sdcard_image-sunxi: fix dependency loop

As suggested by Andrei Gherzan (see #178):

"The current implementation inherits sdcard_image-sunxi.bbclass
unconditionally which in turn, sets two depends on do_rootfs
unconditionally again.

This means that if I want to build an initramfs image in the
kernel image I will get a dependency loop."

Signed-off-by: Enrico Butera <ebutera@users.sourceforge.net>
(cherry picked from commit a84d6a40c1)

README.md

@@ -3,9 +3,9 @@ meta-sunxi
 
 Official sunxi OpenEmbedded layer for Allwinner-based boards.
 
-This layer depends on the additional layers:
+This layer depends on the additional layer:
 
-* [meta-openembedded/meta-oe](http://git.openembedded.org/meta-openembedded/tree/meta-oe)
+meta-openembedded: git://git.openembedded.org/meta-openembedded
 
 Tested with core-image-base.
 
@@ -14,30 +14,24 @@ Maintainers:
 * Nicolas Aguirre <aguirre.nicolas@gmail.com>
 * Enrico Butera <ebutera@users.sourceforge.net>
 * Sergey Lapin <slapin@ossfans.org>
-* Marek Belisko <marek.belisko@gmail.com>
 
 Kernel / U-Boot Version
 ===========
 Most Allwinner devices and hardware are supported in mainline kernel and U-Boot, so this layer builds mainline by default.
 There is a custom U-Boot and Kernel version for sunxi devices which includes some special drivers not mainlined.
-These versions are rather old (3.4 for kernel and 2014.04 for U-Boot), but may support more functions and devices than current mainline
+These versions are rather old (3.4 for kernel and 2014.04 for U-Boot), but may support more functions and devices than current mainline 
 
 If you want to switch back to sunxi versions for some reasons (no device tree available, unsupported hardware), either:
 - change the file conf/machine/include/sunxi.inc to include the following block
 - edit your conf/local.conf to add the following block
 
-		PREFERRED_PROVIDER_u-boot="u-boot-sunxi"
+	PREFERRED_PROVIDER_u-boot="u-boot-sunxi"
-		PREFERRED_PROVIDER_virtual/bootloader="u-boot-sunxi"
+	PREFERRED_PROVIDER_virtual/bootloader="u-boot-sunxi"
-		PREFERRED_PROVIDER_virtual/kernel="linux-sunxi"
+	PREFERRED_PROVIDER_virtual/kernel="linux-sunxi"
-		KERNEL_DEVICETREE = ""
 
 If you already have built the mainline versions it might be necessary to reset the build directories with:
 
-	bitbake -c clean virtual/kernel virtual/bootloader
+	bitbake -c clean linux u-boot
-
-For mainline kernel we have now support for latest LTS, stable and bleeding edge (latest possible rc).
-By default we use latest LTS. If you would like to change version please update ```PREFERRED_VERSION_linux-mainline``` in:
-* [conf/machine/include/sunxi.inc](https://github.com/linux-sunxi/meta-sunxi/blob/4921234ed77f9df77c65c88637ce50468f65bde7/conf/machine/include/sunxi.inc#L16)
 
 Performance
 ===========

classes/sdcard_image-sunxi.bbclass

@@ -7,8 +7,8 @@ inherit image_types
 # The disk layout used is:
 #
 #    0                      -> 8*1024                           - reserverd
-#    8*1024                 ->                                  - arm combined spl/u-boot or aarch64 spl
+#    8*1024                 -> 32*1024                          - 
-#    40*1024                ->                                  - aarch64 u-boot
+#    32*1024                -> 2048*1024                        - 
 #    2048*1024              -> BOOT_SPACE                       - bootloader and kernel
 #
 #
@@ -20,19 +20,19 @@ IMAGE_TYPEDEP_sunxi-sdimg = "${SDIMG_ROOTFS_TYPE}"
 BOOTDD_VOLUME_ID ?= "${MACHINE}"
 
 # Boot partition size [in KiB]
-BOOT_SPACE ?= "40960"
+BOOT_SPACE ?= "20480"
 
 # First partition begin at sector 2048 : 2048*1024 = 2097152
 IMAGE_ROOTFS_ALIGNMENT = "2048"
 
-# Use an uncompressed ext4 by default as rootfs
+# Use an uncompressed ext3 by default as rootfs
 SDIMG_ROOTFS_TYPE ?= "ext4"
 SDIMG_ROOTFS = "${IMGDEPLOYDIR}/${IMAGE_NAME}.rootfs.${SDIMG_ROOTFS_TYPE}"
 
-do_image_sunxi_sdimg[depends] += " \
+IMAGE_DEPENDS_sunxi-sdimg += " \
-			parted-native:do_populate_sysroot \
+			parted-native \
-			mtools-native:do_populate_sysroot \
+			mtools-native \
-			dosfstools-native:do_populate_sysroot \
+			dosfstools-native \
 			virtual/kernel:do_deploy \
 			virtual/bootloader:do_deploy \
 			"
@@ -64,23 +64,17 @@ IMAGE_CMD_sunxi-sdimg () {
 	rm -f ${WORKDIR}/boot.img
 	mkfs.vfat -n "${BOOTDD_VOLUME_ID}" -S 512 -C ${WORKDIR}/boot.img $BOOT_BLOCKS
 
-	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin ::${KERNEL_IMAGETYPE}
+	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin ::uImage
 
 	# Copy device tree file
 	if test -n "${KERNEL_DEVICETREE}"; then
 		for DTS_FILE in ${KERNEL_DEVICETREE}; do
 			DTS_BASE_NAME=`basename ${DTS_FILE} | awk -F "." '{print $1}'`
-			DTS_DIR_NAME=`dirname ${DTS_FILE}`
+			if [ -e ${DEPLOY_DIR_IMAGE}/"${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb" ]; then
-			if [ -e ${DEPLOY_DIR_IMAGE}/"${DTS_BASE_NAME}.dtb" ]; then
-
-				if [ ${DTS_FILE} != ${DTS_BASE_NAME}.dtb ]; then
-					mmd -i ${WORKDIR}/boot.img ::/${DTS_DIR_NAME}
-				fi
-
 				kernel_bin="`readlink ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin`"
-				kernel_bin_for_dtb="`readlink ${DEPLOY_DIR_IMAGE}/${DTS_BASE_NAME}.dtb | sed "s,$DTS_BASE_NAME,${KERNEL_IMAGETYPE},g;s,\.dtb$,.bin,g"`"
+				kernel_bin_for_dtb="`readlink ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb | sed "s,$DTS_BASE_NAME,${MACHINE},g;s,\.dtb$,.bin,g"`"
 				if [ $kernel_bin = $kernel_bin_for_dtb ]; then
-					mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${DTS_BASE_NAME}.dtb ::/${DTS_FILE}
+					mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTS_BASE_NAME}.dtb ::/${DTS_BASE_NAME}.dtb
 				fi
 			fi
 		done
@@ -110,15 +104,7 @@ IMAGE_CMD_sunxi-sdimg () {
 		dd if=${SDIMG_ROOTFS} of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
 	fi
 
-	# write u-boot-spl at the begining of sdcard in one shot
+	#write u-boot and spl at the beginint of sdcard in one shot
-	SPL_FILE=$(basename ${SPL_BINARY})
+	dd if=${DEPLOY_DIR_IMAGE}/u-boot-sunxi-with-spl.bin of=${SDIMG} bs=1024 seek=8 conv=notrunc
-	dd if=${DEPLOY_DIR_IMAGE}/${SPL_FILE} of=${SDIMG} bs=1024 seek=8 conv=notrunc
-}
 
-# write uboot.itb for arm64 boards
-IMAGE_CMD_sunxi-sdimg_append_sun50i () {
-	if [ -e "${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY}" ]
-	then
-		dd if=${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY} of=${SDIMG} bs=1024 seek=40 conv=notrunc
-	fi
 }

conf/layer.conf

@@ -7,11 +7,3 @@ BBFILES += "${LAYERDIR}/recipes*/*/*.bb ${LAYERDIR}/recipes*/*/*.bbappend"
 BBFILE_COLLECTIONS += "meta-sunxi"
 BBFILE_PATTERN_meta-sunxi := "^${LAYERDIR}/"
 BBFILE_PRIORITY_meta-sunxi = "10"
-
-# This should only be incremented on significant changes that will
-# cause compatibility issues with other layers
-LAYERVERSION_meta-sunxi = "1"
-
-LAYERDEPENDS_meta-sunxi = "core openembedded-layer"
-
-LAYERSERIES_COMPAT_meta-sunxi = "zeus"

conf/machine/include/sun50i.inc

@@ -1,6 +0,0 @@
-require conf/machine/include/sunxi64.inc
-
-DEFAULTTUNE ?= "cortexa53-crypto"
-require conf/machine/include/tune-cortexa53.inc
-
-SOC_FAMILY = "sun50i"

conf/machine/include/sunxi-mali.inc

@@ -4,8 +4,6 @@ PREFERRED_PROVIDER_virtual/libgles1 ?= "sunxi-mali"
 PREFERRED_PROVIDER_virtual/libgles2 ?= "sunxi-mali"
 PREFERRED_PROVIDER_virtual/egl ?= "sunxi-mali"
 
-PACKAGECONFIG_remove_pn-xserver-xorg = "${@bb.utils.contains('DISTRO_FEATURES', 'x11', 'glamor', '', d)}"
-
 XSERVER += "sunxi-mali \
             sunxi-mali-dev"
 

conf/machine/include/sunxi.inc

@@ -12,8 +12,7 @@ XSERVER = "xserver-xorg \
            xf86-input-mouse \
            xf86-input-keyboard"
 
-PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
+PREFERRED_PROVIDER_virtual/kernel ?= "linux"
-PREFERRED_VERSION_linux-mainline ?= "4.19%"
 PREFERRED_PROVIDER_u-boot ?= "u-boot"
 PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"
 
@@ -27,8 +26,7 @@ MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"
 UBOOT_LOCALVERSION = "-g${@d.getVar('SRCPV', True).partition('+')[2][0:7]}"
 
 UBOOT_ENTRYPOINT ?= "0x40008000"
-
+UBOOT_LOADADDRESS ?= "0x400080OB00"
-SPL_BINARY ?= "u-boot-sunxi-with-spl.bin"
 
 SERIAL_CONSOLE ?= "115200 ttyS0"
 MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"

conf/machine/include/sunxi64.inc

@@ -1,24 +0,0 @@
-SOC_FAMILY ??= ""
-include conf/machine/include/soc-family.inc
-
-PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
-PREFERRED_PROVIDER_u-boot ?= "u-boot"
-PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"
-
-KERNEL_IMAGETYPE ?= "Image"
-
-IMAGE_CLASSES += "sdcard_image-sunxi"
-IMAGE_FSTYPES += "ext4 tar.gz sunxi-sdimg"
-
-MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"
-
-UBOOT_LOCALVERSION = "-g${@d.getVar('SRCPV', True).partition('+')[2][0:7]}"
-
-UBOOT_ENTRYPOINT ?= "0x40008000"
-UBOOT_LOADADDRESS ?= "0x400080OB00"
-
-UBOOT_BINARY ?= "u-boot.itb"
-SPL_BINARY ?= "spl/sunxi-spl.bin"
-
-SERIAL_CONSOLE ?= "115200 ttyS0"
-MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"

conf/machine/nanopi-m1-plus.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: nanopi M1 Plus
-#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo, based on the Allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "sun8i-h3-nanopi-m1-plus.dtb"
-UBOOT_MACHINE = "nanopi_m1_plus_defconfig"
-

conf/machine/nanopi-neo-air.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: nanopi-neo-air
-#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo Air, based
-# on the Allwinner H3 CPU.
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo-air.dtb"
-UBOOT_MACHINE = "nanopi_neo_air_defconfig"

conf/machine/nanopi-neo-plus2.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: nanopi-neo-plus2
-#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo Plus2, based
-# on the Allwinner H5 SoC.
-
-require conf/machine/include/sun50i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h5-nanopi-neo-plus2.dtb"
-UBOOT_MACHINE = "nanopi_neo_plus2_defconfig"

conf/machine/nanopi-neo.conf

@@ -4,6 +4,10 @@
 
 require conf/machine/include/sun8i.inc
 
+PREFERRED_VERSION_linux = "4.9.0+git%"
+PREFERRED_VERSION_u-boot = "v2016.11%"
+
 KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo.dtb"
 UBOOT_MACHINE = "nanopi_neo_defconfig"
 
+DEFAULTTUNE = "cortexa7hf-neon-vfpv4"

conf/machine/nanopi-neo2.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: nanopi-neo2
-#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo 2, based on
-# the Allwinner H5 SoC.
-
-require conf/machine/include/sun50i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h5-nanopi-neo2.dtb"
-UBOOT_MACHINE = "nanopi_neo2_defconfig"

conf/machine/olinuxino-a20lime2-emmc.conf

@@ -1,10 +0,0 @@
-#@TYPE: Machine
-#@NAME: Olimex A20-OLinuXino Lime2 Board with 4GB eMMC
-#@DESCRIPTION: Machine configuration for the Olimex A20-OLinuXino Lime2 Board with 4GB eMMC, based on Allwinner A20 CPU
-#https://github.com/OLIMEX/OLINUXINO
-
-require conf/machine/include/sun7i.inc
-
-KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime2-emmc.dtb"
-UBOOT_MACHINE = "A20-OLinuXino-Lime2-eMMC_config"
-SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime2.fex"

conf/machine/olinuxino-a64.conf

@@ -1,13 +0,0 @@
-#@TYPE: Machine
-#@NAME: Olimex A64-OLinuXino Board
-#@DESCRIPTION: Machine configuration for the Olimex A64-OLinuXino Board, based on Allwinner A64 CPU
-#https://github.com/OLIMEX/OLINUXINO
-
-require conf/machine/include/sun50i.inc
-
-PREFFERED_VERSION_u-boot = "v2018.09%"
-
-MACHINE_EXTRA_RRECOMMENDS += " linux-firmware-rtl8723"
-
-KERNEL_DEVICETREE = "allwinner/sun50i-a64-olinuxino.dtb"
-UBOOT_MACHINE = "a64-olinuxino_defconfig"

conf/machine/orange-pi-one.conf

@@ -4,6 +4,10 @@
 
 require conf/machine/include/sun8i.inc
 
+PREFERRED_VERSION_linux = "4.9.0+git%"
+PREFERRED_VERSION_u-boot = "v2016.11%"
+
 KERNEL_DEVICETREE = "sun8i-h3-orangepi-one.dtb"
 UBOOT_MACHINE = "orangepi_one_defconfig"
 
+DEFAULTTUNE = "cortexa7hf-neon-vfpv4"

conf/machine/orange-pi-pc-plus.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-pc-plus
-#@DESCRIPTION: Machine configuration for the orange-pi-pc-plus, base on allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc-plus.dtb"
-UBOOT_MACHINE = "orangepi_pc_plus_defconfig"
-

conf/machine/orange-pi-pc.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-one
-#@DESCRIPTION: Machine configuration for the orange-pi-one, base on allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc.dtb"
-UBOOT_MACHINE = "orangepi_pc_defconfig"
-

conf/machine/orange-pi-zero-plus2.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-zero-plus2
-#@DESCRIPTION: Machine configuration for the orange-pi-zero-plus2, base on Allwinner H5 CPU
-
-
-require conf/machine/include/sun50i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h5-orangepi-zero-plus2.dtb"
-UBOOT_MACHINE = "orangepi_zero_plus2_defconfig"

conf/machine/orange-pi-zero.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-one
-#@DESCRIPTION: Machine configuration for the orange-pi-one, base on allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "sun8i-h2-plus-orangepi-zero.dtb"
-UBOOT_MACHINE = "orangepi_zero_defconfig"
-

conf/machine/pcduino.conf

@@ -4,6 +4,9 @@
 
 require conf/machine/include/sun4i.inc
 
+PREFERRED_VERSION_linux = "4.9.0+git%"
+PREFERRED_VERSION_u-boot = "v2016.11%"
+
 KERNEL_DEVICETREE = "sun4i-a10-pcduino.dtb"
 UBOOT_MACHINE = "Linksprite_pcDuino_defconfig"
 SUNXI_FEX_FILE = "sys_config/a10/pcduino.fex"

conf/machine/pcduino3.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: Linksprite A20-pcduino3 Board
-#@DESCRIPTION: Machine configuration for the pcDuino 3, based on Allwinner A20 CPU
-
-require conf/machine/include/sun7i.inc
-
-KERNEL_DEVICETREE = "sun7i-a20-pcduino3.dtb"
-UBOOT_MACHINE = "Linksprite_pcDuino3_defconfig"
-SUNXI_FEX_FILE = "sys_config/a20/linksprite_pcduino3.fex"

conf/machine/pine64-plus.conf

@@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: pine64-plus
-#@DESCRIPTION: Machine configuration for the pine64-plus, based on Allwinner A64 CPU
-
-
-require conf/machine/include/sun50i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-a64-pine64-plus.dtb"
-UBOOT_MACHINE = "pine64_plus_defconfig"

recipes-bsp/atf/atf-sunxi_git.bb

@@ -1,27 +0,0 @@
-DESCRIPTION = "ARM Trusted Firmware Allwinner"
-LICENSE = "BSD"
-LIC_FILES_CHKSUM = "file://license.md;md5=829bdeb34c1d9044f393d5a16c068371"
-
-SRC_URI = "git://github.com/apritzel/arm-trusted-firmware;nobranch=1"
-SRCREV = "aa75c8da415158a94b82a430b2b40000778e851f"
-
-S = "${WORKDIR}/git"
-B = "${WORKDIR}/build"
-
-COMPATIBLE_MACHINE = "(sun50i)"
-
-PLATFORM_sun50i = "sun50iw1p1"
-
-LDFLAGS[unexport] = "1"
-
-do_compile() {
-    oe_runmake -C ${S} BUILD_BASE=${B} \
-      CROSS_COMPILE=${TARGET_PREFIX} \
-      PLAT=${PLATFORM} \
-      bl31 \
-      all
-}
-
-do_install() {
-    install -D -p -m 0644 ${B}/${PLATFORM}/release/bl31.bin ${DEPLOY_DIR_IMAGE}/bl31.bin
-}

recipes-bsp/u-boot/files/0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch

@@ -1,21 +0,0 @@
-From 6adb2ebdc4022c24497e9ee4dccab41d18e3105d Mon Sep 17 00:00:00 2001
-From: Florin Sarbu <florin@resin.io>
-Date: Wed, 12 Sep 2018 14:22:49 +0200
-Subject: [PATCH] nanopi_neo_air_defconfig: Enable eMMC support
-
-Upstream-status: Pending
-Signed-off-by: Florin Sarbu <florin@resin.io>
-
----
- configs/nanopi_neo_air_defconfig | 1 +
- 1 file changed, 1 insertion(+)
-
-diff --git a/configs/nanopi_neo_air_defconfig b/configs/nanopi_neo_air_defconfig
-index 5ad90ddd16..8b7a4eb45d 100644
---- a/configs/nanopi_neo_air_defconfig
-+++ b/configs/nanopi_neo_air_defconfig
-@@ -15,3 +15,4 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-neo-air"
- CONFIG_USB_EHCI_HCD=y
- CONFIG_USB_OHCI_HCD=y
- CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
-+CONFIG_MMC_SUNXI_SLOT_EXTRA=2

recipes-bsp/u-boot/files/aarch64/boot.cmd

@@ -1,11 +0,0 @@
-# Default to (primary) SD
-rootdev=mmcblk0p2
-if itest.b *0x28 == 0x02 ; then
-	# U-Boot loaded from eMMC or secondary SD so use it for rootfs too
-	echo "U-boot loaded from eMMC or secondary SD"
-	rootdev=mmcblk1p2
-fi
-setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
-load mmc 0:1 ${fdt_addr_r} ${fdtfile}
-load mmc 0:1 ${kernel_addr_r} Image
-booti ${kernel_addr_r} - ${fdt_addr_r}

recipes-bsp/u-boot/files/boot.cmd

@@ -1,11 +1,4 @@
-# Default to (primary) SD
+setenv bootargs console=${console} console=tty1 root=/dev/mmcblk0p2 rootwait panic=10 ${extra}
-rootdev=mmcblk0p2
-if itest.b *0x28 == 0x02 ; then
-	# U-Boot loaded from eMMC or secondary SD so use it for rootfs too
-	echo "U-boot loaded from eMMC or secondary SD"
-	rootdev=mmcblk1p2
-fi
-setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
 load mmc 0:1 ${fdt_addr_r} ${fdtfile} || load mmc 0:1 ${fdt_addr_r} boot/${fdtfile}
 load mmc 0:1 ${kernel_addr_r} zImage || load mmc 0:1 ${kernel_addr_r} boot/zImage || load mmc 0:1 ${kernel_addr_r} uImage || load mmc 0:1 ${kernel_addr_r} boot/uImage
 bootz ${kernel_addr_r} - ${fdt_addr_r} || bootm ${kernel_addr_r} - ${fdt_addr_r}

recipes-bsp/u-boot/u-boot-sunxi.bb

@@ -20,9 +20,8 @@ UBOOT_MACHINE_meleg = "Mele_A1000G_config"
 
 SRC_URI = " \
 	git://github.com/linux-sunxi/u-boot-sunxi.git;protocol=git;branch=sunxi \
-	file://0001-gcc5-fixes.patch \
+	file://0002-gcc5-fixes.patch \
-	file://0002-gcc6-fixes.patch \
+	file://0003-gcc6-fixes.patch \
-	file://0003-No-gcc-version-specific-includes.patch \
 	"
 
 PE = "1"
@@ -36,7 +35,3 @@ S = "${WORKDIR}/git"
 PACKAGE_ARCH = "${MACHINE_ARCH}"
 
 SPL_BINARY="u-boot-sunxi-with-spl.bin"
-
-do_configure () {
-    oe_runmake -C ${S} O=${B} ${UBOOT_MACHINE}
-}

recipes-bsp/u-boot/u-boot-sunxi/0003-No-gcc-version-specific-includes.patch

@@ -1,24 +0,0 @@
-From bc4aa5814cbedbfaa1c79dfe7ea2571fee7f2d51 Mon Sep 17 00:00:00 2001
-From: Andrey Lebedev <andrey@lebedev.lt>
-Date: Wed, 22 Jan 2020 20:00:11 +0200
-Subject: [PATCH] No gcc version-specific includes
-
-In order to support gcc-5 and above. Fixes compilation errors like
-
-linux/compiler-gcc9.h: No such file or directory
----
- include/linux/compiler-gcc.h | 1 -
- 1 file changed, 1 deletion(-)
-
-diff --git a/include/linux/compiler-gcc.h b/include/linux/compiler-gcc.h
-index 9896e547b9..5f0bd65f3a 100644
---- a/include/linux/compiler-gcc.h
-+++ b/include/linux/compiler-gcc.h
-@@ -90,4 +90,3 @@
- #define __gcc_header(x) #x
- #define _gcc_header(x) __gcc_header(linux/compiler-gcc##x.h)
- #define gcc_header(x) _gcc_header(x)
--#include gcc_header(__GNUC__)
--- 
-2.20.1
-

recipes-bsp/u-boot/u-boot_%.bbappend

@@ -1,29 +0,0 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/files:"
-
-DEPENDS += " bc-native dtc-native swig-native python3-native flex-native bison-native "
-DEPENDS_append_sun50i = " atf-sunxi "
-
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
-
-DEFAULT_PREFERENCE_sun4i="1"
-DEFAULT_PREFERENCE_sun5i="1"
-DEFAULT_PREFERENCE_sun7i="1"
-DEFAULT_PREFERENCE_sun8i="1"
-DEFAULT_PREFERENCE_sun50i="1"
-
-SRC_URI += " \
-           file://0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch \
-           file://boot.cmd \
-           "
-
-UBOOT_ENV_SUFFIX = "scr"
-UBOOT_ENV = "boot"
-
-EXTRA_OEMAKE += ' HOSTLDSHARED="${BUILD_CC} -shared ${BUILD_LDFLAGS} ${BUILD_CFLAGS}" '
-EXTRA_OEMAKE_append_sun50i = " BL31=${DEPLOY_DIR_IMAGE}/bl31.bin "
-
-do_compile_sun50i[depends] += "atf-sunxi:do_deploy"
-
-do_compile_append() {
-    ${B}/tools/mkimage -C none -A arm -T script -d ${WORKDIR}/boot.cmd ${WORKDIR}/${UBOOT_ENV_BINARY}
-}

recipes-bsp/u-boot/u-boot_2016.11.bb

@@ -0,0 +1,47 @@
+DESCRIPTION="Upstream's U-boot configured for sunxi devices"
+
+require recipes-bsp/u-boot/u-boot.inc
+
+DEPENDS += "dtc-native"
+
+LICENSE = "GPLv2"
+
+LIC_FILES_CHKSUM = "\
+file://Licenses/Exceptions;md5=338a7cb1e52d0d1951f83e15319a3fe7 \
+file://Licenses/bsd-2-clause.txt;md5=6a31f076f5773aabd8ff86191ad6fdd5 \
+file://Licenses/bsd-3-clause.txt;md5=4a1190eac56a9db675d58ebe86eaf50c \
+file://Licenses/eCos-2.0.txt;md5=b338cb12196b5175acd3aa63b0a0805c \
+file://Licenses/gpl-2.0.txt;md5=b234ee4d69f5fce4486a80fdaf4a4263 \
+file://Licenses/ibm-pibs.txt;md5=c49502a55e35e0a8a1dc271d944d6dba \
+file://Licenses/isc.txt;md5=ec65f921308235311f34b79d844587eb \
+file://Licenses/lgpl-2.0.txt;md5=5f30f0716dfdd0d91eb439ebec522ec2 \
+file://Licenses/lgpl-2.1.txt;md5=4fbd65380cdd255951079008b364516c \
+file://Licenses/x11.txt;md5=b46f176c847b8742db02126fb8af92e2 \
+"
+
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i)"
+
+DEFAULT_PREFERENCE_sun4i="1"
+DEFAULT_PREFERENCE_sun5i="1"
+DEFAULT_PREFERENCE_sun7i="1"
+DEFAULT_PREFERENCE_sun8i="1"
+
+SRC_URI = "git://git.denx.de/u-boot.git;branch=master \
+           file://boot.cmd"
+
+SRCREV = "29e0cfb4f77f7aa369136302cee14a91e22dca71"
+
+PV = "v2016.11+git${SRCPV}"
+
+PE = "2"
+
+S = "${WORKDIR}/git"
+
+SPL_BINARY="u-boot-sunxi-with-spl.bin"
+
+UBOOT_ENV_SUFFIX = "scr"
+UBOOT_ENV = "boot"
+
+do_compile_append() {
+    ${B}/tools/mkimage -C none -A arm -T script -d ${WORKDIR}/boot.cmd ${WORKDIR}/${UBOOT_ENV_BINARY}
+}

recipes-devtools/python/pya20_0.2.1.bb

@@ -8,7 +8,7 @@ DEPENDS = "python"
 # No GPIO mappings for other machines yet
 COMPATIBLE_MACHINE = "(olinuxino-a13|olinuxino-a10|olinuxino-a20|olinuxino-a10lime|olinuxino-a20lime|olinuxino-a20lime2|olinuxino-a13som|olinuxino-a20som)"
 
-SRC_URI = "https://pypi.python.org/packages/source/p/pyA20/pyA20-${PV}.tar.gz \
+SRC_URI = "http://pypi.python.org/packages/source/p/pyA20/pyA20-${PV}.tar.gz \
            file://setup.py.patch \
            file://mapping.h \
           "

recipes-devtools/python/pya20som_0.2.1.bb

@@ -8,7 +8,7 @@ DEPENDS = "python"
 # No GPIO mappings for other machines yet
 COMPATIBLE_MACHINE = "olinuxino-a20som"
 
-SRC_URI = "https://pypi.python.org/packages/source/p/pyA20SOM/pyA20SOM-${PV}.tar.gz \
+SRC_URI = "http://pypi.python.org/packages/source/p/pyA20SOM/pyA20SOM-${PV}.tar.gz \
            file://setup.py.patch \
            file://mapping.h \
           "

recipes-graphics/libgles/sunxi-mali_git.bb

@@ -31,7 +31,7 @@ SRC_URI = "gitsm://github.com/linux-sunxi/sunxi-mali.git \
 
 S = "${WORKDIR}/git"
 
-DEPENDS = "libdrm xorgproto libump patchelf-native"
+DEPENDS = "libdrm dri2proto libump"
 
 PACKAGECONFIG ??= "${@bb.utils.contains('DISTRO_FEATURES', 'x11', 'x11', '', d)} ${@bb.utils.contains('DISTRO_FEATURES', 'wayland', 'wayland', '', d)}"
 PACKAGECONFIG[wayland] = "EGL_TYPE=framebuffer,,,"
@@ -70,13 +70,11 @@ do_install() {
 
     make libdir=${D}${libdir}/ includedir=${D}${includedir}/ install
     make libdir=${D}${libdir}/ includedir=${D}${includedir}/ install -C include
-    rm -f ${D}${includedir}/KHR/khrplatform.h
 
     # Fix .so name and create symlinks, binary package provides .so wich can't be included directly in package without triggering the 'dev-so' QA check
     # Packages like xf86-video-fbturbo dlopen() libUMP.so, so we do need to ship the .so files in ${PN}
 
     mv ${D}${libdir}/libMali.so ${D}${libdir}/libMali.so.3
-    patchelf --set-soname libMali.so.3 ${D}${libdir}/libMali.so.3
     ln -sf libMali.so.3 ${D}${libdir}/libMali.so
 
     for flib in libEGL.so.1.4 libGLESv1_CM.so.1.1 libGLESv2.so.2.0 ; do

recipes-graphics/xorg-xserver/libdri2_git.bb

@@ -3,7 +3,7 @@ DESCRIPTION = "Library for the DRI2 extension to the X Window System"
 LICENSE = "MIT-X"
 LIC_FILES_CHKSUM = "file://COPYING;md5=827da9afab1f727f2a66574629e0f39c"
 
-DEPENDS = "libdrm libxext libxfixes xorgproto"
+DEPENDS = "libdrm libxext xextproto libxfixes dri2proto"
 
 PE = "1"
 PV = "1.0.0+git${SRCPV}"

recipes-graphics/xorg-xserver/xf86-video-fbturbo_git.bb

@@ -5,7 +5,7 @@ DESCRIPTION = "X.Org X server -- A10/A13 display driver"
 LICENSE = "MIT-X"
 LIC_FILES_CHKSUM = "file://COPYING;md5=f91dc3ee5ce59eb4b528e67e98a31266"
 
-DEPENDS += "sunxi-mali libump xorgproto"
+DEPENDS += "sunxi-mali libump xf86driproto"
 
 PE = "3"
 PV = "0.5.1+git${SRCPV}"

recipes-kernel/linux/linux-mainline/0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch

@@ -1,80 +0,0 @@
-From 4ca766a768e783ee5198f1935b7f46a5df9b4a35 Mon Sep 17 00:00:00 2001
-From: Jelle van der Waa <jelle@vdwaa.nl>
-Date: Tue, 23 Jan 2018 15:58:44 -0800
-Subject: [PATCH] ARM: dts: nanopi-neo-air: Add WiFi / eMMC
-
-Enable the WiFi (AP6212) chip and eMMC support for the NanoPi NEO Air.
-
-This patch was originally submitted by Jelle van der Waa. Martin Kelly
-modified it to compile on the latest kernel, fixed up some review
-comments from Maxime Ripard, and re-tested the patch.
-
-The patch has been reworked to add back eMMC support which has been left
-out at the last backport.
-
-Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
-Cc: linux-sunxi@googlegroups.com
-Cc: devicetree@vger.kernel.org
-Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
-Signed-off-by: Martin Kelly <mkelly@xevo.com>
-Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-Signed-off-by: Florin Sarbu <florin@resin.io>
----
- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 34 +++++++++++++++++++++++++++
- 1 file changed, 34 insertions(+)
-
-diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
-index 03ff6f8..a9331fe 100644
---- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
-+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
-@@ -72,6 +72,11 @@
- 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
- 		};
- 	};
-+
-+	wifi_pwrseq: wifi_pwrseq {
-+		compatible = "mmc-pwrseq-simple";
-+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-+	};
- };
- 
- &mmc0 {
-@@ -84,6 +89,35 @@
- 	status = "okay";
- };
- 
-+&mmc1 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&mmc1_pins_a>;
-+	vmmc-supply = <&reg_vcc3v3>;
-+	vqmmc-supply = <&reg_vcc3v3>;
-+	mmc-pwrseq = <&wifi_pwrseq>;
-+	bus-width = <4>;
-+	non-removable;
-+	status = "okay";
-+
-+	brcmf: bcrmf@1 {
-+		reg = <1>;
-+		compatible = "brcm,bcm4329-fmac";
-+		interrupt-parent = <&pio>;
-+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
-+		interrupt-names = "host-wake";
-+	};
-+};
-+
-+&mmc2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&mmc2_8bit_pins>;
-+	vmmc-supply = <&reg_vcc3v3>;
-+	vqmmc-supply = <&reg_vcc3v3>;
-+	bus-width = <8>;
-+	non-removable;
-+	status = "okay";
-+};
-+
- &uart0 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&uart0_pins_a>;
--- 
-2.11.0
-

recipes-kernel/linux/linux-mainline/aarch64/defconfig

@@ -1,619 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_AUDIT=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_IRQ_TIME_ACCOUNTING=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_BSD_PROCESS_ACCT_V3=y
-CONFIG_TASKSTATS=y
-CONFIG_TASK_DELAY_ACCT=y
-CONFIG_TASK_XACCT=y
-CONFIG_TASK_IO_ACCOUNTING=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_NUMA_BALANCING=y
-CONFIG_MEMCG=y
-CONFIG_MEMCG_SWAP=y
-CONFIG_BLK_CGROUP=y
-CONFIG_CGROUP_PIDS=y
-CONFIG_CGROUP_HUGETLB=y
-CONFIG_CPUSETS=y
-CONFIG_CGROUP_DEVICE=y
-CONFIG_CGROUP_CPUACCT=y
-CONFIG_CGROUP_PERF=y
-CONFIG_USER_NS=y
-CONFIG_SCHED_AUTOGROUP=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_ALL=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_PROFILING=y
-CONFIG_JUMP_LABEL=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_IOSCHED_DEADLINE is not set
-CONFIG_ARCH_SUNXI=y
-CONFIG_ARCH_ALPINE=y
-CONFIG_ARCH_BCM2835=y
-CONFIG_ARCH_BCM_IPROC=y
-CONFIG_ARCH_BERLIN=y
-CONFIG_ARCH_BRCMSTB=y
-CONFIG_ARCH_EXYNOS=y
-CONFIG_ARCH_LAYERSCAPE=y
-CONFIG_ARCH_LG1K=y
-CONFIG_ARCH_HISI=y
-CONFIG_ARCH_MEDIATEK=y
-CONFIG_ARCH_MESON=y
-CONFIG_ARCH_MVEBU=y
-CONFIG_ARCH_QCOM=y
-CONFIG_ARCH_ROCKCHIP=y
-CONFIG_ARCH_SEATTLE=y
-CONFIG_ARCH_RENESAS=y
-CONFIG_ARCH_R8A7795=y
-CONFIG_ARCH_R8A7796=y
-CONFIG_ARCH_STRATIX10=y
-CONFIG_ARCH_TEGRA=y
-CONFIG_ARCH_SPRD=y
-CONFIG_ARCH_THUNDER=y
-CONFIG_ARCH_THUNDER2=y
-CONFIG_ARCH_UNIPHIER=y
-CONFIG_ARCH_VEXPRESS=y
-CONFIG_ARCH_XGENE=y
-CONFIG_ARCH_ZX=y
-CONFIG_ARCH_ZYNQMP=y
-CONFIG_PCI=y
-CONFIG_HOTPLUG_PCI_PCIE=y
-CONFIG_PCI_IOV=y
-CONFIG_HOTPLUG_PCI=y
-CONFIG_HOTPLUG_PCI_ACPI=y
-CONFIG_PCI_LAYERSCAPE=y
-CONFIG_PCI_HISI=y
-CONFIG_PCIE_QCOM=y
-CONFIG_PCIE_KIRIN=y
-CONFIG_PCIE_ARMADA_8K=y
-CONFIG_PCI_AARDVARK=y
-CONFIG_PCIE_RCAR=y
-CONFIG_PCIE_ROCKCHIP=m
-CONFIG_PCI_HOST_GENERIC=y
-CONFIG_PCI_XGENE=y
-CONFIG_ARM64_VA_BITS_48=y
-CONFIG_SCHED_MC=y
-CONFIG_NUMA=y
-CONFIG_PREEMPT=y
-CONFIG_KSM=y
-CONFIG_TRANSPARENT_HUGEPAGE=y
-CONFIG_CMA=y
-CONFIG_SECCOMP=y
-CONFIG_KEXEC=y
-CONFIG_CRASH_DUMP=y
-CONFIG_XEN=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_COMPAT=y
-CONFIG_HIBERNATION=y
-CONFIG_WQ_POWER_EFFICIENT_DEFAULT=y
-CONFIG_ARM_CPUIDLE=y
-CONFIG_CPU_FREQ=y
-CONFIG_CPUFREQ_DT=y
-CONFIG_ARM_BIG_LITTLE_CPUFREQ=y
-CONFIG_ARM_SCPI_CPUFREQ=y
-CONFIG_ACPI_CPPC_CPUFREQ=m
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IPV6=m
-CONFIG_NETFILTER=y
-CONFIG_NF_CONNTRACK=m
-CONFIG_NF_CONNTRACK_EVENTS=y
-CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
-CONFIG_NETFILTER_XT_TARGET_LOG=m
-CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
-CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
-CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_FILTER=m
-CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_NAT=m
-CONFIG_IP_NF_TARGET_MASQUERADE=m
-CONFIG_IP_NF_MANGLE=m
-CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_IPTABLES=m
-CONFIG_IP6_NF_FILTER=m
-CONFIG_IP6_NF_TARGET_REJECT=m
-CONFIG_IP6_NF_MANGLE=m
-CONFIG_IP6_NF_NAT=m
-CONFIG_IP6_NF_TARGET_MASQUERADE=m
-CONFIG_BRIDGE=m
-CONFIG_BRIDGE_VLAN_FILTERING=y
-CONFIG_VLAN_8021Q=m
-CONFIG_VLAN_8021Q_GVRP=y
-CONFIG_VLAN_8021Q_MVRP=y
-CONFIG_BPF_JIT=y
-CONFIG_BT=m
-CONFIG_BT_HIDP=m
-# CONFIG_BT_HS is not set
-# CONFIG_BT_LE is not set
-CONFIG_BT_LEDS=y
-# CONFIG_BT_DEBUGFS is not set
-CONFIG_BT_HCIUART=m
-CONFIG_BT_HCIUART_LL=y
-CONFIG_WIRELESS=y
-CONFIG_WIRELESS_EXT=y
-CONFIG_WEXT_CORE=y
-CONFIG_WEXT_PROC=y
-CONFIG_WEXT_PRIV=y
-CONFIG_CFG80211=m
-CONFIG_MAC80211=m
-CONFIG_MAC80211_LEDS=y
-CONFIG_RFKILL=m
-CONFIG_NET_9P=y
-CONFIG_NET_9P_VIRTIO=y
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_DMA_CMA=y
-CONFIG_MTD=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_M25P80=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_DENALI_DT=y
-CONFIG_MTD_SPI_NOR=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_NBD=m
-CONFIG_VIRTIO_BLK=y
-CONFIG_BLK_DEV_NVME=m
-CONFIG_SRAM=y
-CONFIG_EEPROM_AT25=m
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_BLK_DEV_SD=y
-CONFIG_SCSI_SAS_ATA=y
-CONFIG_SCSI_HISI_SAS=y
-CONFIG_SCSI_HISI_SAS_PCI=y
-CONFIG_ATA=y
-CONFIG_SATA_AHCI=y
-CONFIG_SATA_AHCI_PLATFORM=y
-CONFIG_AHCI_CEVA=y
-CONFIG_AHCI_MVEBU=y
-CONFIG_AHCI_XGENE=y
-CONFIG_AHCI_QORIQ=y
-CONFIG_SATA_SIL24=y
-CONFIG_SATA_RCAR=y
-CONFIG_PATA_PLATFORM=y
-CONFIG_PATA_OF_PLATFORM=y
-CONFIG_NETDEVICES=y
-CONFIG_MACVLAN=m
-CONFIG_MACVTAP=m
-CONFIG_TUN=y
-CONFIG_VETH=m
-CONFIG_VIRTIO_NET=y
-CONFIG_AMD_XGBE=y
-CONFIG_NET_XGENE=y
-CONFIG_MACB=y
-CONFIG_HNS_DSAF=y
-CONFIG_HNS_ENET=y
-CONFIG_E1000E=y
-CONFIG_IGB=y
-CONFIG_IGBVF=y
-CONFIG_MVNETA=y
-CONFIG_MVPP2=y
-CONFIG_SKY2=y
-CONFIG_QCOM_EMAC=m
-CONFIG_RAVB=y
-CONFIG_SMC91X=y
-CONFIG_SMSC911X=y
-CONFIG_STMMAC_ETH=m
-CONFIG_MDIO_BUS_MUX_MMIOREG=y
-CONFIG_AT803X_PHY=m
-CONFIG_MARVELL_PHY=m
-CONFIG_MESON_GXL_PHY=m
-CONFIG_MICREL_PHY=y
-CONFIG_REALTEK_PHY=m
-CONFIG_ROCKCHIP_PHY=y
-CONFIG_USB_PEGASUS=m
-CONFIG_USB_RTL8150=m
-CONFIG_USB_RTL8152=m
-CONFIG_USB_USBNET=m
-CONFIG_USB_NET_DM9601=m
-CONFIG_USB_NET_SR9800=m
-CONFIG_USB_NET_SMSC75XX=m
-CONFIG_USB_NET_SMSC95XX=m
-CONFIG_USB_NET_PLUSB=m
-CONFIG_USB_NET_MCS7830=m
-CONFIG_BRCMFMAC=m
-CONFIG_WL18XX=m
-CONFIG_WLCORE_SDIO=m
-CONFIG_INPUT_EVDEV=y
-CONFIG_KEYBOARD_ADC=m
-CONFIG_KEYBOARD_CROS_EC=y
-CONFIG_KEYBOARD_GPIO=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_PM8941_PWRKEY=y
-CONFIG_INPUT_HISI_POWERKEY=y
-# CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIO_AMBAKMI=y
-CONFIG_LEGACY_PTY_COUNT=16
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_EXTENDED=y
-CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_8250_BCM2835AUX=y
-CONFIG_SERIAL_8250_DW=y
-CONFIG_SERIAL_8250_MT6577=y
-CONFIG_SERIAL_8250_UNIPHIER=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_SERIAL_MESON=y
-CONFIG_SERIAL_MESON_CONSOLE=y
-CONFIG_SERIAL_SAMSUNG=y
-CONFIG_SERIAL_SAMSUNG_CONSOLE=y
-CONFIG_SERIAL_TEGRA=y
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=11
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-CONFIG_SERIAL_MSM=y
-CONFIG_SERIAL_MSM_CONSOLE=y
-CONFIG_SERIAL_XILINX_PS_UART=y
-CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
-CONFIG_SERIAL_MVEBU_UART=y
-CONFIG_SERIAL_DEV_BUS=y
-CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
-CONFIG_VIRTIO_CONSOLE=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_MUX=y
-CONFIG_I2C_MUX_PCA954x=y
-CONFIG_I2C_BCM2835=m
-CONFIG_I2C_DESIGNWARE_PLATFORM=y
-CONFIG_I2C_IMX=y
-CONFIG_I2C_MESON=y
-CONFIG_I2C_MV64XXX=y
-CONFIG_I2C_PXA=y
-CONFIG_I2C_QUP=y
-CONFIG_I2C_RK3X=y
-CONFIG_I2C_SH_MOBILE=y
-CONFIG_I2C_TEGRA=y
-CONFIG_I2C_UNIPHIER_F=y
-CONFIG_I2C_RCAR=y
-CONFIG_I2C_CROS_EC_TUNNEL=y
-CONFIG_SPI=y
-CONFIG_SPI_MESON_SPICC=m
-CONFIG_SPI_MESON_SPIFC=m
-CONFIG_SPI_BCM2835=m
-CONFIG_SPI_BCM2835AUX=m
-CONFIG_SPI_ORION=y
-CONFIG_SPI_PL022=y
-CONFIG_SPI_QUP=y
-CONFIG_SPI_ROCKCHIP=y
-CONFIG_SPI_S3C64XX=y
-CONFIG_SPI_SPIDEV=m
-CONFIG_SPMI=y
-CONFIG_PINCTRL_IPQ8074=y
-CONFIG_PINCTRL_SINGLE=y
-CONFIG_PINCTRL_MAX77620=y
-CONFIG_PINCTRL_MSM8916=y
-CONFIG_PINCTRL_MSM8994=y
-CONFIG_PINCTRL_MSM8996=y
-CONFIG_PINCTRL_QDF2XXX=y
-CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
-CONFIG_GPIO_DWAPB=y
-CONFIG_GPIO_PL061=y
-CONFIG_GPIO_RCAR=y
-CONFIG_GPIO_XGENE=y
-CONFIG_GPIO_XGENE_SB=y
-CONFIG_GPIO_PCA953X=y
-CONFIG_GPIO_PCA953X_IRQ=y
-CONFIG_GPIO_MAX77620=y
-CONFIG_POWER_RESET_MSM=y
-CONFIG_POWER_RESET_XGENE=y
-CONFIG_POWER_RESET_SYSCON=y
-CONFIG_SYSCON_REBOOT_MODE=y
-CONFIG_BATTERY_BQ27XXX=y
-CONFIG_SENSORS_ARM_SCPI=y
-CONFIG_SENSORS_LM90=m
-CONFIG_SENSORS_INA2XX=m
-CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
-CONFIG_CPU_THERMAL=y
-CONFIG_THERMAL_EMULATION=y
-CONFIG_BRCMSTB_THERMAL=m
-CONFIG_EXYNOS_THERMAL=y
-CONFIG_ROCKCHIP_THERMAL=m
-CONFIG_WATCHDOG=y
-CONFIG_S3C2410_WATCHDOG=y
-CONFIG_MESON_GXBB_WATCHDOG=m
-CONFIG_MESON_WATCHDOG=m
-CONFIG_RENESAS_WDT=y
-CONFIG_UNIPHIER_WATCHDOG=y
-CONFIG_BCM2835_WDT=y
-CONFIG_MFD_AXP20X_RSB=y
-CONFIG_MFD_CROS_EC=y
-CONFIG_MFD_CROS_EC_I2C=y
-CONFIG_MFD_CROS_EC_SPI=y
-CONFIG_MFD_EXYNOS_LPASS=m
-CONFIG_MFD_HI6421_PMIC=y
-CONFIG_MFD_HI655X_PMIC=y
-CONFIG_MFD_MAX77620=y
-CONFIG_MFD_SPMI_PMIC=y
-CONFIG_MFD_RK808=y
-CONFIG_MFD_SEC_CORE=y
-CONFIG_REGULATOR_AXP20X=y
-CONFIG_REGULATOR_FAN53555=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_REGULATOR_GPIO=y
-CONFIG_REGULATOR_HI6421V530=y
-CONFIG_REGULATOR_HI655X=y
-CONFIG_REGULATOR_MAX77620=y
-CONFIG_REGULATOR_PWM=y
-CONFIG_REGULATOR_QCOM_SMD_RPM=y
-CONFIG_REGULATOR_QCOM_SPMI=y
-CONFIG_REGULATOR_RK808=y
-CONFIG_REGULATOR_S2MPS11=y
-CONFIG_MEDIA_SUPPORT=m
-CONFIG_MEDIA_CAMERA_SUPPORT=y
-CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
-CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
-CONFIG_MEDIA_CONTROLLER=y
-CONFIG_MEDIA_RC_SUPPORT=y
-CONFIG_RC_CORE=m
-CONFIG_RC_DEVICES=y
-CONFIG_RC_DECODERS=y
-CONFIG_IR_MESON=m
-CONFIG_VIDEO_V4L2_SUBDEV_API=y
-# CONFIG_DVB_NET is not set
-CONFIG_V4L_MEM2MEM_DRIVERS=y
-CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
-CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
-CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
-CONFIG_VIDEO_RENESAS_FCP=m
-CONFIG_VIDEO_RENESAS_VSP1=m
-CONFIG_DRM=m
-CONFIG_DRM_NOUVEAU=m
-CONFIG_DRM_EXYNOS=m
-CONFIG_DRM_EXYNOS5433_DECON=y
-CONFIG_DRM_EXYNOS7_DECON=y
-CONFIG_DRM_EXYNOS_DSI=y
-# CONFIG_DRM_EXYNOS_DP is not set
-CONFIG_DRM_EXYNOS_HDMI=y
-CONFIG_DRM_EXYNOS_MIC=y
-CONFIG_DRM_ROCKCHIP=m
-CONFIG_ROCKCHIP_ANALOGIX_DP=y
-CONFIG_ROCKCHIP_CDN_DP=y
-CONFIG_ROCKCHIP_DW_HDMI=y
-CONFIG_ROCKCHIP_DW_MIPI_DSI=y
-CONFIG_ROCKCHIP_INNO_HDMI=y
-CONFIG_DRM_RCAR_DU=m
-CONFIG_DRM_RCAR_LVDS=y
-CONFIG_DRM_RCAR_VSP=y
-CONFIG_DRM_TEGRA=m
-CONFIG_DRM_PANEL_SIMPLE=m
-CONFIG_DRM_I2C_ADV7511=m
-CONFIG_DRM_VC4=m
-CONFIG_DRM_HISI_KIRIN=m
-CONFIG_DRM_MESON=m
-CONFIG_FB=y
-CONFIG_FB_ARMCLCD=y
-CONFIG_BACKLIGHT_GENERIC=m
-CONFIG_BACKLIGHT_PWM=m
-CONFIG_BACKLIGHT_LP855X=m
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SOC=y
-CONFIG_SND_BCM2835_SOC_I2S=m
-CONFIG_SND_SOC_SAMSUNG=y
-CONFIG_SND_SOC_RCAR=m
-CONFIG_SND_SOC_AK4613=m
-CONFIG_SND_SIMPLE_CARD=y
-CONFIG_USB=y
-CONFIG_USB_OTG=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_TEGRA=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_MSM=y
-CONFIG_USB_EHCI_EXYNOS=y
-CONFIG_USB_EHCI_HCD_PLATFORM=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_EXYNOS=y
-CONFIG_USB_OHCI_HCD_PLATFORM=y
-CONFIG_USB_RENESAS_USBHS=m
-CONFIG_USB_STORAGE=y
-CONFIG_USB_DWC3=y
-CONFIG_USB_DWC2=y
-CONFIG_USB_CHIPIDEA=y
-CONFIG_USB_CHIPIDEA_UDC=y
-CONFIG_USB_CHIPIDEA_HOST=y
-CONFIG_USB_ISP1760=y
-CONFIG_USB_HSIC_USB3503=y
-CONFIG_NOP_USB_XCEIV=y
-CONFIG_USB_MSM_OTG=y
-CONFIG_USB_QCOM_8X16_PHY=y
-CONFIG_USB_ULPI=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=m
-CONFIG_USB_MUSB_HDRC=y
-# Restrict to host mode, as it is hard-coded that way in the device tree
-# (dr_mode = "host" in the &usb_otg node)
-CONFIG_USB_MUSB_HOST=y
-CONFIG_USB_MUSB_SUNXI=y
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK_MINORS=32
-CONFIG_MMC_ARMMMCI=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_ACPI=y
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MMC_SDHCI_OF_ARASAN=y
-CONFIG_MMC_SDHCI_OF_ESDHC=y
-CONFIG_MMC_SDHCI_CADENCE=y
-CONFIG_MMC_SDHCI_TEGRA=y
-CONFIG_MMC_MESON_GX=y
-CONFIG_MMC_SDHCI_MSM=y
-CONFIG_MMC_SPI=y
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_DW=y
-CONFIG_MMC_DW_EXYNOS=y
-CONFIG_MMC_DW_K3=y
-CONFIG_MMC_DW_ROCKCHIP=y
-CONFIG_MMC_SUNXI=y
-CONFIG_MMC_BCM2835=y
-CONFIG_MMC_SDHCI_XENON=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_PWM=y
-CONFIG_LEDS_SYSCON=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_CPU=y
-CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-CONFIG_EDAC=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_MAX77686=y
-CONFIG_RTC_DRV_RK808=m
-CONFIG_RTC_DRV_S5M=y
-CONFIG_RTC_DRV_DS3232=y
-CONFIG_RTC_DRV_EFI=y
-CONFIG_RTC_DRV_S3C=y
-CONFIG_RTC_DRV_PL031=y
-CONFIG_RTC_DRV_SUN6I=y
-CONFIG_RTC_DRV_TEGRA=y
-CONFIG_RTC_DRV_XGENE=y
-CONFIG_DMADEVICES=y
-CONFIG_DMA_BCM2835=m
-CONFIG_K3_DMA=y
-CONFIG_MV_XOR_V2=y
-CONFIG_PL330_DMA=y
-CONFIG_TEGRA20_APB_DMA=y
-CONFIG_QCOM_BAM_DMA=y
-CONFIG_QCOM_HIDMA_MGMT=y
-CONFIG_QCOM_HIDMA=y
-CONFIG_RCAR_DMAC=y
-CONFIG_VFIO=y
-CONFIG_VFIO_PCI=y
-CONFIG_VIRTIO_PCI=y
-CONFIG_VIRTIO_BALLOON=y
-CONFIG_VIRTIO_MMIO=y
-CONFIG_XEN_GNTDEV=y
-CONFIG_XEN_GRANT_DEV_ALLOC=y
-CONFIG_STAGING=y
-CONFIG_RTL8723BS=m
-CONFIG_COMMON_CLK_RK808=y
-CONFIG_COMMON_CLK_SCPI=y
-CONFIG_COMMON_CLK_CS2000_CP=y
-CONFIG_COMMON_CLK_S2MPS11=y
-CONFIG_CLK_QORIQ=y
-CONFIG_COMMON_CLK_PWM=y
-CONFIG_COMMON_CLK_QCOM=y
-CONFIG_QCOM_CLK_SMD_RPM=y
-CONFIG_IPQ_GCC_8074=y
-CONFIG_MSM_GCC_8916=y
-CONFIG_MSM_GCC_8994=y
-CONFIG_MSM_MMCC_8996=y
-CONFIG_HWSPINLOCK=y
-CONFIG_HWSPINLOCK_QCOM=y
-CONFIG_ARM_MHU=y
-CONFIG_PLATFORM_MHU=y
-CONFIG_BCM2835_MBOX=y
-CONFIG_HI6220_MBOX=y
-CONFIG_ROCKCHIP_IOMMU=y
-CONFIG_ARM_SMMU=y
-CONFIG_ARM_SMMU_V3=y
-CONFIG_RPMSG_QCOM_SMD=y
-CONFIG_RASPBERRYPI_POWER=y
-CONFIG_QCOM_SMEM=y
-CONFIG_QCOM_SMD_RPM=y
-CONFIG_QCOM_SMP2P=y
-CONFIG_QCOM_SMSM=y
-CONFIG_ROCKCHIP_PM_DOMAINS=y
-CONFIG_ARCH_TEGRA_132_SOC=y
-CONFIG_ARCH_TEGRA_210_SOC=y
-CONFIG_ARCH_TEGRA_186_SOC=y
-CONFIG_EXTCON_USB_GPIO=y
-CONFIG_IIO=y
-CONFIG_EXYNOS_ADC=y
-CONFIG_ROCKCHIP_SARADC=m
-CONFIG_PWM=y
-CONFIG_PWM_BCM2835=m
-CONFIG_PWM_CROS_EC=m
-CONFIG_PWM_MESON=m
-CONFIG_PWM_ROCKCHIP=y
-CONFIG_PWM_SAMSUNG=y
-CONFIG_PWM_TEGRA=m
-CONFIG_PHY_RCAR_GEN3_USB2=y
-CONFIG_PHY_HI6220_USB=y
-CONFIG_PHY_SUN4I_USB=y
-CONFIG_PHY_ROCKCHIP_INNO_USB2=y
-CONFIG_PHY_ROCKCHIP_EMMC=y
-CONFIG_PHY_ROCKCHIP_PCIE=m
-CONFIG_PHY_XGENE=y
-CONFIG_PHY_TEGRA_XUSB=y
-CONFIG_QCOM_L2_PMU=y
-CONFIG_QCOM_L3_PMU=y
-CONFIG_TEE=y
-CONFIG_OPTEE=y
-CONFIG_ARM_SCPI_PROTOCOL=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_EFI_CAPSULE_LOADER=y
-CONFIG_ACPI=y
-CONFIG_ACPI_APEI=y
-CONFIG_ACPI_APEI_GHES=y
-CONFIG_ACPI_APEI_PCIEAER=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_EXT4_FS_POSIX_ACL=y
-CONFIG_BTRFS_FS=m
-CONFIG_BTRFS_FS_POSIX_ACL=y
-CONFIG_FANOTIFY=y
-CONFIG_FANOTIFY_ACCESS_PERMISSIONS=y
-CONFIG_QUOTA=y
-CONFIG_AUTOFS4_FS=y
-CONFIG_FUSE_FS=m
-CONFIG_CUSE=m
-CONFIG_OVERLAY_FS=m
-CONFIG_VFAT_FS=y
-CONFIG_HUGETLBFS=y
-CONFIG_CONFIGFS_FS=y
-CONFIG_EFIVAR_FS=y
-CONFIG_SQUASHFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_NFS_V4_2=y
-CONFIG_ROOT_NFS=y
-CONFIG_9P_FS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_VIRTUALIZATION=y
-CONFIG_KVM=y
-CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_FS=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_LOCKUP_DETECTOR=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_FTRACE is not set
-CONFIG_MEMTEST=y
-CONFIG_SECURITY=y
-CONFIG_CRYPTO_ECHAINIV=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-CONFIG_ARM64_CRYPTO=y
-CONFIG_CRYPTO_SHA256_ARM64=m
-CONFIG_CRYPTO_SHA512_ARM64=m
-CONFIG_CRYPTO_SHA1_ARM64_CE=y
-CONFIG_CRYPTO_SHA2_ARM64_CE=y
-CONFIG_CRYPTO_GHASH_ARM64_CE=y
-CONFIG_CRYPTO_CRCT10DIF_ARM64_CE=m
-CONFIG_CRYPTO_CRC32_ARM64_CE=m
-CONFIG_CRYPTO_AES_ARM64=m
-CONFIG_CRYPTO_AES_ARM64_CE=m
-CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
-CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
-CONFIG_CRYPTO_AES_ARM64_NEON_BLK=m
-CONFIG_CRYPTO_CHACHA20_NEON=m
-CONFIG_CRYPTO_AES_ARM64_BS=m

recipes-kernel/linux/linux-mainline/orange-pi-zero/0001-dts-orange-pi-zero-Add-wifi-support.patch

@@ -1,100 +0,0 @@
-From 055155f463693e61f9018a011ad600d872d6736f Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@open-nandra.com>
-Date: Fri, 2 Aug 2019 14:46:10 +0200
-Subject: [PATCH] dts: orange-pi-zero: Add wifi support
-
-Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
----
- arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 47 ++++++++++++++++++-----
- 1 file changed, 37 insertions(+), 10 deletions(-)
-
-diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
-index 84cd9c0..77b2fc6 100644
---- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
-+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
-@@ -80,13 +80,14 @@
- 		};
- 	};
- 
--	reg_vcc_wifi: reg_vcc_wifi {
--		compatible = "regulator-fixed";
--		regulator-min-microvolt = <3300000>;
--		regulator-max-microvolt = <3300000>;
--		regulator-name = "vcc-wifi";
--		enable-active-high;
-+	vdd_wifi: vdd_wifi {
-+		regulator-name = "wifi";
-+		regulator-min-microvolt = <1800000>;
-+		regulator-max-microvolt = <1800000>;
- 		gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
-+		startup-delay-us = <70000>;
-+		enable-active-high;
-+
- 	};
- 
- 	reg_vdd_cpux: vdd-cpux-regulator {
-@@ -106,10 +107,12 @@
- 			  1300000 1>;
- 	};
- 
--	wifi_pwrseq: wifi_pwrseq {
-+	pwrseq_wifi: pwrseq_wifi {
- 		compatible = "mmc-pwrseq-simple";
-+		pinctrl-names = "default";
-+		pinctrl-0 = <&wifi_rst>;
- 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
--		post-power-on-delay-ms = <200>;
-+		post-power-on-delay-ms = <50>;
- 	};
- };
- 
-@@ -140,9 +143,11 @@
- };
- 
- &mmc1 {
--	vmmc-supply = <&reg_vcc_wifi>;
--	mmc-pwrseq = <&wifi_pwrseq>;
-+	vmmc-supply = <&reg_vcc3v3>;
-+	vqmmc-supply = <&vdd_wifi>;
-+	mmc-pwrseq = <&pwrseq_wifi>;
- 	bus-width = <4>;
-+	max-frequency = <16000000>;
- 	non-removable;
- 	status = "okay";
- 
-@@ -152,6 +157,13 @@
- 	 */
- 	xr819: sdio_wifi@1 {
- 		reg = <1>;
-+		compatible = "xradio,xr819";
-+		pinctrl-names = "default";
-+		pinctrl-0 = <&wifi_wake>;
-+		interrupt-parent = <&pio>;
-+		interrupts = <6 10 IRQ_TYPE_EDGE_RISING>;
-+		interrupt-names = "host-wake";
-+		local-mac-address = [dc 44 6d c0 ff ee];
- 	};
- };
- 
-@@ -208,3 +220,18 @@
- 	status = "okay";
- 	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
- };
-+
-+&pio {
-+	wifi_wake: wifi_wake {
-+		pins = "PG10";
-+		function = "gpio_in";
-+    };
-+};
-+
-+&r_pio {
-+	wifi_rst: wifi_rst {
-+		pins = "PL7";
-+		function = "gpio_out";
-+    };
-+};
-+
--- 
-2.7.4
-

recipes-kernel/linux/linux-mainline_4.19.81.bb

@@ -1,32 +0,0 @@
-SECTION = "kernel"
-DESCRIPTION = "Mainline Longterm Linux kernel"
-LICENSE = "GPLv2"
-LIC_FILES_CHKSUM = "file://COPYING;md5=bbea815ee2795b2f4230826c0c6b8814"
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
-
-inherit kernel
-
-require linux.inc
-
-# Since we're not using git, this doesn't make a difference, but we need to fill
-# in something or kernel-yocto.bbclass will fail.
-KBRANCH ?= "master"
-
-# Pull in the devicetree files into the rootfs
-RDEPENDS_${KERNEL_PACKAGE_NAME}-base += "kernel-devicetree"
-
-KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
-
-S = "${WORKDIR}/linux-${PV}"
-
-SRC_URI[md5sum] = "bf96b6783a2d11178a2aaa3cf376f975"
-SRC_URI[sha256sum] = "293ec1ae0f6b3b4be83a217224b51d137f2163cf2d9d294eecf5d0a354e4e29d"
-
-SRC_URI = "https://www.kernel.org/pub/linux/kernel/v4.x/linux-${PV}.tar.xz \
-        file://0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch \
-        file://defconfig \
-        "
-
-SRC_URI_append_orange-pi-zero += "\
-	file://0001-dts-orange-pi-zero-Add-wifi-support.patch \
-	"

recipes-kernel/linux/linux-mainline_5.3.8.bb

@@ -1,34 +0,0 @@
-SECTION = "kernel"
-DESCRIPTION = "Mainline Stable Linux kernel"
-LICENSE = "GPLv2"
-LIC_FILES_CHKSUM = "file://COPYING;md5=bbea815ee2795b2f4230826c0c6b8814"
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
-
-inherit kernel
-
-require linux.inc
-
-# Since we're not using git, this doesn't make a difference, but we need to fill
-# in something or kernel-yocto.bbclass will fail.
-KBRANCH ?= "master"
-
-DEPENDS += "rsync-native"
-
-# Pull in the devicetree files into the rootfs
-RDEPENDS_${KERNEL_PACKAGE_NAME}-base += "kernel-devicetree"
-
-KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
-
-S = "${WORKDIR}/linux-${PV}"
-
-SRC_URI[md5sum] = "6f4ab59d6ac7311f4245fc359706a0b7"
-SRC_URI[sha256sum] = "78f3cfc6c20b10ff21c0bb22d7d257cab03781c44d8c5aae289f749f94f76649"
-
-SRC_URI = "https://www.kernel.org/pub/linux/kernel/v5.x/linux-${PV}.tar.xz \
-        file://0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch \
-        file://defconfig \
-        "
-
-SRC_URI_append_orange-pi-zero += "\
-	file://0001-dts-orange-pi-zero-Add-wifi-support.patch \
-	"

recipes-kernel/linux/linux-mainline_5.4-rc6.bb

@@ -1,36 +0,0 @@
-SECTION = "kernel"
-DESCRIPTION = "Mainline RC Linux kernel"
-LICENSE = "GPLv2"
-LIC_FILES_CHKSUM = "file://COPYING;md5=bbea815ee2795b2f4230826c0c6b8814"
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
-
-inherit kernel
-
-require linux.inc
-
-# Since we're not using git, this doesn't make a difference, but we need to fill
-# in something or kernel-yocto.bbclass will fail.
-KBRANCH ?= "master"
-
-DEPENDS += "rsync-native"
-
-# Pull in the devicetree files into the rootfs
-RDEPENDS_${KERNEL_PACKAGE_NAME}-base += "kernel-devicetree"
-
-KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
-
-S = "${WORKDIR}/linux-${PV}"
-
-SRC_URI[md5sum] = "58b2b15fb3c429948051ce4f12f30c37"
-SRC_URI[sha256sum] = "b07532aa008438e0bce2b8f0253079a4f1654a048a75ae1477c8826f32feea7a"
-
-SRC_URI = "https://git.kernel.org/torvalds/t/linux-${PV}.tar.gz \
-        file://0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch \
-        file://defconfig \
-        "
-SRC_URI_append_orange-pi-zero += "\
-	file://0001-dts-orange-pi-zero-Add-wifi-support.patch \
-	"
-
-FILES_${KERNEL_PACKAGE_NAME}-base_append = " ${nonarch_base_libdir}/modules/${KERNEL_VERSION}/modules.builtin.modinfo"
-

recipes-kernel/linux/linux-sunxi/0004-arm-put-user-asm-fix.patch

@@ -1,29 +0,0 @@
-From 25a7e85eb0d58479f7d8895b1b29a648bd07d60e Mon Sep 17 00:00:00 2001
-From: Andrey Lebedev <andrey@lebedev.lt>
-Date: Mon, 20 Jan 2020 23:19:51 +0200
-Subject: [PATCH 2/2] Fix asm error in put_user under gcc version 8 and above
-
-Fixes these errors during compilation of linux-sunxi-3.4 kernel:
-/tmp/ccCGMQmS.s:648: Error: .err encountered
-
-Taken from https://patchwork.kernel.org/patch/10546809/
----
- arch/arm/include/asm/uaccess.h | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
-diff --git a/arch/arm/include/asm/uaccess.h b/arch/arm/include/asm/uaccess.h
-index b04850fd..abfafbbf 100644
---- a/arch/arm/include/asm/uaccess.h
-+++ b/arch/arm/include/asm/uaccess.h
-@@ -159,7 +159,7 @@ extern int __put_user_8(void *, unsigned long long);
- 	({								\
- 		unsigned long __limit = current_thread_info()->addr_limit - 1; \
- 		const typeof(*(p)) __user *__tmp_p = (p);		\
--		register const typeof(*(p)) __r2 asm("r2") = (x);	\
-+		register typeof(*(p)) __r2 asm("r2") = (x);		\
- 		register const typeof(*(p)) __user *__p asm("r0") = __tmp_p; \
- 		register unsigned long __l asm("r1") = __limit;		\
- 		register int __e asm("r0");				\
--- 
-2.20.1
-

recipes-kernel/linux/linux-sunxi/0005-silence-warning.patch

@@ -1,25 +0,0 @@
-From 302604ee4a2011871cb26deaf69d567cf57d0fe3 Mon Sep 17 00:00:00 2001
-From: Andrey Lebedev <andrey@lebedev.lt>
-Date: Mon, 20 Jan 2020 23:20:07 +0200
-Subject: [PATCH 1/2] Silence annoying warning
-
----
- include/linux/log2.h | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
-diff --git a/include/linux/log2.h b/include/linux/log2.h
-index fd7ff3d9..14458fdd 100644
---- a/include/linux/log2.h
-+++ b/include/linux/log2.h
-@@ -18,7 +18,7 @@
- /*
-  * deal with unrepresentable constant logarithms
-  */
--extern __attribute__((const, noreturn))
-+extern __attribute__((const))
- int ____ilog2_NaN(void);
- 
- /*
--- 
-2.20.1
-

recipes-kernel/linux/linux-sunxi_3.4.bb

@@ -14,12 +14,9 @@ MACHINE_KERNEL_PR_append = "a"
 SRC_URI += "git://github.com/linux-sunxi/linux-sunxi.git;branch=sunxi-3.4;protocol=git \
         file://0001-compiler-gcc-integrate-the-various-compiler-gcc-345-.patch \
         file://0002-use-static-inline-in-ARM-ftrace.patch \
-        file://0003-gcc5-fixes.patch \
+        file://0001-gcc5-fixes.patch \
-        file://0004-arm-put-user-asm-fix.patch \
-        file://0005-silence-warning.patch \
         file://defconfig \
         "
-LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
 
 S = "${WORKDIR}/git"
 

recipes-kernel/linux/linux.inc

@@ -1,10 +1,11 @@
 DESCRIPTION = "Linux Kernel"
 SECTION = "kernel"
 LICENSE = "GPLv2"
+LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
 
 INC_PR = "r0"
 
-inherit kernel kernel-yocto siteinfo
+inherit kernel siteinfo
 
 # Enable OABI compat for people stuck with obsolete userspace
 ARM_KEEP_OABI ?= "0"
@@ -15,14 +16,12 @@ CMDLINE_DEBUG ?= "loglevel=3"
 
 # Kernel bootlogo is distro-specific (default is OE logo).
 # Logo resolution (qvga, vga, ...) is machine-specific.
-LOGO_SIZE ?= '${@oe.utils.conditional("MACHINE_GUI_CLASS", "bigscreen", "vga", "qvga", d)}'
+LOGO_SIZE ?= '${@base_conditional("MACHINE_GUI_CLASS", "bigscreen", "vga", "qvga", d)}'
 # To use this, add file://${LOGO_SIZE}/logo_linux_clut224.ppm.bz2 or similar
 # to your kernel recipe, and then structure your logos for each resolution
 # accordingly.
 
 LOCALVERSION ?= ""
-KCONFIG_MODE ?= "alldefconfig"
-KMACHINE ?= "${MACHINE}"
 
 #kernel_conf_variable CMDLINE "\"${CMDLINE} ${CMDLINE_DEBUG}\""
 kernel_conf_variable() {
@@ -35,11 +34,8 @@ kernel_conf_variable() {
     fi
 }
 
-do_kernel_configme[depends] += "virtual/${TARGET_PREFIX}binutils:do_populate_sysroot"
-do_kernel_configme[depends] += "virtual/${TARGET_PREFIX}gcc:do_populate_sysroot"
-do_kernel_configme[depends] += "bc-native:do_populate_sysroot bison-native:do_populate_sysroot"
-
 do_configure_prepend() {
+    echo "" > ${B}/.config
     CONF_SED_SCRIPT=""
 
     #
@@ -115,6 +111,9 @@ do_configure_prepend() {
         kernel_conf_variable CMDLINE \"${CMDLINE_NFSROOT_USB} ${CMDLINE_DEBUG}\"
     fi
 
+    sed -e "${CONF_SED_SCRIPT}" \
+    < '${WORKDIR}/defconfig' >>'${B}/.config'
+
     yes '' | oe_runmake -C ${S} O=${B} oldconfig
 }
 

recipes-kernel/linux/linux/defconfig

@@ -511,7 +511,6 @@ CONFIG_GPIO_SYSFS=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_POWER_RESET=y
 CONFIG_THERMAL=y
-CONFIG_THERMAL_OF=y
 CONFIG_CPU_THERMAL=y
 CONFIG_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=y
@@ -688,27 +687,6 @@ CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_PLATFORM=y
-CONFIG_USB_SERIAL=m
-CONFIG_USB_SERIAL_GENERIC=y
-CONFIG_USB_SERIAL_SIMPLE=m
-CONFIG_USB_SERIAL_CP210X=m
-CONFIG_USB_SERIAL_FTDI_SIO=m
-CONFIG_USB_SERIAL_KEYSPAN=m
-CONFIG_USB_SERIAL_KEYSPAN_MPR=y
-CONFIG_USB_SERIAL_KEYSPAN_USA28=y
-CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
-CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
-CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
-CONFIG_USB_SERIAL_KEYSPAN_USA19=y
-CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
-CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
-CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
-CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
-CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
-CONFIG_USB_SERIAL_KLSI=m
-CONFIG_USB_SERIAL_MOS7720=m
-CONFIG_USB_SERIAL_MOS7840=m
-CONFIG_USB_SERIAL_PL2303=m
 CONFIG_MMC=y
 CONFIG_MMC_SUNXI=y
 CONFIG_LEDS_CLASS=y
@@ -751,23 +729,9 @@ CONFIG_PWM_SUN4I=y
 CONFIG_PHY_SUN4I_USB=y
 CONFIG_PHY_SUN9I_USB=y
 CONFIG_EXT4_FS=y
-CONFIG_XFS_FS=m
-CONFIG_XFS_POSIX_ACL=y
-CONFIG_BTRFS_FS=m
-CONFIG_BTRFS_FS_POSIX_ACL=y
 CONFIG_FANOTIFY=y
 CONFIG_AUTOFS4_FS=m
 CONFIG_FUSE_FS=m
-CONFIG_OVERLAY_FS=m
-CONFIG_FSCACHE=m
-CONFIG_FSCACHE_STATS=y
-CONFIG_FSCACHE_HISTOGRAM=y
-CONFIG_CACHEFILES=m
-CONFIG_CACHEFILES_HISTOGRAM=y
-CONFIG_ISO9660_FS=m
-CONFIG_JOLIET=y
-CONFIG_ZISOFS=y
-CONFIG_UDF_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_NFS_FS=y
@@ -783,4 +747,3 @@ CONFIG_CRYPTO_SHA1_ARM_NEON=y
 CONFIG_CRYPTO_SHA256_ARM=y
 CONFIG_CRYPTO_SHA512_ARM_NEON=y
 CONFIG_CRYPTO_AES_ARM_BS=y
-CONFIG_USB_STORAGE=y

recipes-kernel/linux/linux_4.4.40.bb

@@ -0,0 +1,24 @@
+SECTION = "kernel"
+DESCRIPTION = "Mainline Linux kernel"
+LICENSE = "GPLv2"
+LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i)"
+
+inherit kernel
+
+require recipes-kernel/linux/linux-dtb.inc
+require linux.inc
+
+# Pull in the devicetree files into the rootfs
+RDEPENDS_kernel-base += "kernel-devicetree"
+
+KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
+
+S = "${WORKDIR}/linux-${PV}"
+	
+SRC_URI[md5sum] = "2944984c89c272115649c4a08b43f8d0"
+SRC_URI[sha256sum] = "c4bc5ed6e73ed7393cc1b3714b822664224ab866db114eed663de1315718a4e1"
+
+SRC_URI = "https://www.kernel.org/pub/linux/kernel/v4.x/linux-${PV}.tar.xz \
+        file://defconfig \
+        "

recipes-kernel/linux/linux_git.bb

@@ -0,0 +1,28 @@
+SECTION = "kernel"
+DESCRIPTION = "Mainline Linux kernel"
+LICENSE = "GPLv2"
+LIC_FILES_CHKSUM = "file://COPYING;md5=d7810fab7487fb0aad327b76f1be7cd7"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i)"
+
+inherit kernel
+
+require recipes-kernel/linux/linux-dtb.inc
+require linux.inc
+
+# Pull in the devicetree files into the rootfs
+RDEPENDS_kernel-base += "kernel-devicetree"
+
+# Default is to use stable kernel version
+# If you want to use latest git version set to "1"
+DEFAULT_PREFERENCE = "-1" 
+
+KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"
+	
+# 4.9.0
+PV = "4.9.0+git${SRCPV}"
+SRCREV_pn-${PN} = "69973b830859bc6529a7a0468ba0d80ee5117826"
+
+SRC_URI = "git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git;protocol=git;branch=master \
+        file://defconfig \
+        "
+S = "${WORKDIR}/git"

recipes-kernel/xradio-firmware/xradio-firmware.bb

@@ -1,25 +0,0 @@
-DESCRIPTION = "Xradio xr819 WiFi firmware"
-LICENSE = "CC0-1.0"
-LIC_FILES_CHKSUM = "file://${COMMON_LICENSE_DIR}/${LICENSE};md5=0ceb3372c9595f0a8067e55da801e4a1"
-
-PV = "1.0"
-PR = "r0"
-
-SRCREV = "bddd21b7f895be9f0c37e435f0a7ac84405c6091"
-
-COMPATIBLE_MACHINE = "orange-pi-zero"
-
-SRC_URI = "git://github.com/armbian/firmware.git;protocol=https"
-
-S = "${WORKDIR}/git"
-
-do_install() {
-    install -d ${D}${base_libdir}/firmware/xr819
-    install -m 0644 ${S}/xr819/boot_xr819.bin ${D}${base_libdir}/firmware/xr819/
-    install -m 0644 ${S}/xr819/sdd_xr819.bin ${D}${base_libdir}/firmware/xr819/
-    install -m 0644 ${S}/xr819/fw_xr819.bin ${D}${base_libdir}/firmware/xr819/
-}
-
-FILES_${PN} = "${base_libdir}/*"
-
-PACKAGES = "${PN}"

recipes-kernel/xradio/xradio.bb

@@ -1,23 +0,0 @@
-SUMMARY = "Xradio WiFi driver for orangepi-zero"
-LICENSE = "GPLv2"
-LIC_FILES_CHKSUM = "file://LICENSE;md5=a23a74b3f4caf9616230789d94217acb"
-
-inherit module
-
-PV = "0.1"
-PR = "r0"
-
-RDEPENDS_${PN} += "xradio-firmware"
-
-COMPATIBLE_MACHINE = "orange-pi-zero"
-
-SRCREV = "d649e5a78efdc56ecd0951e35ca60db175650232"
-
-SRC_URI = "git://github.com/fifteenhex/xradio.git;protocol=https \
-          "
-
-S = "${WORKDIR}/git"
-
-EXTRA_OEMAKE += "-C ${STAGING_KERNEL_DIR} M=${S}"
-
-KERNEL_MODULE_AUTOLOAD += "xradio_wlan"

recipes-support/sunxi-tools/sunxi-tools_git.bb

@@ -10,8 +10,6 @@ DEPENDS += "libusb"
 SRC_URI = "git://github.com/linux-sunxi/sunxi-tools;protocol=git"
 SRCREV = "9a3d62aa0c820b3dd42ba3409b2043f4143683cd"
 
-inherit pkgconfig
-
 S = "${WORKDIR}/git"
 
 BBCLASSEXTEND = "native nativesdk"