${WORKDIR}/boot.img ::/${DTS_DIR_NAME}
+				fi
+
+				kernel_bin="`readlink ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin`"
+				kernel_bin_for_dtb="`readlink ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb | sed "s,$DTS_BASE_NAME,${MACHINE},g;s,\.dtb$,.bin,g"`"
 				if [ $kernel_bin = $kernel_bin_for_dtb ]; then
-					mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb ::/${DTS_BASE_NAME}.dtb
+					mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb ::/${DTS_FILE}
 				fi
 			fi
 		done
@@ -95,8 +97,8 @@ IMAGE_CMD_sunxi-sdimg () {
 
 
 	# Add stamp file
-	echo "${IMAGE_NAME}-${IMAGEDATESTAMP}" > ${WORKDIR}/image-version-info
-	mcopy -i ${WORKDIR}/boot.img -v ${WORKDIR}//image-version-info ::
+	echo "${IMAGE_NAME}" > ${WORKDIR}/image-version-info
+	mcopy -i ${WORKDIR}/boot.img -v ${WORKDIR}/image-version-info ::
 
 	# Burn Partitions
 	dd if=${WORKDIR}/boot.img of=${SDIMG} conv=notrunc seek=1 bs=$(expr ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
@@ -108,7 +110,15 @@ IMAGE_CMD_sunxi-sdimg () {
 		dd if=${SDIMG_ROOTFS} of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
 	fi
 
-	#write u-boot and spl at the beginint of sdcard in one shot
-	dd if=${DEPLOY_DIR_IMAGE}/u-boot-sunxi-with-spl.bin of=${SDIMG} bs=1024 seek=8 conv=notrunc
-
+	# write u-boot-spl at the begining of sdcard in one shot
+	SPL_FILE=$(basename ${SPL_BINARY})
+	dd if=${DEPLOY_DIR_IMAGE}/${SPL_FILE} of=${SDIMG} bs=1024 seek=8 conv=notrunc
+}
+
+# write uboot.itb for arm64 boards
+IMAGE_CMD_sunxi-sdimg_append_sun50i () {
+	if [ -e "${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY}" ]
+	then
+		dd if=${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY} of=${SDIMG} bs=1024 seek=40 conv=notrunc
+	fi
 }

conf/layer.conf

@@ -7,3 +7,4 @@ BBFILES += "${LAYERDIR}/recipes*/*/*.bb ${LAYERDIR}/recipes*/*/*.bbappend"
 BBFILE_COLLECTIONS += "meta-sunxi"
 BBFILE_PATTERN_meta-sunxi := "^${LAYERDIR}/"
 BBFILE_PRIORITY_meta-sunxi = "10"
+LAYERSERIES_COMPAT_meta-sunxi = "morty pyro rocko sumo thud"

conf/machine/include/sun50i.inc

@@ -0,0 +1,4 @@
+require conf/machine/include/sunxi64.inc
+require conf/machine/include/arm/arch-armv8.inc
+
+SOC_FAMILY = "sun50i"

conf/machine/include/sun8i.inc

@@ -0,0 +1,5 @@
+require conf/machine/include/sunxi.inc
+require conf/machine/include/sunxi-mali.inc
+require conf/machine/include/tune-cortexa7.inc
+
+SOC_FAMILY = "sun8i"

conf/machine/include/sunxi.inc

@@ -12,7 +12,7 @@ XSERVER = "xserver-xorg \
            xf86-input-mouse \
            xf86-input-keyboard"
 
-PREFERRED_PROVIDER_virtual/kernel ?= "linux"
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
 PREFERRED_PROVIDER_u-boot ?= "u-boot"
 PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"
 
@@ -28,5 +28,7 @@ UBOOT_LOCALVERSION = "-g${@d.getVar('SRCPV', True).partition('+')[2][0:7]}"
 UBOOT_ENTRYPOINT ?= "0x40008000"
 UBOOT_LOADADDRESS ?= "0x400080OB00"
 
+SPL_BINARY ?= "u-boot-sunxi-with-spl.bin"
+
 SERIAL_CONSOLE ?= "115200 ttyS0"
 MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"

conf/machine/include/sunxi64.inc

@@ -0,0 +1,24 @@
+SOC_FAMILY ??= ""
+include conf/machine/include/soc-family.inc
+
+PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
+PREFERRED_PROVIDER_u-boot ?= "u-boot"
+PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"
+
+KERNEL_IMAGETYPE ?= "Image"
+
+IMAGE_CLASSES += "sdcard_image-sunxi"
+IMAGE_FSTYPES += "ext4 tar.gz sunxi-sdimg"
+
+MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"
+
+UBOOT_LOCALVERSION = "-g${@d.getVar('SRCPV', True).partition('+')[2][0:7]}"
+
+UBOOT_ENTRYPOINT ?= "0x40008000"
+UBOOT_LOADADDRESS ?= "0x400080OB00"
+
+UBOOT_BINARY ?= "u-boot.itb"
+SPL_BINARY ?= "spl/sunxi-spl.bin"
+
+SERIAL_CONSOLE ?= "115200 ttyS0"
+MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"

conf/machine/nanopi-neo-air.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: nanopi-neo-air
+#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo Air, based
+# on the Allwinner H3 CPU.
+
+require conf/machine/include/sun8i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo-air.dtb"
+UBOOT_MACHINE = "nanopi_neo_air_defconfig"

conf/machine/nanopi-neo-plus2.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: nanopi-neo-plus2
+#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo Plus2, based
+# on the Allwinner H5 SoC.
+
+require conf/machine/include/sun50i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h5-nanopi-neo-plus2.dtb"
+UBOOT_MACHINE = "nanopi_neo_plus2_defconfig"

conf/machine/nanopi-neo.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: nanopi-neo
+#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo, based on the Allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo.dtb"
+UBOOT_MACHINE = "nanopi_neo_defconfig"
+

conf/machine/nanopi-neo2.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: nanopi-neo2
+#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo 2, based on
+# the Allwinner H5 SoC.
+
+require conf/machine/include/sun50i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h5-nanopi-neo2.dtb"
+UBOOT_MACHINE = "nanopi_neo2_defconfig"

conf/machine/olinuxino-a20lime2-emmc.conf

@@ -0,0 +1,10 @@
+#@TYPE: Machine
+#@NAME: Olimex A20-OLinuXino Lime2 Board with 4GB eMMC
+#@DESCRIPTION: Machine configuration for the Olimex A20-OLinuXino Lime2 Board with 4GB eMMC, based on Allwinner A20 CPU
+#https://github.com/OLIMEX/OLINUXINO
+
+require conf/machine/include/sun7i.inc
+
+KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime2-emmc.dtb"
+UBOOT_MACHINE = "A20-OLinuXino-Lime2-eMMC_config"
+SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime2.fex"

conf/machine/olinuxino-a20som.conf

@@ -5,5 +5,6 @@
 
 require conf/machine/include/sun7i.inc
 
-UBOOT_MACHINE = "Olimex_A20-SOM_config"
-SUNXI_FEX_FILE = "sys_config/a20/olimex_a20_som.fex"
+KERNEL_DEVICETREE = "sun7i-a20-olimex-som-evb.dtb"
+UBOOT_MACHINE = "A20-Olimex-SOM-EVB_config"
+SUNXI_FEX_FILE = "sys_config/a20/olimex_a20_som.fex"

conf/machine/orange-pi-one.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: orange-pi-one
+#@DESCRIPTION: Machine configuration for the orange-pi-one, base on allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "sun8i-h3-orangepi-one.dtb"
+UBOOT_MACHINE = "orangepi_one_defconfig"
+

conf/machine/orange-pi-pc-plus.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: orange-pi-pc-plus
+#@DESCRIPTION: Machine configuration for the orange-pi-pc-plus, base on allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc-plus.dtb"
+UBOOT_MACHINE = "orangepi_pc_plus_defconfig"
+

conf/machine/orange-pi-pc.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: orange-pi-one
+#@DESCRIPTION: Machine configuration for the orange-pi-one, base on allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc.dtb"
+UBOOT_MACHINE = "orangepi_pc_defconfig"
+

conf/machine/orange-pi-zero-plus2.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: orange-pi-zero-plus2
+#@DESCRIPTION: Machine configuration for the orange-pi-zero-plus2, base on Allwinner H5 CPU
+
+
+require conf/machine/include/sun50i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h5-orangepi-zero-plus2.dtb"
+UBOOT_MACHINE = "orangepi_zero_plus2_defconfig"

conf/machine/orange-pi-zero.conf

@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: orange-pi-one
+#@DESCRIPTION: Machine configuration for the orange-pi-one, base on allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
+KERNEL_DEVICETREE = "sun8i-h2-plus-orangepi-zero.dtb"
+UBOOT_MACHINE = "orangepi_zero_defconfig"
+

conf/machine/pcduino.conf

@@ -4,6 +4,8 @@
 
 require conf/machine/include/sun4i.inc
 
+PREFERRED_VERSION_u-boot = "v2018.03%"
+
 KERNEL_DEVICETREE = "sun4i-a10-pcduino.dtb"
 UBOOT_MACHINE = "Linksprite_pcDuino_defconfig"
 SUNXI_FEX_FILE = "sys_config/a10/pcduino.fex"

recipes-bsp/atf/atf-sunxi_git.bb

@@ -0,0 +1,27 @@
+DESCRIPTION = "ARM Trusted Firmware Allwinner"
+LICENSE = "BSD"
+LIC_FILES_CHKSUM = "file://license.md;md5=829bdeb34c1d9044f393d5a16c068371"
+
+SRC_URI = "git://github.com/apritzel/arm-trusted-firmware;nobranch=1"
+SRCREV = "aa75c8da415158a94b82a430b2b40000778e851f"
+
+S = "${WORKDIR}/git"
+B = "${WORKDIR}/build"
+
+COMPATIBLE_MACHINE = "(sun50i)"
+
+PLATFORM_sun50i = "sun50iw1p1"
+
+LDFLAGS[unexport] = "1"
+
+do_compile() {
+    oe_runmake -C ${S} BUILD_BASE=${B} \
+      CROSS_COMPILE=${TARGET_PREFIX} \
+      PLAT=${PLATFORM} \
+      bl31 \
+      all
+}
+
+do_install() {
+    install -D -p -m 0644 ${B}/${PLATFORM}/release/bl31.bin ${DEPLOY_DIR_IMAGE}/bl31.bin
+}

recipes-bsp/u-boot/files/0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch

@@ -0,0 +1,26 @@
+From f4a77da23b3890b53efab6a927cbe99b76ef3b26 Mon Sep 17 00:00:00 2001
+From: Florin Sarbu <florin@resin.io>
+Date: Wed, 12 Sep 2018 14:22:49 +0200
+Subject: [PATCH] nanopi_neo_air_defconfig: Enable eMMC support
+
+Upstream-status: Pending
+Signed-off-by: Florin Sarbu <florin@resin.io>
+---
+ configs/nanopi_neo_air_defconfig | 1 +
+ 1 file changed, 1 insertion(+)
+
+diff --git a/configs/nanopi_neo_air_defconfig b/configs/nanopi_neo_air_defconfig
+index ca9c2dd..74ce044 100644
+--- a/configs/nanopi_neo_air_defconfig
++++ b/configs/nanopi_neo_air_defconfig
+@@ -10,6 +10,7 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-neo-air"
+ # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+ CONFIG_CONSOLE_MUX=y
+ CONFIG_SPL=y
++CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+ # CONFIG_CMD_FLASH is not set
+ # CONFIG_SPL_DOS_PARTITION is not set
+ # CONFIG_SPL_ISO_PARTITION is not set
+-- 
+2.7.4
+

recipes-bsp/u-boot/files/aarch64/boot.cmd

@@ -0,0 +1,11 @@
+# Default to (primary) SD
+rootdev=mmcblk0p2
+if itest.b *0x28 == 0x02 ; then
+	# U-Boot loaded from eMMC or secondary SD so use it for rootfs too
+	echo "U-boot loaded from eMMC or secondary SD"
+	rootdev=mmcblk1p2
+fi
+setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
+load mmc 0:1 ${fdt_addr_r} ${fdtfile}
+load mmc 0:1 ${kernel_addr_r} Image
+booti ${kernel_addr_r} - ${fdt_addr_r}

recipes-bsp/u-boot/files/arm/boot.cmd

@@ -1,4 +1,11 @@
-setenv bootargs console=${console} console=tty1 root=/dev/mmcblk0p2 rootwait panic=10 ${extra}
+# Default to (primary) SD
+rootdev=mmcblk0p2
+if itest.b *0x28 == 0x02 ; then
+	# U-Boot loaded from eMMC or secondary SD so use it for rootfs too
+	echo "U-boot loaded from eMMC or secondary SD"
+	rootdev=mmcblk1p2
+fi
+setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
 load mmc 0:1 ${fdt_addr_r} ${fdtfile} || load mmc 0:1 ${fdt_addr_r} boot/${fdtfile}
 load mmc 0:1 ${kernel_addr_r} zImage || load mmc 0:1 ${kernel_addr_r} boot/zImage || load mmc 0:1 ${kernel_addr_r} uImage || load mmc 0:1 ${kernel_addr_r} boot/uImage
 bootz ${kernel_addr_r} - ${fdt_addr_r} || bootm ${kernel_addr_r} - ${fdt_addr_r}

recipes-bsp/u-boot/files/u-boot-pylibfdt-native-build.patch

@@ -0,0 +1,16 @@
+diff --git a/scripts/dtc/pylibfdt/Makefile b/scripts/dtc/pylibfdt/Makefile
+index 01d5e0ffe3..2b2dfe0bd9 100644
+--- a/scripts/dtc/pylibfdt/Makefile
++++ b/scripts/dtc/pylibfdt/Makefile
+@@ -15,6 +15,8 @@ PYLIBFDT_srcs = $(addprefix $(LIBFDT_srcdir)/,$(LIBFDT_SRCS)) \
+ 
+ quiet_cmd_pymod = PYMOD   $@
+       cmd_pymod = unset CC; unset CROSS_COMPILE; unset CFLAGS;\
++		CC="$(HOSTCC)" \
++		LDSHARED="$(HOSTLDSHARED)" \
+ 		LDFLAGS="$(HOSTLDFLAGS)" \
+ 		VERSION="u-boot-$(UBOOTVERSION)" \
+ 		CPPFLAGS="$(HOSTCFLAGS) -I$(LIBFDT_srcdir)" OBJDIR=$(obj) \
+-- 
+2.11.0
+

recipes-bsp/u-boot/u-boot-sunxi.bb

@@ -21,6 +21,7 @@ UBOOT_MACHINE_meleg = "Mele_A1000G_config"
 SRC_URI = " \
 	git://github.com/linux-sunxi/u-boot-sunxi.git;protocol=git;branch=sunxi \
 	file://0002-gcc5-fixes.patch \
+	file://0003-gcc6-fixes.patch \
 	"
 
 PE = "1"

recipes-bsp/u-boot/u-boot-sunxi/0003-gcc6-fixes.patch

@@ -1,8 +1,7 @@
-Index: git/include/linux/compiler-gcc5.h
-===================================================================
---- git/include/linux/compiler-gcc5.h    2015-09-19 20:11:27.999423338 +0200
-+++ git/include/linux/compiler-gcc5.h    2015-09-23 10:26:05.000000000 +0200
-@@ -0,0 +1,66 @@
+diff -urN git-ORIG/include/linux/compiler-gcc6.h git/include/linux/compiler-gcc6.h
+--- git-ORIG/include/linux/compiler-gcc6.h	1969-12-31 19:00:00.000000000 -0500
++++ git/include/linux/compiler-gcc6.h	2017-04-09 19:50:16.920945874 -0400
+@@ -0,0 +1,65 @@
 +#ifndef __LINUX_COMPILER_H
 +#error "Please don't include <linux/compiler-gcc5.h> directly, include <linux/compiler.h> instead."
 +#endif
@@ -58,7 +57,6 @@ Index: git/include/linux/compiler-gcc5.h
 + *   http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
 + *
 + * Work it around via a compiler barrier quirk suggested by Jakub Jelinek.
-+ * Fixed in GCC 4.8.2 and later versions.
 + *
 + * (asm goto is automatically volatile - the naming reflects this.)
 + */

recipes-bsp/u-boot/u-boot_2016.03.bb

@@ -1,44 +0,0 @@
-DESCRIPTION="Upstream's U-boot configured for sunxi devices"
-
-require recipes-bsp/u-boot/u-boot.inc
-
-DEPENDS += "dtc-native"
-
-LICENSE = "GPLv2"
-
-LIC_FILES_CHKSUM = "\
-file://Licenses/Exceptions;md5=338a7cb1e52d0d1951f83e15319a3fe7 \
-file://Licenses/bsd-2-clause.txt;md5=6a31f076f5773aabd8ff86191ad6fdd5 \
-file://Licenses/bsd-3-clause.txt;md5=4a1190eac56a9db675d58ebe86eaf50c \
-file://Licenses/eCos-2.0.txt;md5=b338cb12196b5175acd3aa63b0a0805c \
-file://Licenses/gpl-2.0.txt;md5=b234ee4d69f5fce4486a80fdaf4a4263 \
-file://Licenses/ibm-pibs.txt;md5=c49502a55e35e0a8a1dc271d944d6dba \
-file://Licenses/isc.txt;md5=ec65f921308235311f34b79d844587eb \
-file://Licenses/lgpl-2.0.txt;md5=5f30f0716dfdd0d91eb439ebec522ec2 \
-file://Licenses/lgpl-2.1.txt;md5=4fbd65380cdd255951079008b364516c \
-file://Licenses/x11.txt;md5=b46f176c847b8742db02126fb8af92e2 \
-"
-
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i)"
-
-DEFAULT_PREFERENCE_sun4i="1"
-DEFAULT_PREFERENCE_sun5i="1"
-DEFAULT_PREFERENCE_sun7i="1"
-
-SRC_URI = "git://git.denx.de/u-boot.git;branch=master \
-           file://boot.cmd"
-
-SRCREV = "df61a74e6845ec9bdcdd48d2aff5e9c2c6debeaa"
-
-PV = "v2016.03${SRCPV}"
-
-PE = "1"
-
-SPL_BINARY="u-boot-sunxi-with-spl.bin"
-
-UBOOT_ENV_SUFFIX = "scr"
-UBOOT_ENV = "boot"
-
-do_compile_append() {
-    ${S}/tools/mkimage -C none -A arm -T script -d ${WORKDIR}/boot.cmd ${WORKDIR}/${UBOOT_ENV_BINARY}
-}

recipes-bsp/u-boot/u-boot_2018.03.bb

@@ -0,0 +1,42 @@
+DESCRIPTION="Upstream's U-boot configured for sunxi devices"
+
+require recipes-bsp/u-boot/u-boot.inc
+
+DEPENDS += " bc-native dtc-native swig-native python3-native "
+DEPENDS_append_sun50i = " atf-sunxi "
+
+LICENSE = "GPLv2+"
+LIC_FILES_CHKSUM = "file://Licenses/README;md5=a2c678cfd4a4d97135585cad908541c6"
+
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
+
+DEFAULT_PREFERENCE_sun4i="1"
+DEFAULT_PREFERENCE_sun5i="1"
+DEFAULT_PREFERENCE_sun7i="1"
+DEFAULT_PREFERENCE_sun8i="1"
+DEFAULT_PREFERENCE_sun50i="1"
+
+SRC_URI = "git://git.denx.de/u-boot.git;branch=master \
+           file://u-boot-pylibfdt-native-build.patch \
+           file://0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch \
+           file://boot.cmd \
+           "
+
+SRCREV = "f95ab1fb6e37f0601f397091bb011edf7a98b890"
+
+PV = "v2018.03+git${SRCPV}"
+PE = "2"
+
+S = "${WORKDIR}/git"
+
+UBOOT_ENV_SUFFIX = "scr"
+UBOOT_ENV = "boot"
+
+EXTRA_OEMAKE += ' HOSTLDSHARED="${BUILD_CC} -shared ${BUILD_LDFLAGS} ${BUILD_CFLAGS}" '
+EXTRA_OEMAKE_append_sun50i = " BL31=${DEPLOY_DIR_IMAGE}/bl31.bin "
+
+do_compile_sun50i[depends] += "atf-sunxi:do_deploy"
+
+do_compile_append() {
+    ${B}/tools/mkimage -C none -A arm -T script -d ${WORKDIR}/boot.cmd ${WORKDIR}/${UBOOT_ENV_BINARY}
+}

recipes-devtools/python/files/olinuxino-a20som/mapping.h

@@ -0,0 +1,265 @@
+/*
+ *
+ * This file is part of pyA20SOM.
+ * mapping.h is python GPIO extension.
+ *
+ * Copyright (c) 2014 Stefan Mavrodiev @ OLIMEX LTD, <support@olimex.com>
+ *
+ * pyA20SOM is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef __MAPPING_H
+#define __MAPPING_H
+
+#include "gpio_lib.h"
+
+/**
+Structure that describe all gpio
+*/
+typedef struct _pin {
+    char name[10];          // The processor pin
+    int offset;             // Memory offset for the pin
+    int pin_number;         // Number on the connector
+}pin_t;
+
+typedef struct _gpio {
+    char connector_name[10];
+    pin_t pins[41];
+}gpio_t;
+
+
+gpio_t gpio[] = {
+    {"lcd",
+        {
+            {   "PD16", SUNXI_GPD(16),  5   },
+            {   "PD17", SUNXI_GPD(17),  6   },
+            {   "PD18", SUNXI_GPD(18),  7   },
+            {   "PD19", SUNXI_GPD(19),  8   },
+            {   "PD20", SUNXI_GPD(20),  9   },
+            {   "PD21", SUNXI_GPD(21),  10  },
+            {   "PD22", SUNXI_GPD(22),  11  },
+            {   "PD23", SUNXI_GPD(23),  12  },
+            {   "PD8", SUNXI_GPD(8),    13  },
+            {   "PD9", SUNXI_GPD(9),    14  },
+            {   "PD10", SUNXI_GPD(10),  15  },
+            {   "PD11", SUNXI_GPD(11),  16  },
+            {   "PD12", SUNXI_GPD(12),  17  },
+            {   "PD13", SUNXI_GPD(13),  18  },
+            {   "PD14", SUNXI_GPD(14),  19  },
+            {   "PD15", SUNXI_GPD(15),  20  },
+            {   "PD0",  SUNXI_GPD(0),   21  },
+            {   "PD1",  SUNXI_GPD(1),   22  },
+            {   "PD2",  SUNXI_GPD(2),   23  },
+            {   "PD3",  SUNXI_GPD(3),   24  },
+            {   "PD4",  SUNXI_GPD(4),   25  },
+            {   "PD5",  SUNXI_GPD(5),   26  },
+            {   "PD6",  SUNXI_GPD(6),   27  },
+            {   "PD7",  SUNXI_GPD(7),   28  },
+            {   "PD26", SUNXI_GPD(26),  29  },
+            {   "PD27", SUNXI_GPD(27),  30  },
+            {   "PD24", SUNXI_GPD(24),  31  },
+            {   "PD25", SUNXI_GPD(25),  32  },
+            {   "PH7",  SUNXI_GPH(7),   35  },
+            {   "PB2",  SUNXI_GPB(2),   36  },
+            {
+                {   0,  0,  0}
+            },
+        }
+    },
+    {"gpio1",
+        {
+            {   "PB9",  SUNXI_GPB(9),   7   },
+            {   "PH5",  SUNXI_GPH(5),   9   },
+            {   "PH4",  SUNXI_GPH(4),   11  },
+            {   "PH6",  SUNXI_GPH(6),   13  },
+            {   "PH3",  SUNXI_GPH(3),   15  },
+            {   "PI0",  SUNXI_GPI(0),   29  },
+            {   "PI1",  SUNXI_GPI(1),   31  },
+            {   "PI2",  SUNXI_GPI(2),   33  },
+            {   "PI3",  SUNXI_GPI(3),   35  },
+            {   "PI10", SUNXI_GPI(10),  37  },
+            {   "PI11", SUNXI_GPI(11),  39  },
+            {   "PI14", SUNXI_GPI(14),  40  },
+            {
+                {   0,  0,  0}
+            },
+        }
+    },
+    {"gpio2",
+        {
+            {   "PB22", SUNXI_GPB(22),  21  },
+            {   "PB23", SUNXI_GPB(23),  22  },
+            {   "PA0",  SUNXI_GPA(0),   29  },
+            {   "PA1",  SUNXI_GPA(1),   27  },
+            {   "PA2",  SUNXI_GPA(2),   25  },
+            {   "PA3",  SUNXI_GPA(3),   23  },
+            {   "PA4",  SUNXI_GPA(4),   30  },
+            {   "PA5",  SUNXI_GPA(5),   28  },
+            {   "PA6",  SUNXI_GPA(6),   26  },
+            {   "PA7",  SUNXI_GPA(7),   24  },
+            {   "PA8",  SUNXI_GPA(8),   33  },
+            {   "PA9",  SUNXI_GPA(9),   35  },
+            {   "PA10", SUNXI_GPA(10),  31  },
+            {   "PA11", SUNXI_GPA(11),  37  },
+            {   "PA12", SUNXI_GPA(12),  39  },
+            {   "PA13", SUNXI_GPA(13),  32  },
+            {   "PA14", SUNXI_GPA(14),  34  },
+            {   "PA15", SUNXI_GPA(15),  36  },
+            {   "PA16", SUNXI_GPA(16),  38  },
+            {   "PA17", SUNXI_GPA(17),  40  },
+
+            {
+                {   0,  0,  0}
+            },
+        }
+    },
+
+    {"gpio3",
+        {
+            {   "PH0",  SUNXI_GPH(0),   5   },
+            {   "PH2",  SUNXI_GPH(2),   7   },
+            {   "PH8",  SUNXI_GPH(8),   9   },
+            {   "PH9",  SUNXI_GPH(9),   11  },
+            {   "PH10", SUNXI_GPH(10),  13  },
+            {   "PH11", SUNXI_GPH(11),  15  },
+            {   "PH12", SUNXI_GPH(12),  17  },
+            {   "PH13", SUNXI_GPH(13),  19  },
+            {   "PH14", SUNXI_GPH(14),  21  },
+            {   "PH15", SUNXI_GPH(15),  23  },
+            {   "PH16", SUNXI_GPH(16),  25  },
+            {   "PH17", SUNXI_GPH(17),  27  },
+            {   "PH18", SUNXI_GPH(18),  29  },
+            {   "PH19", SUNXI_GPH(19),  31  },
+            {   "PH20", SUNXI_GPH(20),  33  },
+            {   "PH21", SUNXI_GPH(21),  35  },
+            {   "PH22", SUNXI_GPH(22),  37  },
+            {   "PH23", SUNXI_GPH(23),  39  },
+
+            {   "PB3",  SUNXI_GPB(3),   6   },
+            {   "PB4",  SUNXI_GPB(4),   8   },
+            {   "PB5",  SUNXI_GPB(5),   10  },
+            {   "PB6",  SUNXI_GPB(6),   12  },
+            {   "PB7",  SUNXI_GPB(7),   14  },
+            {   "PB8",  SUNXI_GPB(8),   16  },
+            {   "PB10",  SUNXI_GPB(10), 18  },
+            {   "PB11",  SUNXI_GPB(11), 20  },
+            {   "PB12",  SUNXI_GPB(12), 22  },
+            {   "PB13",  SUNXI_GPB(13), 24  },
+            {   "PB14",  SUNXI_GPB(14), 26  },
+            {   "PB15",  SUNXI_GPB(15), 28  },
+            {   "PB16",  SUNXI_GPB(16), 30  },
+            {   "PB17",  SUNXI_GPB(17), 32  },
+            {   "PH24",  SUNXI_GPH(24), 34  },
+            {   "PH25",  SUNXI_GPH(25), 36  },
+            {   "PH26",  SUNXI_GPH(26), 38  },
+            {   "PH27",  SUNXI_GPH(27), 40  },
+            {
+                {   0,  0,  0}
+            },
+        }
+    },
+
+    {"gpio4",
+        {
+            {   "PB0",  SUNXI_GPB(0),   5   },
+            {   "PB1",  SUNXI_GPB(1),   7   },
+            {   "PE0",  SUNXI_GPE(0),   6   },
+            {   "PE1",  SUNXI_GPE(1),   8   },
+            {   "PE2",  SUNXI_GPE(2),   10  },
+            {   "PE3",  SUNXI_GPE(3),   12  },
+            {   "PE4",  SUNXI_GPE(4),   14  },
+            {   "PE5",  SUNXI_GPE(5),   16  },
+            {   "PE6",  SUNXI_GPE(0),   18  },
+            {   "PE7",  SUNXI_GPE(0),   9   },
+            {   "PE8",  SUNXI_GPE(0),   11  },
+            {   "PE9",  SUNXI_GPE(0),   13  },
+            {   "PE10", SUNXI_GPE(0),   15  },
+            {   "PE11", SUNXI_GPE(0),   17  },
+            {   "PI20", SUNXI_GPI(20),  19  },
+            {   "PI21", SUNXI_GPI(21),  20  },
+            {   "PB18",  SUNXI_GPB(18), 21  },
+            {   "PB19",  SUNXI_GPB(19), 22  },
+            {   "PI16",  SUNXI_GPI(16), 23  },
+            {   "PI17",  SUNXI_GPI(17), 24  },
+            {   "PI18",  SUNXI_GPI(18), 25  },
+            {   "PI19",  SUNXI_GPI(19), 26  },
+            {   "PI12",  SUNXI_GPI(12), 27  },
+            {   "PI13",  SUNXI_GPI(13), 28  },
+            {   "PB20",  SUNXI_GPB(20), 29  },
+            {   "PB21",  SUNXI_GPB(21), 30  },
+            {   "PC22",  SUNXI_GPC(22), 31  },
+            {   "PC21",  SUNXI_GPC(21), 32  },
+            {   "PC20",  SUNXI_GPC(20), 33  },
+            {   "PC19",  SUNXI_GPC(21), 34  },
+            {   "PI15",  SUNXI_GPI(15), 36  },
+            {
+                {   0,  0,  0}
+            },
+        }
+    },
+
+    {"gpio5",
+        {
+            {   "PG0",  SUNXI_GPG(0),   1   },
+            {   "PG1",  SUNXI_GPG(1),   3   },
+            {   "PG2",  SUNXI_GPG(2),   5   },
+            {   "PG3",  SUNXI_GPG(3),   7   },
+            {   "PG4",  SUNXI_GPG(4),   9   },
+            {   "PG5",  SUNXI_GPG(5),   11  },
+            {   "PG6",  SUNXI_GPG(6),   13  },
+            {   "PG7",  SUNXI_GPG(7),   15  },
+            {   "PG8",  SUNXI_GPG(8),   17  },
+            {   "PG9",  SUNXI_GPG(9),   19  },
+            {   "PG10", SUNXI_GPG(10),  21  },
+            {   "PG11", SUNXI_GPG(11),  23  },
+            {   "PC8",  SUNXI_GPC(8),   25  },
+            {   "PC9",  SUNXI_GPC(9),   27  },
+            {   "PC10", SUNXI_GPC(10),  29  },
+            {   "PC11", SUNXI_GPC(11),  31  },
+            {   "PC12", SUNXI_GPC(12),  33  },
+            {   "PC13", SUNXI_GPC(13),  35  },
+            {   "PC14", SUNXI_GPC(14),  37  },
+            {   "PC15", SUNXI_GPC(15),  39  },
+            {   "PI6",  SUNXI_GPI(6),   4   },
+            {   "PI7",  SUNXI_GPI(7),   6   },
+            {   "PI8",  SUNXI_GPI(8),   8   },
+            {   "PI9",  SUNXI_GPI(9),   10  },
+            {   "PI4",  SUNXI_GPI(4),   12  },
+            {   "PI5",  SUNXI_GPI(5),   14  },
+            {   "PC16", SUNXI_GPC(16),  16  },
+            {   "PC17", SUNXI_GPC(17),  18  },
+            {   "PC18", SUNXI_GPC(18),  20  },
+            {   "PC23", SUNXI_GPC(23),  22  },
+            {   "PC24", SUNXI_GPC(24),  24  },
+            {   "PC7",  SUNXI_GPC(7),   26  },
+            {   "PC6",  SUNXI_GPC(6),   28  },
+            {   "PC5",  SUNXI_GPC(5),   30  },
+            {   "PC3",  SUNXI_GPC(3),   32  },
+            {   "PC2",  SUNXI_GPC(2),   34  },
+            {   "PC1",  SUNXI_GPC(1),   36  },
+            {   "PC0",  SUNXI_GPC(0),   38  },
+            {   "PC4",  SUNXI_GPC(4),   40  },
+            {
+                {   0,  0,  0}
+            },
+        }
+    },
+
+};
+
+
+
+#endif

recipes-devtools/python/files/setup.py.patch

@@ -1,5 +1,5 @@
---- pyA20-0.2.0/setup.py	2014-09-04 12:17:18.000000000 +0200
-+++ pyA20-0.2.0/setup.py	2014-11-24 17:44:37.000000000 +0100
+--- pyA20-0.2.1/setup.py	2014-09-04 12:17:18.000000000 +0200
++++ pyA20-0.2.1/setup.py	2014-11-24 17:44:37.000000000 +0100
 @@ -43,31 +43,31 @@
      Detect processor type
      :return:

recipes-devtools/python/pya20_0.2.1.bb

@@ -2,13 +2,13 @@ DESCRIPTION = "A module to control Allwinner GPIO,SPI and I2C channels"
 HOMEPAGE = "https://pypi.python.org/pypi/pyA20"
 SECTION = "devel/python"
 LICENSE = "MIT"
-LIC_FILES_CHKSUM = "file://PKG-INFO;md5=b4cb7d5da6f1efc1d0bf487169e83985"
+LIC_FILES_CHKSUM = "file://PKG-INFO;md5=bfe0261ded6cff75086193ec2f79129e"
 DEPENDS = "python"
 
 # No GPIO mappings for other machines yet
-COMPATIBLE_MACHINE = "(olinuxino-a13|olinuxino-a10|olinuxino-a20|olinuxino-a10lime|olinuxino-a20lime|olinuxino-a20lime2|olinuxino-a13som)"
+COMPATIBLE_MACHINE = "(olinuxino-a13|olinuxino-a10|olinuxino-a20|olinuxino-a10lime|olinuxino-a20lime|olinuxino-a20lime2|olinuxino-a13som|olinuxino-a20som)"
 
-SRC_URI = "http://pypi.python.org/packages/source/p/pyA20/pyA20-${PV}.tar.gz \
+SRC_URI = "https://pypi.python.org/packages/source/p/pyA20/pyA20-${PV}.tar.gz \
            file://setup.py.patch \
            file://mapping.h \
           "
@@ -20,5 +20,5 @@ do_compile_prepend() {
 cp ${WORKDIR}/mapping.h ${S}/pyA20/gpio/mapping.h
 }
 
-SRC_URI[md5sum] = "b4115859834f09ebd389f810f2ffefb9"
-SRC_URI[sha256sum] = "9855747d9bbdfcce6b460fcd67d953155e39f4e002a9a4c573910248b451dad8"
+SRC_URI[md5sum] = "2290066bbe274000c53693959a8005b4"
+SRC_URI[sha256sum] = "b15e4ee1016b7eb52001cbccde3751868624a88d2adbb9adc5404628f7e59e7e"

recipes-devtools/python/pya20som_0.2.1.bb

@@ -0,0 +1,24 @@
+DESCRIPTION = "A module to control Allwinner GPIO,SPI and I2C channels"
+HOMEPAGE = "https://pypi.python.org/pypi/pyA20SOM"
+SECTION = "devel/python"
+LICENSE = "MIT"
+LIC_FILES_CHKSUM = "file://PKG-INFO;md5=cf6345f2cb2acee98b01c493d68b8322"
+DEPENDS = "python"
+
+# No GPIO mappings for other machines yet
+COMPATIBLE_MACHINE = "olinuxino-a20som"
+
+SRC_URI = "https://pypi.python.org/packages/source/p/pyA20SOM/pyA20SOM-${PV}.tar.gz \
+           file://setup.py.patch \
+           file://mapping.h \
+          "
+S = "${WORKDIR}/pyA20SOM-${PV}"
+
+inherit distutils
+
+do_compile_prepend() { 
+cp ${WORKDIR}/mapping.h ${S}/pyA20SOM/gpio/mapping.h
+}
+
+SRC_URI[md5sum] = "a720115ef1d3dffe82f42f2157ca1c56"
+SRC_URI[sha256sum] = "1ac1025596cc112964f7caac9a6a523d5da61623c248ccc178c6cbb4bc1b4549"

recipes-graphics/libgles/sunxi-mali_git.bb

@@ -3,13 +3,23 @@ DESCRIPTION = "libGLES for the A10/A13 Allwinner processor with Mali 400 (X11)"
 LICENSE = "Proprietary"
 LIC_FILES_CHKSUM = "file://README;md5=1b81a178e80ee888ee4571772699ab2c"
 
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i)"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i)"
 
 # These libraries shouldn't get installed in world builds unless something
 # explicitly depends upon them.
 EXCLUDE_FROM_WORLD = "1"
 PROVIDES = "virtual/libgles1 virtual/libgles2 virtual/egl"
-RPROVIDES_${PN} += "libGLESv2.so libEGL.so libGLESv2.so libGLESv1_CM.so libMali.so"
+
+# There's only hardfp version available
+python __anonymous() {
+    tunes = d.getVar("TUNE_FEATURES", True)
+    if not tunes:
+        return
+    if "callconvention-hard" not in tunes:
+        pkgn = d.getVar("PN", True)
+        pkgv = d.getVar("PV", True)
+        raise bb.parse.SkipPackage("%s-%s ONLY supports hardfp mode for now" % (pkgn, pkgv))
+}
 
 SRCREV_pn-${PN} = "d343311efc8db166d8371b28494f0f27b6a58724"
 SRC_URI = "gitsm://github.com/linux-sunxi/sunxi-mali.git \
@@ -79,8 +89,14 @@ do_install() {
 
 # Packages like xf86-video-fbturbo dlopen() libUMP.so, so we do need to ship the .so files in ${PN}
 PACKAGES =+ "${PN}-test"
+
+RPROVIDES_${PN} += "libGLESv2.so libEGL.so libGLESv2.so libGLESv1_CM.so libMali.so"
+RDEPENDS_${PN}-test = "${PN}"
+
 FILES_${PN} += "${libdir}/lib*.so"
 FILES_${PN}-dev = "${includedir} ${libdir}/pkgconfig/*"
 FILES_${PN}-test = "${bindir}/sunximali-test"
+
 # These are closed binaries generated elsewhere so don't check ldflags & text relocations
 INSANE_SKIP_${PN} = "dev-so ldflags textrel"
+INSANE_SKIP_${PN}-test = "dev-so ldflags textrel"

recipes-graphics/tslib/tslib/0001-Support-reading-coordinates-from-multitouch-devices.patch

@@ -1,79 +0,0 @@
-From c525c0b5d8eada982c99442454fcf7b8364e10b3 Mon Sep 17 00:00:00 2001
-From: Florian Boor <florian@kernelconcepts.de>
-Date: Fri, 1 Apr 2011 23:30:21 +0200
-Subject: [PATCH] Support reading coordinates from multitouch devices.
-
-Signed-off-by: Florian Boor <florian@kernelconcepts.de>
-Signed-off-by: Christopher Larson <kergoth@gmail.com>
----
- plugins/input-raw.c | 33 +++++++++++++++++++++++----------
- 1 file changed, 23 insertions(+), 10 deletions(-)
-
-diff --git a/plugins/input-raw.c b/plugins/input-raw.c
-index 4396eab..1e48505 100644
---- a/plugins/input-raw.c
-+++ b/plugins/input-raw.c
-@@ -40,6 +40,11 @@
- # define KEY_CNT (KEY_MAX+1)
- #endif
- 
-+#ifndef ABS_MT_POSITION_X
-+# define ABS_MT_POSITION_X       0x35    /* Center X ellipse position */
-+# define ABS_MT_POSITION_Y       0x36    /* Center Y ellipse position */
-+#endif
-+
- #include "tslib-private.h"
- 
- #define GRAB_EVENTS_WANTED	1
-@@ -160,16 +165,17 @@ static int ts_input_read(struct tslib_module_info *inf,
- 				}
- 				break;
- 			case EV_SYN:
--				/* Fill out a new complete event */
--				if (pen_up) {
--					samp->x = 0;
--					samp->y = 0;
--					samp->pressure = 0;
--					pen_up = 0;
--				} else {
--					samp->x = i->current_x;
--					samp->y = i->current_y;
--					samp->pressure = i->current_p;
-+				if (ev.code == SYN_REPORT) {
-+					/* Fill out a new complete event */
-+					if (pen_up) {
-+						samp->x = 0;
-+						samp->y = 0;
-+						samp->pressure = 0;
-+						pen_up = 0;
-+					} else {
-+						samp->x = i->current_x;
-+						samp->y = i->current_y;
-+						samp->pressure = i->current_p;
- 				}
- 				samp->tv = ev.time;
- 	#ifdef DEBUG
-@@ -179,6 +185,7 @@ static int ts_input_read(struct tslib_module_info *inf,
- 	#endif /* DEBUG */
- 				samp++;
- 				total++;
-+				}
- 				break;
- 			case EV_ABS:
- 				switch (ev.code) {
-@@ -188,6 +195,12 @@ static int ts_input_read(struct tslib_module_info *inf,
- 				case ABS_Y:
- 					i->current_y = ev.value;
- 					break;
-+				case ABS_MT_POSITION_X:
-+					i->current_x = ev.value;
-+					break;
-+				case ABS_MT_POSITION_Y:
-+					i->current_y = ev.value;
-+					break;
- 				case ABS_PRESSURE:
- 					i->current_p = ev.value;
- 					break;
--- 
-1.8.1.4
-

recipes-kernel/linux/linux-mainline/0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch

@@ -0,0 +1,80 @@
+From 4ca766a768e783ee5198f1935b7f46a5df9b4a35 Mon Sep 17 00:00:00 2001
+From: Jelle van der Waa <jelle@vdwaa.nl>
+Date: Tue, 23 Jan 2018 15:58:44 -0800
+Subject: [PATCH] ARM: dts: nanopi-neo-air: Add WiFi / eMMC
+
+Enable the WiFi (AP6212) chip and eMMC support for the NanoPi NEO Air.
+
+This patch was originally submitted by Jelle van der Waa. Martin Kelly
+modified it to compile on the latest kernel, fixed up some review
+comments from Maxime Ripard, and re-tested the patch.
+
+The patch has been reworked to add back eMMC support which has been left
+out at the last backport.
+
+Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
+Cc: linux-sunxi@googlegroups.com
+Cc: devicetree@vger.kernel.org
+Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
+Signed-off-by: Martin Kelly <mkelly@xevo.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+Signed-off-by: Florin Sarbu <florin@resin.io>
+---
+ arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 34 +++++++++++++++++++++++++++
+ 1 file changed, 34 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+index 03ff6f8..a9331fe 100644
+--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
++++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+@@ -72,6 +72,11 @@
+ 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
+ 		};
+ 	};
++
++	wifi_pwrseq: wifi_pwrseq {
++		compatible = "mmc-pwrseq-simple";
++		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
++	};
+ };
+ 
+ &mmc0 {
+@@ -84,6 +89,35 @@
+ 	status = "okay";
+ };
+ 
++&mmc1 {
++	pinctrl-names = "default";
++	pinctrl-0 = <&mmc1_pins_a>;
++	vmmc-supply = <&reg_vcc3v3>;
++	vqmmc-supply = <&reg_vcc3v3>;
++	mmc-pwrseq = <&wifi_pwrseq>;
++	bus-width = <4>;
++	non-removable;
++	status = "okay";
++
++	brcmf: bcrmf@1 {
++		reg = <1>;
++		compatible = "brcm,bcm4329-fmac";
++		interrupt-parent = <&pio>;
++		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
++		interrupt-names = "host-wake";
++	};
++};
++
++&mmc2 {
++	pinctrl-names = "default";
++	pinctrl-0 = <&mmc2_8bit_pins>;
++	vmmc-supply = <&reg_vcc3v3>;
++	vqmmc-supply = <&reg_vcc3v3>;
++	bus-width = <8>;
++	non-removable;
++	status = "okay";
++};
++
+ &uart0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&uart0_pins_a>;
+-- 
+2.11.0
+

recipes-kernel/linux/linux-mainline/aarch64/defconfig

@@ -0,0 +1,612 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IRQ_TIME_ACCOUNTING=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_NUMA_BALANCING=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_SWAP=y
+CONFIG_BLK_CGROUP=y
+CONFIG_CGROUP_PIDS=y
+CONFIG_CGROUP_HUGETLB=y
+CONFIG_CPUSETS=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_CGROUP_PERF=y
+CONFIG_USER_NS=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_PROFILING=y
+CONFIG_JUMP_LABEL=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_ARCH_SUNXI=y
+CONFIG_ARCH_ALPINE=y
+CONFIG_ARCH_BCM2835=y
+CONFIG_ARCH_BCM_IPROC=y
+CONFIG_ARCH_BERLIN=y
+CONFIG_ARCH_BRCMSTB=y
+CONFIG_ARCH_EXYNOS=y
+CONFIG_ARCH_LAYERSCAPE=y
+CONFIG_ARCH_LG1K=y
+CONFIG_ARCH_HISI=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_ARCH_MESON=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_ARCH_QCOM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_ARCH_SEATTLE=y
+CONFIG_ARCH_RENESAS=y
+CONFIG_ARCH_R8A7795=y
+CONFIG_ARCH_R8A7796=y
+CONFIG_ARCH_STRATIX10=y
+CONFIG_ARCH_TEGRA=y
+CONFIG_ARCH_SPRD=y
+CONFIG_ARCH_THUNDER=y
+CONFIG_ARCH_THUNDER2=y
+CONFIG_ARCH_UNIPHIER=y
+CONFIG_ARCH_VEXPRESS=y
+CONFIG_ARCH_XGENE=y
+CONFIG_ARCH_ZX=y
+CONFIG_ARCH_ZYNQMP=y
+CONFIG_PCI=y
+CONFIG_HOTPLUG_PCI_PCIE=y
+CONFIG_PCI_IOV=y
+CONFIG_HOTPLUG_PCI=y
+CONFIG_HOTPLUG_PCI_ACPI=y
+CONFIG_PCI_LAYERSCAPE=y
+CONFIG_PCI_HISI=y
+CONFIG_PCIE_QCOM=y
+CONFIG_PCIE_KIRIN=y
+CONFIG_PCIE_ARMADA_8K=y
+CONFIG_PCI_AARDVARK=y
+CONFIG_PCIE_RCAR=y
+CONFIG_PCIE_ROCKCHIP=m
+CONFIG_PCI_HOST_GENERIC=y
+CONFIG_PCI_XGENE=y
+CONFIG_ARM64_VA_BITS_48=y
+CONFIG_SCHED_MC=y
+CONFIG_NUMA=y
+CONFIG_PREEMPT=y
+CONFIG_KSM=y
+CONFIG_TRANSPARENT_HUGEPAGE=y
+CONFIG_CMA=y
+CONFIG_SECCOMP=y
+CONFIG_KEXEC=y
+CONFIG_CRASH_DUMP=y
+CONFIG_XEN=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_COMPAT=y
+CONFIG_HIBERNATION=y
+CONFIG_WQ_POWER_EFFICIENT_DEFAULT=y
+CONFIG_ARM_CPUIDLE=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_ARM_BIG_LITTLE_CPUFREQ=y
+CONFIG_ARM_SCPI_CPUFREQ=y
+CONFIG_ACPI_CPPC_CPUFREQ=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IPV6=m
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
+CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NF_CONNTRACK_IPV4=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_NAT=m
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_NF_CONNTRACK_IPV6=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_NAT=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_BRIDGE=m
+CONFIG_BRIDGE_VLAN_FILTERING=y
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_VLAN_8021Q_MVRP=y
+CONFIG_BPF_JIT=y
+CONFIG_BT=m
+CONFIG_BT_HIDP=m
+# CONFIG_BT_HS is not set
+# CONFIG_BT_LE is not set
+CONFIG_BT_LEDS=y
+# CONFIG_BT_DEBUGFS is not set
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_LL=y
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_LEDS=y
+CONFIG_RFKILL=m
+CONFIG_NET_9P=y
+CONFIG_NET_9P_VIRTIO=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_DMA_CMA=y
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_DENALI_DT=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_NBD=m
+CONFIG_VIRTIO_BLK=y
+CONFIG_BLK_DEV_NVME=m
+CONFIG_SRAM=y
+CONFIG_EEPROM_AT25=m
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_SAS_ATA=y
+CONFIG_SCSI_HISI_SAS=y
+CONFIG_SCSI_HISI_SAS_PCI=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI=y
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_AHCI_CEVA=y
+CONFIG_AHCI_MVEBU=y
+CONFIG_AHCI_XGENE=y
+CONFIG_AHCI_QORIQ=y
+CONFIG_SATA_SIL24=y
+CONFIG_SATA_RCAR=y
+CONFIG_PATA_PLATFORM=y
+CONFIG_PATA_OF_PLATFORM=y
+CONFIG_NETDEVICES=y
+CONFIG_MACVLAN=m
+CONFIG_MACVTAP=m
+CONFIG_TUN=y
+CONFIG_VETH=m
+CONFIG_VIRTIO_NET=y
+CONFIG_AMD_XGBE=y
+CONFIG_NET_XGENE=y
+CONFIG_MACB=y
+CONFIG_HNS_DSAF=y
+CONFIG_HNS_ENET=y
+CONFIG_E1000E=y
+CONFIG_IGB=y
+CONFIG_IGBVF=y
+CONFIG_MVNETA=y
+CONFIG_MVPP2=y
+CONFIG_SKY2=y
+CONFIG_QCOM_EMAC=m
+CONFIG_RAVB=y
+CONFIG_SMC91X=y
+CONFIG_SMSC911X=y
+CONFIG_STMMAC_ETH=m
+CONFIG_MDIO_BUS_MUX_MMIOREG=y
+CONFIG_AT803X_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_MESON_GXL_PHY=m
+CONFIG_MICREL_PHY=y
+CONFIG_REALTEK_PHY=m
+CONFIG_ROCKCHIP_PHY=y
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_RTL8152=m
+CONFIG_USB_USBNET=m
+CONFIG_USB_NET_DM9601=m
+CONFIG_USB_NET_SR9800=m
+CONFIG_USB_NET_SMSC75XX=m
+CONFIG_USB_NET_SMSC95XX=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_BRCMFMAC=m
+CONFIG_WL18XX=m
+CONFIG_WLCORE_SDIO=m
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_ADC=m
+CONFIG_KEYBOARD_CROS_EC=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_PM8941_PWRKEY=y
+CONFIG_INPUT_HISI_POWERKEY=y
+# CONFIG_SERIO_SERPORT is not set
+CONFIG_SERIO_AMBAKMI=y
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_BCM2835AUX=y
+CONFIG_SERIAL_8250_DW=y
+CONFIG_SERIAL_8250_MT6577=y
+CONFIG_SERIAL_8250_UNIPHIER=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_MESON=y
+CONFIG_SERIAL_MESON_CONSOLE=y
+CONFIG_SERIAL_SAMSUNG=y
+CONFIG_SERIAL_SAMSUNG_CONSOLE=y
+CONFIG_SERIAL_TEGRA=y
+CONFIG_SERIAL_SH_SCI=y
+CONFIG_SERIAL_SH_SCI_NR_UARTS=11
+CONFIG_SERIAL_SH_SCI_CONSOLE=y
+CONFIG_SERIAL_MSM=y
+CONFIG_SERIAL_MSM_CONSOLE=y
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
+CONFIG_SERIAL_MVEBU_UART=y
+CONFIG_SERIAL_DEV_BUS=y
+CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
+CONFIG_VIRTIO_CONSOLE=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_I2C_BCM2835=m
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_I2C_IMX=y
+CONFIG_I2C_MESON=y
+CONFIG_I2C_MV64XXX=y
+CONFIG_I2C_PXA=y
+CONFIG_I2C_QUP=y
+CONFIG_I2C_RK3X=y
+CONFIG_I2C_SH_MOBILE=y
+CONFIG_I2C_TEGRA=y
+CONFIG_I2C_UNIPHIER_F=y
+CONFIG_I2C_RCAR=y
+CONFIG_I2C_CROS_EC_TUNNEL=y
+CONFIG_SPI=y
+CONFIG_SPI_MESON_SPICC=m
+CONFIG_SPI_MESON_SPIFC=m
+CONFIG_SPI_BCM2835=m
+CONFIG_SPI_BCM2835AUX=m
+CONFIG_SPI_ORION=y
+CONFIG_SPI_PL022=y
+CONFIG_SPI_QUP=y
+CONFIG_SPI_ROCKCHIP=y
+CONFIG_SPI_S3C64XX=y
+CONFIG_SPI_SPIDEV=m
+CONFIG_SPMI=y
+CONFIG_PINCTRL_IPQ8074=y
+CONFIG_PINCTRL_SINGLE=y
+CONFIG_PINCTRL_MAX77620=y
+CONFIG_PINCTRL_MSM8916=y
+CONFIG_PINCTRL_MSM8994=y
+CONFIG_PINCTRL_MSM8996=y
+CONFIG_PINCTRL_QDF2XXX=y
+CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
+CONFIG_GPIO_DWAPB=y
+CONFIG_GPIO_PL061=y
+CONFIG_GPIO_RCAR=y
+CONFIG_GPIO_XGENE=y
+CONFIG_GPIO_XGENE_SB=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_PCA953X_IRQ=y
+CONFIG_GPIO_MAX77620=y
+CONFIG_POWER_RESET_MSM=y
+CONFIG_POWER_RESET_XGENE=y
+CONFIG_POWER_RESET_SYSCON=y
+CONFIG_SYSCON_REBOOT_MODE=y
+CONFIG_BATTERY_BQ27XXX=y
+CONFIG_SENSORS_ARM_SCPI=y
+CONFIG_SENSORS_LM90=m
+CONFIG_SENSORS_INA2XX=m
+CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
+CONFIG_CPU_THERMAL=y
+CONFIG_THERMAL_EMULATION=y
+CONFIG_BRCMSTB_THERMAL=m
+CONFIG_EXYNOS_THERMAL=y
+CONFIG_ROCKCHIP_THERMAL=m
+CONFIG_WATCHDOG=y
+CONFIG_S3C2410_WATCHDOG=y
+CONFIG_MESON_GXBB_WATCHDOG=m
+CONFIG_MESON_WATCHDOG=m
+CONFIG_RENESAS_WDT=y
+CONFIG_UNIPHIER_WATCHDOG=y
+CONFIG_BCM2835_WDT=y
+CONFIG_MFD_AXP20X_RSB=y
+CONFIG_MFD_CROS_EC=y
+CONFIG_MFD_CROS_EC_I2C=y
+CONFIG_MFD_CROS_EC_SPI=y
+CONFIG_MFD_EXYNOS_LPASS=m
+CONFIG_MFD_HI6421_PMIC=y
+CONFIG_MFD_HI655X_PMIC=y
+CONFIG_MFD_MAX77620=y
+CONFIG_MFD_SPMI_PMIC=y
+CONFIG_MFD_RK808=y
+CONFIG_MFD_SEC_CORE=y
+CONFIG_REGULATOR_AXP20X=y
+CONFIG_REGULATOR_FAN53555=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_GPIO=y
+CONFIG_REGULATOR_HI6421V530=y
+CONFIG_REGULATOR_HI655X=y
+CONFIG_REGULATOR_MAX77620=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_REGULATOR_QCOM_SMD_RPM=y
+CONFIG_REGULATOR_QCOM_SPMI=y
+CONFIG_REGULATOR_RK808=y
+CONFIG_REGULATOR_S2MPS11=y
+CONFIG_MEDIA_SUPPORT=m
+CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
+CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
+CONFIG_MEDIA_CONTROLLER=y
+CONFIG_MEDIA_RC_SUPPORT=y
+CONFIG_RC_CORE=m
+CONFIG_RC_DEVICES=y
+CONFIG_RC_DECODERS=y
+CONFIG_IR_MESON=m
+CONFIG_VIDEO_V4L2_SUBDEV_API=y
+# CONFIG_DVB_NET is not set
+CONFIG_V4L_MEM2MEM_DRIVERS=y
+CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
+CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
+CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
+CONFIG_VIDEO_RENESAS_FCP=m
+CONFIG_VIDEO_RENESAS_VSP1=m
+CONFIG_DRM=m
+CONFIG_DRM_NOUVEAU=m
+CONFIG_DRM_EXYNOS=m
+CONFIG_DRM_EXYNOS5433_DECON=y
+CONFIG_DRM_EXYNOS7_DECON=y
+CONFIG_DRM_EXYNOS_DSI=y
+# CONFIG_DRM_EXYNOS_DP is not set
+CONFIG_DRM_EXYNOS_HDMI=y
+CONFIG_DRM_EXYNOS_MIC=y
+CONFIG_DRM_ROCKCHIP=m
+CONFIG_ROCKCHIP_ANALOGIX_DP=y
+CONFIG_ROCKCHIP_CDN_DP=y
+CONFIG_ROCKCHIP_DW_HDMI=y
+CONFIG_ROCKCHIP_DW_MIPI_DSI=y
+CONFIG_ROCKCHIP_INNO_HDMI=y
+CONFIG_DRM_RCAR_DU=m
+CONFIG_DRM_RCAR_LVDS=y
+CONFIG_DRM_RCAR_VSP=y
+CONFIG_DRM_TEGRA=m
+CONFIG_DRM_PANEL_SIMPLE=m
+CONFIG_DRM_I2C_ADV7511=m
+CONFIG_DRM_VC4=m
+CONFIG_DRM_HISI_KIRIN=m
+CONFIG_DRM_MESON=m
+CONFIG_FB=y
+CONFIG_FB_ARMCLCD=y
+CONFIG_BACKLIGHT_GENERIC=m
+CONFIG_BACKLIGHT_PWM=m
+CONFIG_BACKLIGHT_LP855X=m
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_BCM2835_SOC_I2S=m
+CONFIG_SND_SOC_SAMSUNG=y
+CONFIG_SND_SOC_RCAR=m
+CONFIG_SND_SOC_AK4613=m
+CONFIG_SND_SIMPLE_CARD=y
+CONFIG_USB=y
+CONFIG_USB_OTG=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_TEGRA=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_MSM=y
+CONFIG_USB_EHCI_EXYNOS=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_EXYNOS=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_RENESAS_USBHS=m
+CONFIG_USB_STORAGE=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_CHIPIDEA=y
+CONFIG_USB_CHIPIDEA_UDC=y
+CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_USB_ISP1760=y
+CONFIG_USB_HSIC_USB3503=y
+CONFIG_NOP_USB_XCEIV=y
+CONFIG_USB_MSM_OTG=y
+CONFIG_USB_QCOM_8X16_PHY=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_RENESAS_USBHS_UDC=m
+CONFIG_USB_MUSB_HDRC=y
+# Restrict to host mode, as it is hard-coded that way in the device tree
+# (dr_mode = "host" in the &usb_otg node)
+CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_MUSB_SUNXI=y
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK_MINORS=32
+CONFIG_MMC_ARMMMCI=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ACPI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_OF_ARASAN=y
+CONFIG_MMC_SDHCI_OF_ESDHC=y
+CONFIG_MMC_SDHCI_CADENCE=y
+CONFIG_MMC_SDHCI_TEGRA=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MMC_SDHCI_MSM=y
+CONFIG_MMC_SPI=y
+CONFIG_MMC_SDHI=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_EXYNOS=y
+CONFIG_MMC_DW_K3=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SUNXI=y
+CONFIG_MMC_BCM2835=y
+CONFIG_MMC_SDHCI_XENON=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_PWM=y
+CONFIG_LEDS_SYSCON=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_EDAC=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MAX77686=y
+CONFIG_RTC_DRV_RK808=m
+CONFIG_RTC_DRV_S5M=y
+CONFIG_RTC_DRV_DS3232=y
+CONFIG_RTC_DRV_EFI=y
+CONFIG_RTC_DRV_S3C=y
+CONFIG_RTC_DRV_PL031=y
+CONFIG_RTC_DRV_SUN6I=y
+CONFIG_RTC_DRV_TEGRA=y
+CONFIG_RTC_DRV_XGENE=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_BCM2835=m
+CONFIG_K3_DMA=y
+CONFIG_MV_XOR_V2=y
+CONFIG_PL330_DMA=y
+CONFIG_TEGRA20_APB_DMA=y
+CONFIG_QCOM_BAM_DMA=y
+CONFIG_QCOM_HIDMA_MGMT=y
+CONFIG_QCOM_HIDMA=y
+CONFIG_RCAR_DMAC=y
+CONFIG_VFIO=y
+CONFIG_VFIO_PCI=y
+CONFIG_VIRTIO_PCI=y
+CONFIG_VIRTIO_BALLOON=y
+CONFIG_VIRTIO_MMIO=y
+CONFIG_XEN_GNTDEV=y
+CONFIG_XEN_GRANT_DEV_ALLOC=y
+CONFIG_COMMON_CLK_RK808=y
+CONFIG_COMMON_CLK_SCPI=y
+CONFIG_COMMON_CLK_CS2000_CP=y
+CONFIG_COMMON_CLK_S2MPS11=y
+CONFIG_CLK_QORIQ=y
+CONFIG_COMMON_CLK_PWM=y
+CONFIG_COMMON_CLK_QCOM=y
+CONFIG_QCOM_CLK_SMD_RPM=y
+CONFIG_IPQ_GCC_8074=y
+CONFIG_MSM_GCC_8916=y
+CONFIG_MSM_GCC_8994=y
+CONFIG_MSM_MMCC_8996=y
+CONFIG_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_QCOM=y
+CONFIG_ARM_MHU=y
+CONFIG_PLATFORM_MHU=y
+CONFIG_BCM2835_MBOX=y
+CONFIG_HI6220_MBOX=y
+CONFIG_ROCKCHIP_IOMMU=y
+CONFIG_ARM_SMMU=y
+CONFIG_ARM_SMMU_V3=y
+CONFIG_RPMSG_QCOM_SMD=y
+CONFIG_RASPBERRYPI_POWER=y
+CONFIG_QCOM_SMEM=y
+CONFIG_QCOM_SMD_RPM=y
+CONFIG_QCOM_SMP2P=y
+CONFIG_QCOM_SMSM=y
+CONFIG_ROCKCHIP_PM_DOMAINS=y
+CONFIG_ARCH_TEGRA_132_SOC=y
+CONFIG_ARCH_TEGRA_210_SOC=y
+CONFIG_ARCH_TEGRA_186_SOC=y
+CONFIG_EXTCON_USB_GPIO=y
+CONFIG_IIO=y
+CONFIG_EXYNOS_ADC=y
+CONFIG_ROCKCHIP_SARADC=m
+CONFIG_PWM=y
+CONFIG_PWM_BCM2835=m
+CONFIG_PWM_CROS_EC=m
+CONFIG_PWM_MESON=m
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_PWM_SAMSUNG=y
+CONFIG_PWM_TEGRA=m
+CONFIG_PHY_RCAR_GEN3_USB2=y
+CONFIG_PHY_HI6220_USB=y
+CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_EMMC=y
+CONFIG_PHY_ROCKCHIP_PCIE=m
+CONFIG_PHY_XGENE=y
+CONFIG_PHY_TEGRA_XUSB=y
+CONFIG_QCOM_L2_PMU=y
+CONFIG_QCOM_L3_PMU=y
+CONFIG_TEE=y
+CONFIG_OPTEE=y
+CONFIG_ARM_SCPI_PROTOCOL=y
+CONFIG_RASPBERRYPI_FIRMWARE=y
+CONFIG_EFI_CAPSULE_LOADER=y
+CONFIG_ACPI=y
+CONFIG_ACPI_APEI=y
+CONFIG_ACPI_APEI_GHES=y
+CONFIG_ACPI_APEI_PCIEAER=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
+CONFIG_FANOTIFY=y
+CONFIG_FANOTIFY_ACCESS_PERMISSIONS=y
+CONFIG_QUOTA=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
+CONFIG_OVERLAY_FS=m
+CONFIG_VFAT_FS=y
+CONFIG_HUGETLBFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_EFIVAR_FS=y
+CONFIG_SQUASHFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_V4_2=y
+CONFIG_ROOT_NFS=y
+CONFIG_9P_FS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_VIRTUALIZATION=y
+CONFIG_KVM=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_LOCKUP_DETECTOR=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
+CONFIG_MEMTEST=y
+CONFIG_SECURITY=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_ANSI_CPRNG=y
+CONFIG_ARM64_CRYPTO=y
+CONFIG_CRYPTO_SHA256_ARM64=m
+CONFIG_CRYPTO_SHA512_ARM64=m
+CONFIG_CRYPTO_SHA1_ARM64_CE=y
+CONFIG_CRYPTO_SHA2_ARM64_CE=y
+CONFIG_CRYPTO_GHASH_ARM64_CE=y
+CONFIG_CRYPTO_CRCT10DIF_ARM64_CE=m
+CONFIG_CRYPTO_CRC32_ARM64_CE=m
+CONFIG_CRYPTO_AES_ARM64=m
+CONFIG_CRYPTO_AES_ARM64_CE=m
+CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
+CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
+CONFIG_CRYPTO_AES_ARM64_NEON_BLK=m
+CONFIG_CRYPTO_CHACHA20_NEON=m
+CONFIG_CRYPTO_AES_ARM64_BS=m

recipes-kernel/linux/linux-mainline/arm/defconfig

@@ -511,6 +511,7 @@ CONFIG_GPIO_SYSFS=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_POWER_RESET=y
 CONFIG_THERMAL=y
+CONFIG_THERMAL_OF=y
 CONFIG_CPU_THERMAL=y
 CONFIG_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=y
@@ -687,6 +688,27 @@ CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_SIMPLE=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KEYSPAN_MPR=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19=y
+CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
+CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
+CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_PL2303=m
 CONFIG_MMC=y
 CONFIG_MMC_SUNXI=y
 CONFIG_LEDS_CLASS=y
@@ -729,9 +751,23 @@ CONFIG_PWM_SUN4I=y
 CONFIG_PHY_SUN4I_USB=y
 CONFIG_PHY_SUN9I_USB=y
 CONFIG_EXT4_FS=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
 CONFIG_FANOTIFY=y
 CONFIG_AUTOFS4_FS=m
 CONFIG_FUSE_FS=m
+CONFIG_OVERLAY_FS=m
+CONFIG_FSCACHE=m
+CONFIG_FSCACHE_STATS=y
+CONFIG_FSCACHE_HISTOGRAM=y
+CONFIG_CACHEFILES=m
+CONFIG_CACHEFILES_HISTOGRAM=y
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_NFS_FS=y
@@ -747,3 +783,4 @@ CONFIG_CRYPTO_SHA1_ARM_NEON=y
 CONFIG_CRYPTO_SHA256_ARM=y
 CONFIG_CRYPTO_SHA512_ARM_NEON=y
 CONFIG_CRYPTO_AES_ARM_BS=y
+CONFIG_USB_STORAGE=y

recipes-kernel/linux/linux-mainline/orange-pi-zero/0001-add-wifi-support.patch

@@ -0,0 +1,79 @@
+diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+index 6713d0f2b3f4..ad0829e8f716 100644
+--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
++++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+@@ -80,19 +80,22 @@
+ 		};
+ 	};
+ 
+-	reg_vcc_wifi: reg_vcc_wifi {
++	vdd_wifi: vdd_wifi {
+ 		compatible = "regulator-fixed";
+-		regulator-min-microvolt = <3300000>;
+-		regulator-max-microvolt = <3300000>;
+-		regulator-name = "vcc-wifi";
+-		enable-active-high;
++		regulator-name = "wifi";
++		regulator-min-microvolt = <1800000>;
++		regulator-max-microvolt = <1800000>;
+ 		gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
++		startup-delay-us = <70000>;
++		enable-active-high;
+ 	};
+ 
+-	wifi_pwrseq: wifi_pwrseq {
++	pwrseq_wifi: pwrseq_wifi@0 {
+ 		compatible = "mmc-pwrseq-simple";
++		pinctrl-names = "default";
++		pinctrl-0 = <&wifi_rst>;
+ 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+-		post-power-on-delay-ms = <200>;
++		post-power-on-delay-ms = <50>;
+ 	};
+ };
+ 
+@@ -124,9 +127,11 @@
+ &mmc1 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc1_pins_a>;
+-	vmmc-supply = <&reg_vcc_wifi>;
+-	mmc-pwrseq = <&wifi_pwrseq>;
++	vmmc-supply = <&reg_vcc3v3>;
++	vqmmc-supply = <&vdd_wifi>;
++	mmc-pwrseq = <&pwrseq_wifi>;
+ 	bus-width = <4>;
++	max-frequency = <16000000>;
+ 	non-removable;
+ 	status = "okay";
+ 
+@@ -136,9 +141,30 @@
+ 	 */
+ 	xr819: sdio_wifi@1 {
+ 		reg = <1>;
++		compatible = "xradio,xr819";
++		pinctrl-names = "default";
++		pinctrl-0 = <&wifi_wake>;
++		interrupt-parent = <&pio>;
++		interrupts = <6 10 IRQ_TYPE_EDGE_RISING>;
++		interrupt-names = "host-wake";
++		local-mac-address = [dc 44 6d c0 ff ee];
+ 	};
+ };
+ 
++&pio {
++	wifi_wake: wifi_wake {
++		pins = "PG10";
++		function = "gpio_in";
++    };
++};
++
++&r_pio {
++	wifi_rst: wifi_rst {
++		pins = "PL7";
++		function = "gpio_out";
++    };
++};
++
+ &mmc1_pins_a {
+ 	bias-pull-up;
+ };

recipes-kernel/linux/linux-mainline_4.16.13.bb

@@ -0,0 +1,32 @@
+SECTION = "kernel"
+DESCRIPTION = "Mainline Linux kernel"
+LICENSE = "GPLv2"
+LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
+
+inherit kernel
+
+require linux.inc
+
+# Since we're not using git, this doesn't make a difference, but we need to fill
+# in something or kernel-yocto.bbclass will fail.
+KBRANCH ?= "master"
+
+# Pull in the devicetree files into the rootfs
+RDEPENDS_${KERNEL_PACKAGE_NAME}-base += "kernel-devicetree"
+
+KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
+
+S = "${WORKDIR}/linux-${PV}"
+	
+SRC_URI[md5sum] = "86f56f586f35ac3a98e086dccfd2ff99"
+SRC_URI[sha256sum] = "6f0a7b3abd48eca3df5e29bfbcfc1c06dd2792f86d23cdb9ad37cf3e572df2e3"
+
+SRC_URI = "https://www.kernel.org/pub/linux/kernel/v4.x/linux-${PV}.tar.xz \
+        file://0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch \
+        file://defconfig \
+        "
+
+SRC_URI_append_orange-pi-zero += "\
+	file://0001-add-wifi-support.patch \
+	"

recipes-kernel/linux/linux-mainline_git.bb

@@ -1,26 +1,29 @@
 SECTION = "kernel"
 DESCRIPTION = "Mainline Linux kernel"
 LICENSE = "GPLv2"
-LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i)"
+LIC_FILES_CHKSUM = "file://COPYING;md5=bbea815ee2795b2f4230826c0c6b8814"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
 
 inherit kernel
 
-require recipes-kernel/linux/linux-dtb.inc
 require linux.inc
 
+# Since we're not using git, this doesn't make a difference, but we need to fill
+# in something or kernel-yocto.bbclass will fail.
+KBRANCH ?= "master"
+
 # Pull in the devicetree files into the rootfs
-RDEPENDS_kernel-base += "kernel-devicetree"
+RDEPENDS_${KERNEL_PACKAGE_NAME}-base += "kernel-devicetree"
 
 # Default is to use stable kernel version
 # If you want to use latest git version set to "1"
-DEFAULT_PREFERENCE = "-1" 
+DEFAULT_PREFERENCE = "-1"
 
 KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
 	
-# 4.5.0
-PV = "4.4+4.5.0.git${SRCPV}"
-SRCREV_pn-${PN} = "b562e44f507e863c6792946e4e1b1449fbbac85d"
+# v4.17-rc7
+PV = "v4.17-rc7+git${SRCPV}"
+SRCREV_pn-${PN} = "b04e217704b7f879c6b91222b066983a44a7a09f"
 
 SRC_URI = "git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git;protocol=git;branch=master \
         file://defconfig \

recipes-kernel/linux/linux-sunxi/0001-compiler-gcc-integrate-the-various-compiler-gcc-345-.patch

@@ -0,0 +1,276 @@
+From a66aaac889f09425ff0f3ddb27aca46ae02d6eea Mon Sep 17 00:00:00 2001
+From: Joe Perches <joe@perches.com>
+Date: Thu, 25 Jun 2015 15:01:02 -0700
+Subject: [PATCH] compiler-gcc: integrate the various compiler-gcc[345].h files
+
+As gcc major version numbers are going to advance rather rapidly in the
+future, there's no real value in separate files for each compiler
+version.
+
+Deduplicate some of the macros #defined in each file too.
+
+Neaten comments using normal kernel commenting style.
+
+Upstream-Status: Backport
+
+Signed-off-by: Joe Perches <joe@perches.com>
+Cc: Andi Kleen <andi@firstfloor.org>
+Cc: Michal Marek <mmarek@suse.cz>
+Cc: Segher Boessenkool <segher@kernel.crashing.org>
+Cc: Sasha Levin <levinsasha928@gmail.com>
+Cc: Anton Blanchard <anton@samba.org>
+Cc: Alan Modra <amodra@gmail.com>
+Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
+Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
+Signed-off-by: Jonathan Liu <net147@gmail.com>
+---
+ include/linux/compiler-gcc.h  | 120 ++++++++++++++++++++++++++++++++++++++++--
+ include/linux/compiler-gcc3.h |  23 --------
+ include/linux/compiler-gcc4.h |  74 --------------------------
+ 3 files changed, 116 insertions(+), 101 deletions(-)
+ delete mode 100644 include/linux/compiler-gcc3.h
+ delete mode 100644 include/linux/compiler-gcc4.h
+
+diff --git a/include/linux/compiler-gcc.h b/include/linux/compiler-gcc.h
+index 7970e31..727add9 100644
+--- a/include/linux/compiler-gcc.h
++++ b/include/linux/compiler-gcc.h
+@@ -97,10 +97,122 @@
+ #define __maybe_unused			__attribute__((unused))
+ #define __always_unused			__attribute__((unused))
+ 
+-#define __gcc_header(x) #x
+-#define _gcc_header(x) __gcc_header(linux/compiler-gcc##x.h)
+-#define gcc_header(x) _gcc_header(x)
+-#include gcc_header(__GNUC__)
++/* gcc version specific checks */
++
++#if GCC_VERSION < 30200
++# error Sorry, your compiler is too old - please upgrade it.
++#endif
++
++#if GCC_VERSION < 30300
++# define __used			__attribute__((__unused__))
++#else
++# define __used			__attribute__((__used__))
++#endif
++
++#ifdef CONFIG_GCOV_KERNEL
++# if GCC_VERSION < 30400
++#   error "GCOV profiling support for gcc versions below 3.4 not included"
++# endif /* __GNUC_MINOR__ */
++#endif /* CONFIG_GCOV_KERNEL */
++
++#if GCC_VERSION >= 30400
++#define __must_check		__attribute__((warn_unused_result))
++#endif
++
++#if GCC_VERSION >= 40000
++
++/* GCC 4.1.[01] miscompiles __weak */
++#ifdef __KERNEL__
++# if GCC_VERSION >= 40100 &&  GCC_VERSION <= 40101
++#  error Your version of gcc miscompiles the __weak directive
++# endif
++#endif
++
++#define __used			__attribute__((__used__))
++#define __compiler_offsetof(a, b)					\
++	__builtin_offsetof(a, b)
++
++#if GCC_VERSION >= 40100 && GCC_VERSION < 40600
++# define __compiletime_object_size(obj) __builtin_object_size(obj, 0)
++#endif
++
++#if GCC_VERSION >= 40300
++/* Mark functions as cold. gcc will assume any path leading to a call
++ * to them will be unlikely.  This means a lot of manual unlikely()s
++ * are unnecessary now for any paths leading to the usual suspects
++ * like BUG(), printk(), panic() etc. [but let's keep them for now for
++ * older compilers]
++ *
++ * Early snapshots of gcc 4.3 don't support this and we can't detect this
++ * in the preprocessor, but we can live with this because they're unreleased.
++ * Maketime probing would be overkill here.
++ *
++ * gcc also has a __attribute__((__hot__)) to move hot functions into
++ * a special section, but I don't see any sense in this right now in
++ * the kernel context
++ */
++#define __cold			__attribute__((__cold__))
++
++#define __UNIQUE_ID(prefix) __PASTE(__PASTE(__UNIQUE_ID_, prefix), __COUNTER__)
++
++#ifndef __CHECKER__
++# define __compiletime_warning(message) __attribute__((warning(message)))
++# define __compiletime_error(message) __attribute__((error(message)))
++#endif /* __CHECKER__ */
++#endif /* GCC_VERSION >= 40300 */
++
++#if GCC_VERSION >= 40500
++/*
++ * Mark a position in code as unreachable.  This can be used to
++ * suppress control flow warnings after asm blocks that transfer
++ * control elsewhere.
++ *
++ * Early snapshots of gcc 4.5 don't support this and we can't detect
++ * this in the preprocessor, but we can live with this because they're
++ * unreleased.  Really, we need to have autoconf for the kernel.
++ */
++#define unreachable() __builtin_unreachable()
++
++/* Mark a function definition as prohibited from being cloned. */
++#define __noclone	__attribute__((__noclone__))
++
++#endif /* GCC_VERSION >= 40500 */
++
++#if GCC_VERSION >= 40600
++/*
++ * Tell the optimizer that something else uses this function or variable.
++ */
++#define __visible	__attribute__((externally_visible))
++#endif
++
++/*
++ * GCC 'asm goto' miscompiles certain code sequences:
++ *
++ *   http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
++ *
++ * Work it around via a compiler barrier quirk suggested by Jakub Jelinek.
++ *
++ * (asm goto is automatically volatile - the naming reflects this.)
++ */
++#define asm_volatile_goto(x...)	do { asm goto(x); asm (""); } while (0)
++
++#ifdef CONFIG_ARCH_USE_BUILTIN_BSWAP
++#if GCC_VERSION >= 40400
++#define __HAVE_BUILTIN_BSWAP32__
++#define __HAVE_BUILTIN_BSWAP64__
++#endif
++#if GCC_VERSION >= 40800 || (defined(__powerpc__) && GCC_VERSION >= 40600)
++#define __HAVE_BUILTIN_BSWAP16__
++#endif
++#endif /* CONFIG_ARCH_USE_BUILTIN_BSWAP */
++
++#if GCC_VERSION >= 50000
++#define KASAN_ABI_VERSION 4
++#elif GCC_VERSION >= 40902
++#define KASAN_ABI_VERSION 3
++#endif
++
++#endif	/* gcc version >= 40000 specific checks */
+ 
+ #if !defined(__noclone)
+ #define __noclone	/* not needed */
+diff --git a/include/linux/compiler-gcc3.h b/include/linux/compiler-gcc3.h
+deleted file mode 100644
+index 37d4124..0000000
+--- a/include/linux/compiler-gcc3.h
++++ /dev/null
+@@ -1,23 +0,0 @@
+-#ifndef __LINUX_COMPILER_H
+-#error "Please don't include <linux/compiler-gcc3.h> directly, include <linux/compiler.h> instead."
+-#endif
+-
+-#if __GNUC_MINOR__ < 2
+-# error Sorry, your compiler is too old - please upgrade it.
+-#endif
+-
+-#if __GNUC_MINOR__ >= 3
+-# define __used			__attribute__((__used__))
+-#else
+-# define __used			__attribute__((__unused__))
+-#endif
+-
+-#if __GNUC_MINOR__ >= 4
+-#define __must_check		__attribute__((warn_unused_result))
+-#endif
+-
+-#ifdef CONFIG_GCOV_KERNEL
+-# if __GNUC_MINOR__ < 4
+-#   error "GCOV profiling support for gcc versions below 3.4 not included"
+-# endif /* __GNUC_MINOR__ */
+-#endif /* CONFIG_GCOV_KERNEL */
+diff --git a/include/linux/compiler-gcc4.h b/include/linux/compiler-gcc4.h
+deleted file mode 100644
+index 91b1aa8..0000000
+--- a/include/linux/compiler-gcc4.h
++++ /dev/null
+@@ -1,74 +0,0 @@
+-#ifndef __LINUX_COMPILER_H
+-#error "Please don't include <linux/compiler-gcc4.h> directly, include <linux/compiler.h> instead."
+-#endif
+-
+-/* GCC 4.1.[01] miscompiles __weak */
+-#ifdef __KERNEL__
+-# if __GNUC_MINOR__ == 1 && __GNUC_PATCHLEVEL__ <= 1
+-#  error Your version of gcc miscompiles the __weak directive
+-# endif
+-#endif
+-
+-#define __used			__attribute__((__used__))
+-#define __must_check 		__attribute__((warn_unused_result))
+-#define __compiler_offsetof(a,b) __builtin_offsetof(a,b)
+-
+-#if __GNUC_MINOR__ >= 3
+-/* Mark functions as cold. gcc will assume any path leading to a call
+-   to them will be unlikely.  This means a lot of manual unlikely()s
+-   are unnecessary now for any paths leading to the usual suspects
+-   like BUG(), printk(), panic() etc. [but let's keep them for now for
+-   older compilers]
+-
+-   Early snapshots of gcc 4.3 don't support this and we can't detect this
+-   in the preprocessor, but we can live with this because they're unreleased.
+-   Maketime probing would be overkill here.
+-
+-   gcc also has a __attribute__((__hot__)) to move hot functions into
+-   a special section, but I don't see any sense in this right now in
+-   the kernel context */
+-#define __cold			__attribute__((__cold__))
+-
+-#define __linktime_error(message) __attribute__((__error__(message)))
+-
+-/*
+- * GCC 'asm goto' miscompiles certain code sequences:
+- *
+- *   http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
+- *
+- * Work it around via a compiler barrier quirk suggested by Jakub Jelinek.
+- * Fixed in GCC 4.8.2 and later versions.
+- *
+- * (asm goto is automatically volatile - the naming reflects this.)
+- */
+-#if GCC_VERSION <= 40801
+-# define asm_volatile_goto(x...)	do { asm goto(x); asm (""); } while (0)
+-#else
+-# define asm_volatile_goto(x...)	do { asm goto(x); } while (0)
+-#endif
+-
+-#if __GNUC_MINOR__ >= 5
+-/*
+- * Mark a position in code as unreachable.  This can be used to
+- * suppress control flow warnings after asm blocks that transfer
+- * control elsewhere.
+- *
+- * Early snapshots of gcc 4.5 don't support this and we can't detect
+- * this in the preprocessor, but we can live with this because they're
+- * unreleased.  Really, we need to have autoconf for the kernel.
+- */
+-#define unreachable() __builtin_unreachable()
+-
+-/* Mark a function definition as prohibited from being cloned. */
+-#define __noclone	__attribute__((__noclone__))
+-
+-#endif
+-#endif
+-
+-#if __GNUC_MINOR__ > 0
+-#define __compiletime_object_size(obj) __builtin_object_size(obj, 0)
+-#endif
+-#if __GNUC_MINOR__ >= 4 && !defined(__CHECKER__)
+-#define __compiletime_warning(message) __attribute__((warning(message)))
+-#define __compiletime_error(message) __attribute__((error(message)))
+-#endif
+-- 
+2.10.0
+

recipes-kernel/linux/linux-sunxi_3.4.bb

@@ -12,7 +12,7 @@ SRCREV_pn-${PN} = "d47d367036be38c5180632ec8a3ad169a4593a88"
 MACHINE_KERNEL_PR_append = "a"
 
 SRC_URI += "git://github.com/linux-sunxi/linux-sunxi.git;branch=sunxi-3.4;protocol=git \
-        file://0001-compiler-gcc5.patch \
+        file://0001-compiler-gcc-integrate-the-various-compiler-gcc-345-.patch \
         file://0002-use-static-inline-in-ARM-ftrace.patch \
         file://0001-gcc5-fixes.patch \
         file://defconfig \

recipes-kernel/linux/linux.inc

@@ -1,11 +1,10 @@
 DESCRIPTION = "Linux Kernel"
 SECTION = "kernel"
 LICENSE = "GPLv2"
-LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
 
 INC_PR = "r0"
 
-inherit kernel siteinfo
+inherit kernel kernel-yocto siteinfo
 
 # Enable OABI compat for people stuck with obsolete userspace
 ARM_KEEP_OABI ?= "0"
@@ -16,12 +15,14 @@ CMDLINE_DEBUG ?= "loglevel=3"
 
 # Kernel bootlogo is distro-specific (default is OE logo).
 # Logo resolution (qvga, vga, ...) is machine-specific.
-LOGO_SIZE ?= '${@base_conditional("MACHINE_GUI_CLASS", "bigscreen", "vga", "qvga", d)}'
+LOGO_SIZE ?= '${@oe.utils.conditional("MACHINE_GUI_CLASS", "bigscreen", "vga", "qvga", d)}'
 # To use this, add file://${LOGO_SIZE}/logo_linux_clut224.ppm.bz2 or similar
 # to your kernel recipe, and then structure your logos for each resolution
 # accordingly.
 
 LOCALVERSION ?= ""
+KCONFIG_MODE ?= "alldefconfig"
+KMACHINE ?= "${MACHINE}"
 
 #kernel_conf_variable CMDLINE "\"${CMDLINE} ${CMDLINE_DEBUG}\""
 kernel_conf_variable() {
@@ -34,8 +35,11 @@ kernel_conf_variable() {
     fi
 }
 
+do_kernel_configme[depends] += "virtual/${TARGET_PREFIX}binutils:do_populate_sysroot"
+do_kernel_configme[depends] += "virtual/${TARGET_PREFIX}gcc:do_populate_sysroot"
+do_kernel_configme[depends] += "bc-native:do_populate_sysroot bison-native:do_populate_sysroot"
+
 do_configure_prepend() {
-    echo "" > ${B}/.config
     CONF_SED_SCRIPT=""
 
     #
@@ -111,9 +115,6 @@ do_configure_prepend() {
         kernel_conf_variable CMDLINE \"${CMDLINE_NFSROOT_USB} ${CMDLINE_DEBUG}\"
     fi
 
-    sed -e "${CONF_SED_SCRIPT}" \
-    < '${WORKDIR}/defconfig' >>'${B}/.config'
-
     yes '' | oe_runmake -C ${S} O=${B} oldconfig
 }
 

recipes-kernel/linux/linux_4.4.6.bb

@@ -1,24 +0,0 @@
-SECTION = "kernel"
-DESCRIPTION = "Mainline Linux kernel"
-LICENSE = "GPLv2"
-LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i)"
-
-inherit kernel
-
-require recipes-kernel/linux/linux-dtb.inc
-require linux.inc
-
-# Pull in the devicetree files into the rootfs
-RDEPENDS_kernel-base += "kernel-devicetree"
-
-KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
-
-S = "${WORKDIR}/linux-${PV}"
-	
-SRC_URI[md5sum] = "efc822dad2149e40cc908718a4fea1d3"
-SRC_URI[sha256sum] = "a3bccec4c28939355cd415672414583ecaf5531a87ddb44c9dc036aeacec577d"
-
-SRC_URI = "https://www.kernel.org/pub/linux/kernel/v4.x/linux-${PV}.tar.xz \
-        file://defconfig \
-        "

recipes-kernel/xradio-firmware/xradio-firmware.bb

@@ -0,0 +1,25 @@
+DESCRIPTION = "Xradio xr819 WiFi firmware"
+LICENSE = "CC0-1.0"
+LIC_FILES_CHKSUM = "file://${COMMON_LICENSE_DIR}/${LICENSE};md5=0ceb3372c9595f0a8067e55da801e4a1"
+
+PV = "1.0"
+PR = "r0"
+
+SRCREV = "8b4a4ed16f7f9d12e59ff2f9ceba3cc335374dbe"
+
+COMPATIBLE_MACHINE = "orange-pi-zero"
+
+SRC_URI = "git://github.com/armbian/build.git;protocol=https"
+
+S = "${WORKDIR}/git"
+
+do_install() {
+    install -d ${D}${base_libdir}/firmware/xr819
+    install -m 0644 ${S}/bin/firmware-overlay/xr819/boot_xr819.bin ${D}${base_libdir}/firmware/xr819/
+    install -m 0644 ${S}/bin/firmware-overlay/xr819/sdd_xr819.bin ${D}${base_libdir}/firmware/xr819/
+    install -m 0644 ${S}/bin/firmware-overlay/xr819/fw_xr819.bin ${D}${base_libdir}/firmware/xr819/
+}
+
+FILES_${PN} = "${base_libdir}/*"
+
+PACKAGES = "${PN}"

recipes-kernel/xradio/xradio.bb

@@ -0,0 +1,23 @@
+SUMMARY = "Xradio WiFi driver for orangepi-zero"
+LICENSE = "GPLv2"
+LIC_FILES_CHKSUM = "file://LICENSE;md5=a23a74b3f4caf9616230789d94217acb"
+
+inherit module
+
+PV = "0.1"
+PR = "r0"
+
+RDEPENDS_${PN} += "xradio-firmware"
+
+COMPATIBLE_MACHINE = "orange-pi-zero"
+
+SRCREV = "d649e5a78efdc56ecd0951e35ca60db175650232"
+
+SRC_URI = "git://github.com/fifteenhex/xradio.git;protocol=https \
+          "
+
+S = "${WORKDIR}/git"
+
+EXTRA_OEMAKE += "-C ${STAGING_KERNEL_DIR} M=${S}"
+
+KERNEL_MODULE_AUTOLOAD += "xradio_wlan"

recipes-support/sunxi-tools/sunxi-tools_git.bb

@@ -1,16 +1,14 @@
 DESCRIPTION = "Tools to help hacking Allwinner A10 and A20"
 
 LICENSE = "GPLv2+"
-LIC_FILES_CHKSUM = "file://COPYING;md5=b234ee4d69f5fce4486a80fdaf4a4263"
+LIC_FILES_CHKSUM = "file://LICENSE.md;md5=97bd67b5d0309e452b637f76e1c9a23c"
 
-PV = "1.0+git${SRCPV}"
-PKGV = "1.0+git${GITPKGV}"
-PR = "r3"
-SRCREV = "568c7a0e81fc5d52189710c6d832677aa8770b16"
+PR = "r0"
 
 DEPENDS += "libusb"
 
 SRC_URI = "git://github.com/linux-sunxi/sunxi-tools;protocol=git"
+SRCREV = "9a3d62aa0c820b3dd42ba3409b2043f4143683cd"
 
 S = "${WORKDIR}/git"
 
@@ -23,12 +21,12 @@ CFLAGS_class-native = "-std=c99 -D_POSIX_C_SOURCE=200112L -I./include"
 
 do_install() {
     install -d ${D}/${bindir}
-    install -m 755 ${S}/bootinfo ${D}/${bindir}
+    install -m 755 ${S}/sunxi-bootinfo ${D}/${bindir}
     install -m 755 ${S}/bin2fex ${D}/${bindir}
-    install -m 755 ${S}/fel ${D}/${bindir}
+    install -m 755 ${S}/sunxi-fel ${D}/${bindir}
     install -m 755 ${S}/fel-gpio ${D}/${bindir}
     install -m 755 ${S}/fex2bin ${D}/${bindir}
-    install -m 755 ${S}/fexc ${D}/${bindir}
-    install -m 755 ${S}/nand-part ${D}/${bindir}
-    install -m 755 ${S}/pio ${D}/${bindir}
+    install -m 755 ${S}/sunxi-fexc ${D}/${bindir}
+    install -m 755 ${S}/sunxi-nand-part ${D}/${bindir}
+    install -m 755 ${S}/sunxi-pio ${D}/${bindir}
 }