Hardkernel ODROID-M1S is a single board computer with a RK3566 SoC,
a slightly modified version of the RK3566 SoC.
Features tested on a ODROID-M1S 8GB v1.0 2023-08-10:
- SD-card boot
- eMMC boot
- PCIe/NVMe
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Based on the ROCK 3 Model C / Pine64 Quartz64-B and Jianfeng Liu's kernel DT.
Tested with a OrangePi 3B 4GB v1.1:
- SD-card boot
- eMMC boot
- SPI Flash boot
- chip is XMC XM25QU128CWIQ, not W25Q256JWEIQ listed in schematics
- PCIe/NVMe
- USB is untested
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
The PineNote is an e-ink tablet by PINE64. It is built around a Rockchip
RK3566 SoC and has the following specifications:
- 4GB LPDDR4
- 128GB eMMC
- 10.3" 1404x1872 e-ink display
This board is very similar to other RK356x-based boards, with the
exception that its download-mode "key" (actually a Hall sensor) is on
ADC channel 0 instead of 1.
As such, this patch is heavily based on the evb_3568 board
implementation with the addition of a simple board setup code, meant to
account for the above difference.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Add a minimal generic RK3588S/RK3588 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3588S/RK3588 boards that follow reference board design.
Also fix the alphabetical order of RK3588 boards listed in Makefile and
documentation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
Link to v1: https://patchwork.ozlabs.org/patch/1893667/
Similar to RK35xx the BootRom in RK3328 can read all data and look for
idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Replace the rockchip,cryptov1-rng compatible with compatibles used in
the linux device tree for RK3288, RK3328 and RK3399 to ease sync of SoC
device tree from linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When RK3328 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there is a fallback to
read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card will fail:
U-Boot SPL 2024.04-rc1 (Feb 05 2024 - 22:18:22 +0000)
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove &gmac2io to
support reset of onboard ethernet PHYs.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Update defconfig for rk3328-nanopi-r2* boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove &gmac2io to
support reset of onboard ethernet PHYs.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Change to use a common FIT load order, same-as-spl > SD-card > eMMC on
RK3328 boards. Only EVB and Radxa ROCK Pi E is affected by this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566
SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64,
commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64
PineTab2").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://patchwork.ozlabs.org/patch/1895031/
This commit enables support for DM_SERIAL in the vexpress_ca9x4 boards.
When running the board with the DM_SERIAL driver, the board ran out of
memory in SPL when initialising the DM serial driver.
Thus this required an increase in the pre-allocated SRAM memory. I did
increase it to 0x800, and it now works graciously.
It could probably be set lower, but I do not see any reason not to use the
available SRAM at this point.
Also adds stdout-path to the 'chosen' node in the device tree.
Signed-off-by: Ole P. Orhagen <ole.orhagen@northern.tech>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Writing to eMMC using HS200 mode work more reliably then other modes on
RK356x boards.
Add device tree props and enable Kconfig options for eMMC HS200 mode on
the generic RK3566/RK3568 board. Also enable the pinctrl driver in SPL
and add missing rk3568-generic.dtb to Makefile.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Testing has shown that writing to eMMC using DDR52 mode does not seem to
work on RK356x and RK3588 boards.
A simple test of writing a single block to e.g. sector 0x4000 fails:
# Rescan using DDR52 mode
=> mmc rescan 4
# Write a single block to sector 0x4000 fails with ERROR
=> mmc write 20000000 4000 1
With the MMC_SPEED_MODE_SET Kconfig option enabled.
Fix this by removing the mmc-ddr-1_8v prop from sdhci nodes in affected
board u-boot.dtsi files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove unnecessary status props from rk35xx u-boot.dtsi files, regular
device tree files or default value already enable the affected nodes.
Also reorder bootph-pre-ram and clock-frequency props alphabetically in
rk3588s-u-boot.dtsi uart2 node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a default u-boot,spl-boot-order prop to rk3588s-u-boot.dtsi and
remove the prop from board u-boot.dtsi files using the default value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3588 device tree from linux v6.7.
Also drop the rockchip,rk3568-dwc3 compatible now that dwc3-generic
driver support the rockchip,rk3588-dwc3 compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Move uart2 bootph-pre-ram and clock-frequency props from board to SoC
u-boot.dtsi. Regular board device tree already enables the uart2 node,
so status prop is dropped from u-boot.dtsi file.
Also remove unnecessary stdout-path = &uart2, regular board device tree
already provide a stdout-path = "serial2:" value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync linux dts files for rv1126 boards from linux v6.8-rc1 tag. Includes
the newly added dts for Sonoff iHost.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some 32-bit SoCs can use SCP firmware to implement additional PSCI
functionality, such as system suspend. In order to load this firmware
from SPL, we need to generate and use a FIT instead of a legacy image.
Adjust the binman FIT definition so it does not rely on TF-A BL31, as
this is not used on 32-bit SoCs. Instead, after loading the firmware,
U-Boot proper is executed directly. This requires to provide an
entry point property for the U-Boot image node, which confuses some
loaders like sunxi-fel, so protect that to only be used if we have no
BL31.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: filter U-Boot entry point property]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is easier to read than the #ifdef staircase, provides better
visibility into the memory map (alongside the other Kconfig
definitions), and allows these addresses to be reused from code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This is a Chinese TV box based on Allwinner H618 SoC.
The DRAM parameters were derived from the values found in a firmware update.
Signed-off-by: Nick Alilovic <nickalilovic@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.8-rc1.
This time only small changes in the existing files, but five new boards
got added, which opens the door for their respective defconfig files.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Allow i.MX8M Plus DHCOM to operate in overdrive mode.
- Allow i.MX8M Plus eDM SBC to operate in overdrive mode.
- Enable the 'kaslrseed' command on DH i.MX8M Plus DHCOM.
- Select LTO by default on i.MX8M.
- Convert pico-dwarf/hobbit-imx6ul to CONFIG_DM_SERIAL.
- Fix 'reset' command on wandboard.
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The reserved space is extended to 32MB in Linux kernel because
additional space is needed for authorization execution of JIC/RBF file.
U-Boot required to align with Linux.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Port from Linux v6.7-rc4. Should not hurt U-Boot but makes diffing
easier and allows referencing node names in board dts.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Without correct SERDES MUX and Lane control settings
USB0 will be broken. Set the MUX and Lane control devices
to be auto probed so they are configured correctly.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Without correct SERDES MUX and Lane control settings
USB0 will be broken. Set the MUX and Lane control devices
to be auto probed so they are configured correctly.
Fixes: 69b19ca67b ("arm: dts: k3-j721e: Sync with v6.6-rc1")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Add CMDLINE dependecy for CMD_STM32KEY
STM32MP1:
---------
Set stdio to serial on DH STM32MP15xx DHSOM
Fix reset for usart1 in scmi configuration
STM32MP2:
---------
Add BSEC and OTP support for STM32MP25
Fix CONFIG_STM32MP25X flag usage
Add BSEC support to STM32MP25 SoC family with SoC information:
- RPN = Device part number (BSEC_OTP_DATA9)
- PKG = package data register (Bits 2:0 of BSEC_OTP_DATA122)
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
In SCMI configuration, usart1 is secure, so all its resources are secured
(clock and reset) and can't be set/unset by non-secure world but by OP-TEE.
Fixes: 6cccc8d396 ("ARM: dts: stm32: add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
