This patch corrects the mio and pll configuration registers for using usb3
on the kd240 starter kit. Without this patch, the usb3 to sd card bridge does
not initialize correctly and u-boot is unable to find the OS located on the
kd240 starter kit sd card.
In addition, this patch correctly configures mio76 and mio77 as gpio pins
which are used as reset gpio pins on the kd240 starter kit.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20240604083854.2033917-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
On Kria when board starts from Image A or Image B partition multiboot
register is already setup to that location. When reset command is called
board is issuing soft reset which start SW at already used location (offset
of multiboot * 32k).
But board should continue to run from multiboot offset 0 (start of QSPI)
and call early bootloader every reboot that's why clear multiboot register
to 0 by default to go that route all the time.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/edaf714a778bdd7447533a77b3455e4fd623f9da.1717420131.git.michal.simek@amd.com
SOC can boot out of the device which is not accessible from APU and running
this is detected as a warning, as the device is not accessible.For example
getting below warning when the boot mode is OSPI and OSPI is not enabled in
device tree.
Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)
Ignoring the prioritization of the boot device which driver is not enabled
and continue with the default boot_targets. Recommendation is to use custom
boot_targets via environment file as is done for example for Kria via
zynqmp_kria.env file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8b7cca5c7b84cb4854104e0c48f8aa63c4ec5ace.1715322156.git.michal.simek@amd.com
Once the environment was saved, the current multiboot image information
became unreachable. When dealing with firmware updates, this information
is necessary alongside the saved environment to know the booted image.
Move the multiboot environment set operation before the saved environment
check to ensure this information is always available.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240529100107.137159-1-kory.maincent@bootlin.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The zynqmp cmds.c is currently tied to the board but the commands
contained within are more closely tied to the architecture. To
allow usage of those commands when the architecture is ZynqMP but
the board is not, this change moves the cmds into the arch/ tree.
The source file is renamed to zynqmp.c to reflect the command name
as well.
Signed-off-by: Charlie Johnston <charlie.johnston@loftorbital.com>
Link: https://lore.kernel.org/r/20240410195008.405061-2-charlie.johnston@loftorbital.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Boards which have for example MAC address in eeprom but not in Xilinx
format (legacy or FRU) could reference it via nvmem cells.
For example:
&gem0 {
nvmem-cells = <&mac>;
nvmem-cell-names = "mac-address";
};
&eeprom {
#address-cells = <1>;
#size-cells = <1>;
mac: mac-address@f0 {
reg = <0xf0 6>;
};
};
For getting it work above DT changes are required but also CONFIG_NVMEM
should be enabled. That's why enable it by default in generic defconfigs
to be able to use it directly by changing DT only.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9c8ee7a4c7a16367438a92a4c9581bac9d968f84.1712815454.git.michal.simek@amd.com
Add tests for booting image using tftpboot/pxe boot commands, tftpboot
boot case loads the FIT image into DDR and boots using bootm command
whereas pxe boot cases downloads the pxe configuration file from the
TFTP server and interprets it to boot the images mentioned in the pxe
configurations file.
This test relies on boardenv_* containing configuration values including
the parameter 'pattern'. tftpboot/pxe boot cases boots the Linux till the
boot log pattern value is matched. For example, if the parameter
'pattern' is defined as 'login:', it will boot till login prompt.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Tested-by: Tom Rini <trini@konsulko.com>
Executing a u-boot command may raise an error or extra bad pattern,
beyond the default bad patterns. Providing a way to enable the console
output error check in test.
For example, description for OS boot test:
import re
check_type = 'kernel_boot_error'
check_pattern = re.compile('ERROR -2: can't get kernel image!')
with u_boot_console.enable_check(check_type, check_pattern):
u_boot_console.run_command('<boot command>')
Signed-off-by: Love Kumar <love.kumar@amd.com>
commit dfeb4f0d79 ("cmd: bcb: extend BCB C API to allow read/write the fields")
introduced the bcb_get() function.
When CONFIG_CMD_BCB=n, that function is stubbed.
The stubbed function has a wrong prototype: value_size arg is missing.
Add the missing argument to fix build when CONFIG_CMD_BCB=n.
Fixes: dfeb4f0d79 ("cmd: bcb: extend BCB C API to allow read/write the fields")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Dmitrii Merkurev <dimorinny@google.com>
Reviewed-by: Julien Masson <jmasson@baylibre.com>
Allow extraction of zstd-compressed images from FIT using imxtract
command. This is especially useful when one has to load an image via
some interface (e.g. SPI) rather that just to the memory.
Signed-off-by: Dmitry Gerasimov <di.gerasimov@gmail.com>
When bcmgenet complete to write Rx buffer with the DMA,
some U-Boot commands write data to the buffer directly.
Those write data will become dirty in CPU cache.
After this driver calls free_pkt to the buffer,
the buffer is assigned as the future Rx buffer.
At some point, if bcmgenet writes to a buffer with DMA
and CPU cache flushes dirty data to the buffer,
the buffer is corrupted.
This patch calls flush_dcache_range in free_pkt
to immediately flush the data written by U-Boot command
and prevent data corruption.
This issue can be reproduced using wget on Raspberry Pi4.
If wget receives data larger than
RX_BUF_LENGTH * RX_DESCS = 2048 * 256 bytes,
it will timeout due to data corruption.
In addition, if LOG_DEBUG is enabled in net/tcp.c,
the following error log is output.
TCP RX TCP xSum Error
Signed-off-by: Yasuharu Shibata <yasuharu.shibata@gmail.com>
All ARCH_K3 platforms need about of 2MB of malloc space post
reallocation. Since, this space is allocated from SDRAM, provide a
generous 2MB space by default.
Platforms requiring more than 2MB can override in defconfig as needed.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The default DM firmware path is non-optional as of now. Make it
optional so that users that choose to provide DM via TI_DM argument
instead of BINMAN_INDIRS can do so without build errors.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
According to [0], raw access to mmc should not have mmcpart in the
entry. This was fixed in k3_dfu_combined.env but k3_dfu.env had been
overlooked.
[0] doc/usage/dfu.rst
Fixes: 53b406369e ("DFU: Check the number of arguments and argument string strictly")
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
MAIN_PLL0 has a flag set in DM (Device Manager) that removes its
capability to re-initialise clock frequencies. A72 CPU clock (GTC) and
RGMII has MAIN_PLL3 as their parent which does not have this flag. While
RGMII needs re-initialization to default frequency to be able to get
250MHz with its divider, GTC can not get its required 200MHz with its
dividers. Thus move GTC clock parent on J721S2 from MAIN_PLL3_HSDIV1 to
MAIN_PLL0_HSDIV6. This was already done on CPTS node in kernel which was
similarly affected (linked).
Link: https://lore.kernel.org/all/20230605110443.84568-1-n-francis@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Let users configure default auto-negotiation timeout via Kconfig
instead of specifying it in board configuration headers. This is
the first step toward converting this to Kconfig fully, so far the
legacy PHY_ANEG_TIMEOUT in configuration headers takes precedence.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
R5 being a 32-bit processor can't understand the 64-bit mapping being
done in ospi node. Override the ospi node for 32-bit register ranges and
the fss node ( the parent node of ospi ) to map the ranges for the
updated child node correctly.
Reviewed-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
On DTR capable flashes like Micron Xcella the writes cannot start or end
at an odd address in DTR mode. Extra 0xff bytes need to be prepended or
appended respectively to make sure both the start and end addresses are
even.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jonathan Humphreys <j-humphreys@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Pull request efi-next-20240611
UEFI:
* Allow specifying a device-tree in an EFI load option
using the efidebug or eficonfig command.
* Let the EFI boot manager fall back to an OS provided device-tree
if no device-tree is specified.
As we now also store device-tree device-paths in load options rename
struct efi_initrd_dp to efi_lo_dp_prefix.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If no device-tree is specified, try to load a device-tree from the boot
device use the $fdtfile concatenated to either of the paths '/dtb/', '/',
'/dtb/current/'.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For finding distro supplied device-trees we need to know from which device
we are booting. This can be identified via the device-path of the binary.
Up to now efi_dp_from_lo() only could return the initrd or fdt device-path.
Allow returning the binary device-path, too.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We allow to specify the triple of binary, initrd, and device-tree in boot
options.
Add the code to actually load the specified device-tree.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We already support creating a load option where the device-path
field contains the concatenation of the binary device-path and
optionally the device path of the initrd which we expose via the
EFI_LOAD_FILE2_PROTOCOL.
Allow to append another device-path pointing to the device-tree
identified by the device-tree GUID.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We already support creating a load option where the device-path
field contains the concatenation of the binary device-path and
optionally the device path of the initrd which we expose via the
EFI_LOAD_FILE2_PROTOCOL.
Allow to append another device-path pointing to the device-tree
identified by the device-tree GUID.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Allow appending a device-path to a device-path that contains an end node
as separator. We need this feature for creating boot options specifying
kernel, initrd, and dtb.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
I've encountered a problem when compiling the 'examples/api' directory for ARM64 in U-boot. The problem lies in the assembly code in 'examples/api/crt0.S' where the current CONFIG_ARM code is only 32-bit. When targeting ARM64, a 64-bit version is necessary.
I have proposed a fix by including a 'CONFIG_ARM64' section in the assembly code as shown below. These changes have been check via https://github.com/u-boot/u-boot/pull/538.
Feedback is welcome.
Signed-off-by: Kalen Brunham <kalen.brunham@intel.com>
Quote from [1]:
"For devices launching with Android 13, the generic ramdisk is removed
from the boot image and placed in a separate init_boot image.
This change leaves the boot image with only the GKI kernel."
While at it, update wrong error handling message when vendor_boot
cannot be loaded.
[1]: https://source.android.com/docs/core/architecture/partitions/generic-boot
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The boot_ramdisk and vendor_ramdisk must be both concatenated together.
Without this change, Android root is missing some of the necessary tools
to complete virtual AB OTA.
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
commit 6e2228fb05 ("Merge patch series "Clean up arm linker scripts")
was cleaning up linker scripts for armv7 and v8 but was leaving
_end and __secure_stack_start/end.
commit d0b5d9da5d ("arm: make _end compiler-generated")
was moving _end to be compiler generated. _end is defined as c variable
in its own section to force the compiler emit relative a reference.
However, defining those in the linker script will do the same thing
since [0].
So let's remove the special sections from the linker scripts, the
variable definitions from sections.c and define them as a symbols.
It's worth noting that _image_binary_end symbol is now redundant and
can be removed in the future.
- SPL
The .end section has been removed from the new binary
[ 5] .end
PROGBITS 00000000fffdf488 000000000002f488 0
0000000000000000 0000000000000000 0 1
[0000000000000003]: WRITE, ALLOC
$~ bloat-o-meter kria_old/spl/u-boot-spl krina_new/spl/u-boot-spl
add/remove: 0/0 grow/shrink: 0/0 up/down: 0/0 (0)
Function old new delta
Total: Before=115980, After=115980, chg +0.00%
$~ readelf -sW kria_old/u-boot kria_new/u-boot | grep -w _end
12047: 000000000813a0f0 0 OBJECT GLOBAL DEFAULT 11 _end
12047: 000000000813a118 0 NOTYPE GLOBAL DEFAULT 11 _end
$~ readelf -sW kria_old/spl/u-boot-spl kria_new/spl/u-boot-spl | grep -w _end
1605: 00000000fffdf488 0 OBJECT GLOBAL DEFAULT 5 _end
1603: 00000000fffdf498 0 NOTYPE GLOBAL DEFAULT 4 _end
$~ readelf -sW old/u-boot new/u-boot | grep -w _end
8847: 0000000000103710 0 OBJECT GLOBAL DEFAULT 11 _end
8847: 0000000000103738 0 NOTYPE GLOBAL DEFAULT 11 _end
$~ readelf -sW old_v7/u-boot new_v7/u-boot | grep -w _end
10638: 000da824 0 OBJECT GLOBAL DEFAULT 10 _end
10637: 000da84c 0 NOTYPE GLOBAL DEFAULT 10 _end
- For both QEMU instances
$~ bloat-o-meter old/u-boot new/u-boot
add/remove: 0/0 grow/shrink: 1/0 up/down: 20/0 (20)
Function old new delta
version_string 50 70 +20
Total: Before=656915, After=656935, chg +0.00%
[0] binutils commit 6b3b0ab89663 ("Make linker assigned symbol dynamic only for shared object")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When decompressing, it's possible that the algorithm only performs
a partial decompression.
This usually happens when CONFIG_SYS_BOOTM_LEN is too small for
the uncompressed image.
When that happens, image_decomp() returns an error and *load_end == load.
The error is then handled by handle_decomp_error().
handle_decomp_error() expects the number of uncompressed bytes in
uncomp_size but receives *load_end - load == load - load == 0.
Because of this, handle_decomp_error does not report the expected
"Image too large: increase CONFIG_SYS_BOOTM_LEN" error message.
Modify the image_decomp() logic to always report the decompressed size,
even when a partial decompression happened.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
