As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Upstream Linux commit 87dd96111b0b.
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-5-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Martyn Welch <martyn.welch@collabora.com> says:
This series adds DFU support for TI AM62 SK and beagleplay boards.
I have picked this series up from Sjoerd due to time constraints.
Since the last revision:
* Removed dwc3 mode setting in favour of reinstating forced peripheral
mode for usb0
* Use of config fragments for both r5 and a53 DFU configuration to
reduce duplication
* Typographical improvements to documentation
We plan to also submit the dts changes to linux so that those can be
dropped again in the near future (hopefully)
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for a vbus-supply regulator specified in devicetree. This
provides generic support to avoid hardcoded GPIO configuration in board
init code.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Like Rockchip RK3328 and RK3568, the RK3588 also have a single node to
represent the glue and ctrl for USB 3.0.
Use rk_ops as driver data to select correct ctrl node for RK3588 DWC3.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
Directly including asm-generic/io.h may break build because it will
cause redefenition of generic io macros if linux/io.h gets included
later, hence replace it with direct include of linux/io.h
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The usb_gadget_handle_interrupts() is no longer used anywhere,
replace the remaining uses with dm_usb_gadget_handle_interrupts()
which takes udevice as a parameter.
Some of the UDC drivers currently ignore the index parameter altogether,
those also ignore the udevice and have to be reworked. Other like the
dwc3_uboot_handle_interrupt() had to be switched from index to udevice
look up to avoid breakage.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3
Signed-off-by: Marek Vasut <marex@denx.de>
The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Also remove setting phy->dev to NULL now that generic_phy_get_by_name()
properly initialize phy->dev to NULL.
Fixes: 142d50fbce ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The original logic always enables USB_DR_MODE_HOST operation mode in
dwc3_layerscape_bind() in u-boot. Prevent choosing USB_DR_MODE_HOST
operation mode if USB_HOST is not enabled.
Fixes: 2b0b51d0be ("usb: dwc3: add layerscape support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
In the usb/dwc3-layerscape driver the first option should be renamed
to the latter as well. Do it.
Fix original logic in dwc3_layerscape_bind() - do not enable
Fixes: 333e4a621d ("Rename SPL_USB_HOST_SUPPORT to SPL_USB_HOST")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
As ulpi_reset gpio is now optional, we need to check it when doing
the 'dwc3_generic_remove' function. Check if it is declared before
accessing the ulpi_reset.
Fixes: 237d1f60b1 ("usb: dwc3: Use the devm_gpiod_get_optional()
API for reset gpio")
Reported-by: Thomas Nizan <tnizan@witekio.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Like Rockchip RK3568, the RK3328 also have single node to
represent the glue and ctrl for USB 3.0.
So, use the driver data to use single ctrl for RK3328 DWC3.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3568 share glue and ctrl in a single node. Use glue_get_ctrl_dev to
return the glue node as the ctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When dr_mode is peripheral or otg and U-Boot has not been built with
DM_USB_GADGET support, booting such device may end up with:
dwc3_glue_bind_common: subnode name: usb@fcc00000
Error binding driver 'dwc3-generic-wrapper': -6
Some drivers failed to bind
initcall sequence 00000000effbca08 failed at call 0000000000a217c8 (err=-6)
### ERROR ### Please RESET the board ###
Instead fail gracfully with ENODEV to allow board continue booting.
dwc3_glue_bind_common: subnode name: usb@fcc00000
dwc3_glue_bind_common: unsupported dr_mode 3
Also use CONFIG_IS_ENABLED(USB_HOST) and change switch to if statements
to improve readability of the code.
Fixes: 446e3a205b ("dwc3-generic: Handle the PHYs, the clocks and the reset lines")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
The current error check for device_find_first_child is not working as
expected, the documentation for device_find_first_child mention:
@devp: Returns first child device, or NULL if none
Return: 0
Change to return early when there is no child node to avoid any possible
null pointer dereference.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
GPIOD_ACTIVE_LOW is not enough to configure a GPIO as an output, we need
GPIOD_IS_OUT as well.
Fixes: b252d79b09 ("usb: dwc3: Add support to reset usb ULPI phy")
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Imply means you can turn off the option and expect things to work
- "it's a good idea to have X enabled" is when to use imply
- "you must have X for Y to work" is when to use select
Use "select" here.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Make sure the PHY subsystem is activated for the uniphier DWC3 glue
logic, as it depends on PHY implementation there.
Signed-off-by: Marek Vasut <marex@denx.de>
dwc3-uniphier depends on xhci-dwc3 framework, however, it is preferable
to use dwc3-generic.
This driver calls the exported dwc3-generic functions and redefine
the SoC-dependent operations to fit dwc3-generic.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add the size of regs property to the glue structure to correctly
specify the register region to map.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to allow external SoC-dependent glue drivers to use dwc3-generic
functions, push the glue structures and export the functions to a header
file.
The exported structures and functions are:
- struct dwc3_glue_data
- struct dwc3_glue_ops
- dwc3_glue_bind()
- dwc3_glue_probe()
- dwc3_glue_remove()
The SoC-dependent glue drivers can only define their own wrapper driver
and specify these functions. The drivers can also add their own compatible
strings and configure functions.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Same as the reset cotnrol, should add a clock initialization in child DT
node, if the glue node doesn't have any clocks.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The most of devicetree has the following USB node structure.
The controller node is placed as a child node of the glue node.
Current dwc3-generic driver works on this premise.
glue {
/* glue node */
usb {
/* controller node */
};
};
However, UniPhier original devicetree has the following USB node structure.
The controller node is separately placed from the glue node.
usb {
/* controller node */
};
glue {
/* glue node */
};
In dwc_glue_bind(), this patch provides .glue_get_ctrl_dev() callback to
get such a controller node and binds the driver related to the node.
If this callback isn't defined, dwc_glue_bind() looks for the controller
nodes from the child nodes, as before.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
There are currently four disparate placement possibilities of DWC3
reference clock phandle in SoC DTs:
- in top level glue node, with generic subnode without clock (ZynqMP)
- in top level generic node, with no subnode (i.MX8MQ)
- in generic subnode, with other clock in top level node (i.MX8MP)
- in both top level node and generic subnode (Rockchip)
Cover all the possibilities here by looking into both nodes, start
with the top level node as that seems to be used in majority of DTs
to reference the clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
As the "reset-gpios" property is optional, don't return the
error and just skip the gpio reset sequence.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
arch/mach-meson has some custom usb logic, in particular:
* on board_usb_init(), we force USB_DR_MODE_PERIPHERAL
* on board_usb_cleanup(), we force USB_DR_MODE_HOST
With DM_USB_GADGET=y, board_usb_init/cleanup() are no
longer used when we call usb_gadget_initialize().
Instead, the generic (from udc-uclass) initialization/release is
called, which itself calls the controller driver's probe()/remove().
Therefore, enabling DM_USB_GADGET=y will mean that this mode
switching will break.
To prepare for enabling DM_USB_GADGET, perform the mode switching
when the "amlogic,meson-g12a-usb" (dwc2) driver is
probed()/removed() instead.
This is achieved via the glue driver, which gets notified each time one
of its children is probed()/removed.
Note: this change should be harmless without DM_USB_GADGET=y
because the amlogic-g12a-usb driver is not probed via driver model.
Thanks for Mattijs for the original work at [1].
[1] https://lore.kernel.org/all/20221024-meson-dm-usb-v1-1-2ab077a503b9@baylibre.com/
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230117-u-boot-usb-gxl-otg-dm-v1-1-2853f6d75b06@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
arch/mach-meson has some custom usb logic, in particular:
* on board_usb_init(), we force USB_DR_MODE_PERIPHERAL
* on board_usb_cleanup(), we force USB_DR_MODE_HOST
With DM_USB_GADGET=y, board_usb_init/cleanup() are no
longer used when we call usb_gadget_initialize().
Instead, the generic (from udc-uclass) initialization/release is
called, which itself calls the controller driver's probe()/remove().
Therefore, enabling DM_USB_GADGET=y will mean that this mode
switching will break.
To prepare for enabling DM_USB_GADGET, perform the mode switching
when the "amlogic,meson-g12a-usb" (dwc2) driver is
probed()/removed() instead.
This is achieved via the glue driver, which gets notified each time one
of its children is probed()/removed.
Note: this change should be harmless without DM_USB_GADGET=y
because the amlogic-g12a-usb driver is not probed via driver model.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221024-meson-dm-usb-v1-1-2ab077a503b9@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Drop support for quickly deprecated DT property "snps,ref-clock-period-ns"
to prevent its proliferation.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
