dany/u-boot-megous
1
0
Fork 0
mirror of https://xff.cz/git/u-boot/ synced 2025-10-31 10:26:10 +01:00
Code Issues Packages Projects Releases Wiki Activity

tqm5200: Correct comment and code in post_hotkeys_pressed.

Browse Source 
This fixes the code and the comment according to the original intent of
doing an intensive memory test when PSC6_3 is pulled low on the STK52xx.
Notably PORT_CONFIG will be overridden with this correct code now,
so beware.

The original code only worked by coincidence depending on the PORT_CONFIG
setting from the header file.  The new code was tested to ensure that the
(undocumented) memory test still works on the STK52x.

Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Martin Krause <Martin.Krause@tqs.de>

Minor white-space cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This commit is contained in:
Detlev Zundel
2009-10-07 16:38:05 +02:00
committed by Wolfgang Denk
parent da01f53404
commit 95c44ec485
2 changed files with 10 additions and 10 deletions
Download Patch File Download Diff File Expand all files Collapse all files

6
board/tqc/tqm5200/tqm5200.c
View File

@@ -358,11 +358,9 @@ int post_hotkeys_pressed(void)
gpio = (struct mpc5xxx_gpio*) MPC5XXX_GPIO;
/*
* Configure PSC6_1 and PSC6_3 as GPIO. PSC6 then couldn't be used in
* CODEC or UART mode. Consumer IrDA should still be possible.
* Configure PSC6_0 through PSC6_3 as GPIO.
*/
gpio->port_config &= ~(0x07000000);
gpio->port_config |= 0x03000000;
gpio->port_config &= ~(0x00700000);
/* Enable GPIO for GPIO_IRDA_1 (IR_USB_CLK pin) = PSC6_3 */
gpio->simple_gpioe |= 0x20000000;

14
include/configs/TQM5200.h
View File

@@ -540,6 +540,8 @@
* 101 -> use PSC6 as UART. Pins PSC6_0 to PSC6_3 are used.
* Extended POST test is not available.
* Use for STK52xx, FO300 and CAM5200 boards.
* WARNING: When the extended POST is enabled, these bits will
* be overridden by this code as GPIOs!
* use PCI_DIS: Bit 16 (mask 0x00008000):
* 1 -> disable PCI controller (on CAM5200 board).
* use USB: Bits 18-19 (mask 0x00003000):
@@ -552,7 +554,7 @@
* 000 -> All PSC2 pins are GPIOs.
* 100 -> UART (on CAM5200 board).
* 001 -> CAN1/2 on PSC2 pins.
* Use for REV100 STK52xx boards
* Use for REV100 STK52xx boards
* 01x -> Use AC97 (on FO300 board).
* use PSC1: Bits 29-31 (mask: 0x00000007):
* 100 -> UART (on all boards).
@@ -711,20 +713,20 @@
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
/* Offset for data I/O */
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
/* Offset for normal register accesses */
#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
/* Offset for alternate registers */
#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
/* Interval between registers */
#define CONFIG_SYS_ATA_STRIDE 4
/* Support ATAPI devices */
#define CONFIG_ATAPI 1
#define CONFIG_ATAPI 1
/*-----------------------------------------------------------------------
* Open firmware flat tree support