Setting CONFIG_ENV_ADDR to something other than 0 stops gd->env_addr
from being allocated dynamically. When the environment is in SPI we need
it to be allocated as we can't use a direct memory mapped address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Fix build failure, it used to get this implicitly through common.h
until f7ae49fc4f (common: Drop log.h from common header).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Heiko Schocher <hs@denx.de>
Somewhere between v2020.04 and v2020.07 the mpc8xxx_spi driver broke,
I'm guessing due to this hunk
@@ -559,6 +560,8 @@ int dm_gpio_set_dir_flags(struct gpio_desc *desc, ulong flags)
if (ret)
return ret;
+ /* combine the requested flags (for IN/OUT) and the descriptor flags */
+ flags |= desc->flags;
ret = _dm_gpio_set_dir_flags(desc, flags);
from commit 695e5fd546 ("gpio: update dir_flags management"). But
the blame is mostly on the driver itself which seems rather confused:
The chip select gpios are requested with GPIOD_ACTIVE_LOW, but then in
each activate/deactivate, dm_gpio_set_dir_flags() is called with
merely GPIOD_IS_OUT, and then the driver call set_value(0) for
activate.
That used to work, but with the above hunk, the ACTIVE_LOW setting
from the request becomes persistent, so the gpio driver ends up being
asked to set the value to 1 in mpc8xxx_spi_cs_activate().
So drop the dm_gpio_set_dir_flags() calls in the activate/deactivate
functions, and use a value of 1 to mean "logically enabled".
Ideally, I think we should also drop the GPIOD_ACTIVE_LOW from the
request and make it up to the list of gpio cs in DT to indicate
whether that CS is enabled when driven low (as is of course usually
the case), but that requires changing
arch/powerpc/dts/gdsys/gazerbeam-base.dtsi among others, and I don't
have that hardware to test on. I have, however, tested our
own (mpc8309-based) hardware with this change, and I have also tested
that removing the GPIOD_ACTIVE_LOW from the request and updating our
DT as
- gpios = <&spisel 0 0>;
+ gpios = <&spisel 0 GPIO_ACTIVE_LOW>;
still works.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add a missing memset to acpi_create_spcr().
The other acpi_create_xxxx() functions perform a memset on their
structures, acpi_create_spcr() does not and as a result the contents of
this table are partly uninitialized (and thus random after every reset).
Fixes: b288cd9600 ("x86: acpi: Generate SPCR table")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix the tags format in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently, the calculation for the length of the DSDT table includes any
bytes that are added for alignment, but those bytes are not initialized.
This is because the DSDT length is calculated after a call to
acpi_inc_align(). Split this up into the following sequence:
* acpi_inc()
* Calculate DSDT length
* acpi_align()
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f05
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Pull request for UEFI sub-system for efi-2020-10-rc5 (2)
The following bugs are fixed:
* incorrect online help for setenv and env
* description of function efi_mem_carve_out()
* replace printf() by log_err() in stm32mp1_rng driver
A unit test is provided to check that the boot hart id is provided in the
RISC-V device-tree.
- SquashFS Coverity fixes
- bitflip fix in the alternate memtest command
- Disable networking on bcmstb boards where we didn't have any network
drivers enabled.
'env -e -i' syntax was changed from "," to ":". Account for this also
in the documentation.
Fixes: 2b3fbcb59f ("efi_loader: use ':' as separator for setenv -i")
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Correct the usage description for setenv -e too.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On RISC-V check that the /chosen node has a boot-hartid property.
To run the test configure with CONFIG_CMD_BOOTEFI_SELFTEST=y and issue
setenv efi_selftest device tree
setenv serial# myserial
bootefi selftest
If the test succeeds, it reports the boot-hartid, e.g.
boot-hartid: 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow specifying the node on which a property is searched.
Test the device tree consistency more rigorously.
Some efi_st_printf() calls have been converted to efi_st_error().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Refine text for overlap_only_ram description to
match to what exactly flag does and aling description
with other functions.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The logging system provides flexible filtering and enhanced output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The bitflip test uses two equal sized memory buffers. This is achieved
by splitting the range of memory into two pieces. The address of the
second buffer, as well as the length of each buffer, were not correctly
calculated. This caused bitflip test to access beyond the end of range.
This patch fixes the pointer arithmetic problem.
A second problem arises because u-boot "mtest" command expects the
ending address to be inclusive. When computing (end - start) this
results in missing 1 byte of the requested length. The bitflip test
expects a count rather than an "ending" address. Thus it fails to test
the last word of the requested range. Fixed by using (end - start + 1).
Added Kconfig option to optionally disable the bitflip test, since it
does add significantly to the time taken for "mtest".
Fixes: 8e434cb705 ("cmd: mem: Add bitflip
memory test to alternate mtest")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Silence the "Driver Model for Ethernet drivers" migration warning for
the bcm7445 and bcm7260 ports, neither of which supports networking yet.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
* 'master' of git://git.denx.de/u-boot: (113 commits)
doc: qemu: debug UART settings for QEMU ARM virt
MAINTAINERS: add myself as reviewer for SquashFS
MAINTAINERS: add myself as reviewer for SquashFS
lib: fdt: Fix fdtdec_setup_mem..() conversion to livetree API
include: phy: fix NULL pointer check in phy_write()
MAINTAINERS: update clk entry git tree
rockchip: make_fit_atf: ignore empty PT_LOAD segment
rockchip: rv1108: enable board early init
rockchip: rv1108: Enable grf as pre-reloc node
rockchip: rv1108: use correct API for board callback
Azure/GitLab/Travis: Add SH4 r2dplus machine with various PCI ethernet options
mmc: xenon_sdhci: Add missing common host capabilities
mmc: msm_sdhci: Use mmc_of_parse for setting host_caps
efi_selftest: restore gd before do_reset()
efi_loader: save global data pointer on RISC-V
riscv: define function set_gd()
efi_loader: efi_var_mem_notify_exit_boot_services
rsa: crash in br_i32_decode() called from rsa_gen_key_prop()
test: do no assume hush parser in validate_empty()
Makefile: mrproper shall delete doc/output/
...
This is not required for sysboot (we defined fdtfile), let's save a few
bytes in the binary image without these variables.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.
Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The size of the binary created with the default U-boot config is much
greater than the default offset for environment `0x60000`.
In case if that binary is used for booting via MMC it is overlapped with
the environment stored on MMC.
This leads to U-Boot corruption while saving environment with `saveenv`
command and non-bootable SabreLite board.
The offset for environment `CONFIG_ENV_OFFSET=0x60000` was added in
commit a09fea1 but did not count in the change to `0xC0000` if option
`CONFIG_ENV_IS_IN_MMC` is used.
The offset is also used for variant with environment saving onto SPI NOR
flash (with enabled option `CONFIG_ENV_IS_IN_SPI_FLASH`). In that case the
U-Boot binary flashed on SPI NOR is also corrupted after environment
saving with the original 0x60000 offset.
Signed-off-by: Denis Pynkin <denis.pynkin@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Latest datasheet revE has removed MIMX8ML7D/5D/7C/5C parts, so
update u-boot to remove decoding and support for those parts.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix SSCG_PLL_REFCLK_SEL_x, the offset starts from 0, not 16
Reported-by: Coverity 3448860
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Coverity reported dead code, however it is FRAC_PLL_REFCLK_SEL_MASK
was wrongly set.
Reported-by: Coverity 10045172
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
According to i.MX 7Dual Applications Processor Reference Manual, Rev. 1
The target interface CCM root index ranges [0,124], so the number
should be 125.
Reported-by: Coverity 18045
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Provide fdtfile value in default env instead of setting
it dynamically in runtime.
Fixes: 85cb2bc686("apalis/colibri imx6: provide proper fdtfile value")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: a62c60610f("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: board: 31b1e17f44("toradex: add Colibri iMX6ULL support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Wrap video specific functionality with ifdefs.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Drop show_boot_logo legacy function, as splashscreen functionality can
be used instead.
Fixes: d324189772("toradex: common: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 391c712dde("colibri-imx6ull: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
I also followed the development of the SquashFS support in U-Boot
as part of Joao Marcos internship, so I would also appreciate receiving
new contributions and bug reports related to this topic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
