Update the layer compatibility information to indicate this layer is
compatible with "dunfell".
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Enable open source GPU support for Mali Utgard GPUs (lima driver) and
Mali Midgard and Bifrost GPUs (panfrost driver).
The support is enabled by:
- enabling DRM kernel CONFIGs
- enabling lima, panfrost and kmsro in Mesa
- disabling the specific mali driver overrides in sunxi-mali.inc
To enable open source mainline graphics support just add the following
line in your local.conf:
MACHINEOVERRIDES .= ":use-mailine-graphics"
Please note that some machines may need a bigger CMA value to be able to
start Weston. To do that, add e.g. "cma=128M" to the kernel parameters.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
According to:
https://www.kernel.org/category/releases.html
version 5.4 is a longterm release, so:
- add longterm 5.4 series at 5.4.18
- update longterm 4.19 series to 4.19.103
- update stable to 5.5.3
- remove rc, as it quickly gets out of date. rc users will likely build
kernel from master outside of OE anyway
- set 5.4 as the preferred version for linux-mainline
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Add support for AMPAK 6212A module:
1) install kernel module
2) install firmware
3) create the required symlink with the AP6212 NVRAM file
Enable the support in the boards with the module, according to:
https://linux-sunxi.org/Table_of_Allwinner_based_boards
The link creation with compatible name works on kernels >= 5.0.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Remove pointless U-Boot PREFERRED_VERSION, as meta-sunxi no longer
provides its own u-boot recipe.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
In the latest OE, this file has been renamed. Since this board is
ARMv8-A, we should use the armv8-a config instead of the armv8 config.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
This has been assigned a value containing a typo since 2015, my
assumption is that this is not used and hence we can simply drop
it. The typo is that the address contains a 'O' character instead
of '0', the last one is a zero.
Either way the kernel.bbclass will set a default value, that is:
UBOOT_LOADADDRESS ?= "${UBOOT_ENTRYPOINT}"
Signed-off-by: Mirza Krak <mirza.krak@northern.tech>
v2017.03 no longer exists and produces warnings if set as preferred:
NOTE: Resolving any missing task queue dependencies
NOTE: preferred version v2017.03% of u-boot not available (for item virtual/bootloader)
NOTE: versions of u-boot available: 1:2018.01 2:v2018.03+gitAUTOINC+f95ab1fb6e
NOTE: preferred version v2017.03% of u-boot not available (for item u-boot-dev)
NOTE: versions of u-boot available: 1:2018.01 2:v2018.03+gitAUTOINC+f95ab1fb6e
NOTE: preferred version v2017.03% of u-boot not available (for item u-boot)
NOTE: versions of u-boot available: 1:2018.01 2:v2018.03+gitAUTOINC+f95ab1fb6e
Signed-off-by: Mirza Krak <mirza.krak@northern.tech>
We have devicetree and u-boot configs for the nanopi-neo-air, so add
them. As a basic test, this boots correctly on my nanopi-neo-air.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Orange Pi Zero Plus2 board is based on AllWinner H5 SoC.
For more details on its hardware see linux-sunxi wiki:
http://linux-sunxi.org/Xunlong_Orange_Pi_Zero_Plus_2
This patch enables basic support for orange-pi-zero-plus2 board:
- mainline kernel 4.14.2
- mainline u-boot 2017.11
- dts kernel patch that fixes boot from SD card
- dts kernel patch enabling AP6212 WiFi/BT chip
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Add support of sun50i SoC family to u-boot recipe:
- move SPL_BINARY to sunxi.inc and sunxi64.inc
-- different SoC families have different SPL_BINARY names
- create separate boot.cmd files for arm and aarch64
-- different kernel image types require different boot commands
- add atf-sunxi dependency
-- u-boot for aarch64 needs ATF BL31 binary
- add do_compile_sun50i[depends]
-- make sure that BL31 binary is already deployed before u-boot build
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
