linux-mainline: Added fix for bananapi

Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
2025-07-16 22:09:47 +02:00 · 2020-05-26 09:33:34 +02:00
183 changed files with 453 additions and 234706 deletions
--- a/README.md
+++ b/README.md
@ -6,7 +6,6 @@ Official sunxi OpenEmbedded layer for Allwinner-based boards.
 This layer depends on the additional layers:

 * [meta-openembedded/meta-oe](http://git.openembedded.org/meta-openembedded/tree/meta-oe)
-* [meta-arm](https://git.yoctoproject.org/meta-arm)

 Tested with core-image-base.

@ -17,11 +16,6 @@ Maintainers:
 * Sergey Lapin <slapin@ossfans.org>
 * Marek Belisko <marek.belisko@gmail.com>

-Community
-===========
-
-You can reach community + ask your question on gitter: https://matrix.to/#/#meta-sunxi:gitter.im
-
 Kernel / U-Boot Version
 ===========
 Most Allwinner devices and hardware are supported in mainline kernel and U-Boot, so this layer builds mainline by default.
--- a/classes/sdcard_image-sunxi.bbclass
+++ b/classes/sdcard_image-sunxi.bbclass
@ -0,0 +1,128 @@
+inherit image_types
+
+#
+# Create an image that can by written onto a SD card using dd.
+# Originally written for rasberrypi adapt for the needs of allwinner sunxi based boards
+#
+# The disk layout used is:
+#
+#    0                      -> 8*1024                           - reserverd
+#    8*1024                 ->                                  - arm combined spl/u-boot or aarch64 spl
+#    40*1024                ->                                  - aarch64 u-boot
+#    2048*1024              -> BOOT_SPACE                       - bootloader and kernel
+#
+#
+
+# This image depends on the rootfs image
+IMAGE_TYPEDEP_sunxi-sdimg = "${SDIMG_ROOTFS_TYPE}"
+
+# Boot partition volume id
+BOOTDD_VOLUME_ID ?= "${MACHINE}"
+
+# Boot partition size [in KiB]
+BOOT_SPACE ?= "40960"
+
+# First partition begin at sector 2048 : 2048*1024 = 2097152
+IMAGE_ROOTFS_ALIGNMENT = "2048"
+
+# Use an uncompressed ext4 by default as rootfs
+SDIMG_ROOTFS_TYPE ?= "ext4"
+SDIMG_ROOTFS = "${IMGDEPLOYDIR}/${IMAGE_NAME}.rootfs.${SDIMG_ROOTFS_TYPE}"
+
+do_image_sunxi_sdimg[depends] += " \
+			parted-native:do_populate_sysroot \
+			mtools-native:do_populate_sysroot \
+			dosfstools-native:do_populate_sysroot \
+			virtual/kernel:do_deploy \
+			virtual/bootloader:do_deploy \
+			"
+
+# SD card image name
+SDIMG = "${IMGDEPLOYDIR}/${IMAGE_NAME}.rootfs.sunxi-sdimg"
+
+IMAGE_CMD_sunxi-sdimg () {
+
+	# Align partitions
+	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE} + ${IMAGE_ROOTFS_ALIGNMENT} - 1)
+	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE_ALIGNED} - ${BOOT_SPACE_ALIGNED} % ${IMAGE_ROOTFS_ALIGNMENT})
+	SDIMG_SIZE=$(expr ${IMAGE_ROOTFS_ALIGNMENT} + ${BOOT_SPACE_ALIGNED} + $ROOTFS_SIZE + ${IMAGE_ROOTFS_ALIGNMENT})
+
+	# Initialize sdcard image file
+	dd if=/dev/zero of=${SDIMG} bs=1 count=0 seek=$(expr 1024 \* ${SDIMG_SIZE})
+
+	# Create partition table
+	parted -s ${SDIMG} mklabel msdos
+	# Create boot partition and mark it as bootable
+	parted -s ${SDIMG} unit KiB mkpart primary fat32 ${IMAGE_ROOTFS_ALIGNMENT} $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT})
+	parted -s ${SDIMG} set 1 boot on
+	# Create rootfs partition
+	parted -s ${SDIMG} unit KiB mkpart primary ext2 $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT}) $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT} \+ ${ROOTFS_SIZE})
+	parted ${SDIMG} print
+
+	# Create a vfat image with boot files
+	BOOT_BLOCKS=$(LC_ALL=C parted -s ${SDIMG} unit b print | awk '/ 1 / { print substr($4, 1, length($4 -1)) / 512 /2 }')
+	rm -f ${WORKDIR}/boot.img
+	mkfs.vfat -n "${BOOTDD_VOLUME_ID}" -S 512 -C ${WORKDIR}/boot.img $BOOT_BLOCKS
+
+	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin ::${KERNEL_IMAGETYPE}
+
+	# Copy device tree file
+	if test -n "${KERNEL_DEVICETREE}"; then
+		for DTS_FILE in ${KERNEL_DEVICETREE}; do
+			DTS_BASE_NAME=`basename ${DTS_FILE} | awk -F "." '{print $1}'`
+			DTS_DIR_NAME=`dirname ${DTS_FILE}`
+			if [ -e ${DEPLOY_DIR_IMAGE}/"${DTS_BASE_NAME}.dtb" ]; then
+
+				if [ ${DTS_FILE} != ${DTS_BASE_NAME}.dtb ]; then
+					mmd -i ${WORKDIR}/boot.img ::/${DTS_DIR_NAME}
+				fi
+
+				kernel_bin="`readlink ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin`"
+				kernel_bin_for_dtb="`readlink ${DEPLOY_DIR_IMAGE}/${DTS_BASE_NAME}.dtb | sed "s,$DTS_BASE_NAME,${KERNEL_IMAGETYPE},g;s,\.dtb$,.bin,g"`"
+				if [ $kernel_bin = $kernel_bin_for_dtb ]; then
+					mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${DTS_BASE_NAME}.dtb ::/${DTS_FILE}
+				fi
+			fi
+		done
+	fi
+
+	if [ -e "${DEPLOY_DIR_IMAGE}/fex.bin" ]
+	then
+		mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/fex.bin ::script.bin
+	fi
+	if [ -e "${DEPLOY_DIR_IMAGE}/boot.scr" ]
+	then
+		mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/boot.scr ::boot.scr
+	fi
+        if [ -e "${DEPLOY_DIR_IMAGE}/splash.bmp" ]
+        then
+                mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/splash.bmp ::splash.bmp
+        fi
+
+
+	# Add stamp file
+	echo "${IMAGE_NAME}" > ${WORKDIR}/image-version-info
+	mcopy -i ${WORKDIR}/boot.img -v ${WORKDIR}/image-version-info ::
+
+	# Burn Partitions
+	dd if=${WORKDIR}/boot.img of=${SDIMG} conv=notrunc seek=1 bs=$(expr ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
+	# If SDIMG_ROOTFS_TYPE is a .xz file use xzcat
+	if echo "${SDIMG_ROOTFS_TYPE}" | egrep -q "*\.xz"
+	then
+		xzcat ${SDIMG_ROOTFS} | dd of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
+	else
+		dd if=${SDIMG_ROOTFS} of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
+	fi
+
+	# write u-boot-spl at the begining of sdcard in one shot
+	SPL_FILE=$(basename ${SPL_BINARY})
+	dd if=${DEPLOY_DIR_IMAGE}/${SPL_FILE} of=${SDIMG} bs=1024 seek=8 conv=notrunc
+}
+
+# write uboot.itb for arm64 boards
+IMAGE_CMD_sunxi-sdimg_append_sun50i () {
+	if [ -e "${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY}" ]
+	then
+		dd if=${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY} of=${SDIMG} bs=1024 seek=40 conv=notrunc
+	fi
+}
--- a/conf/layer.conf
+++ b/conf/layer.conf
@ -4,14 +4,14 @@ BBPATH .= ":${LAYERDIR}"
 # We have a recipes directory, add to BBFILES
 BBFILES += "${LAYERDIR}/recipes*/*/*.bb ${LAYERDIR}/recipes*/*/*.bbappend"

-BBFILE_COLLECTIONS += "sunxi"
-BBFILE_PATTERN_sunxi := "^${LAYERDIR}/"
-BBFILE_PRIORITY_sunxi = "10"
+BBFILE_COLLECTIONS += "meta-sunxi"
+BBFILE_PATTERN_meta-sunxi := "^${LAYERDIR}/"
+BBFILE_PRIORITY_meta-sunxi = "10"

 # This should only be incremented on significant changes that will
 # cause compatibility issues with other layers
-LAYERVERSION_sunxi = "1"
+LAYERVERSION_meta-sunxi = "1"

-LAYERDEPENDS_sunxi = "core meta-python meta-arm"
+LAYERDEPENDS_meta-sunxi = "core openembedded-layer"

-LAYERSERIES_COMPAT_sunxi = "styhead"
+LAYERSERIES_COMPAT_meta-sunxi = "zeus dunfell"
--- a/conf/machine/bananapi-m2-berry.conf
+++ b/conf/machine/bananapi-m2-berry.conf
@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: bananapi-m2-berry
-#@DESCRIPTION: Machine configuration for the Banana Pi M2 Berry, based on Allwinner V40 CPU
-
-require conf/machine/include/sun8i.inc
-require conf/machine/include/hardware/ap6212a.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-v40-bananapi-m2-berry.dtb"
-UBOOT_MACHINE = "bananapi_m2_berry_defconfig"
--- a/conf/machine/bananapi-m2-zero.conf
+++ b/conf/machine/bananapi-m2-zero.conf
@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: bananapi-m2-zero
-#@DESCRIPTION: Machine configuration for the Banana Pi M2 Zero, base on Allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-require conf/machine/include/hardware/ap6212a.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-h2-plus-bananapi-m2-zero.dtb"
-UBOOT_MACHINE = "bananapi_m2_zero_defconfig"
--- a/conf/machine/bananapi-m2m.conf
+++ b/conf/machine/bananapi-m2m.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: bananapi-m2m
-#@DESCRIPTION: Machine configuration for the Banana Pi M2M, base on Allwinner H8 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-r16-bananapi-m2m.dtb"
-UBOOT_MACHINE = "Bananapi_m2m_defconfig"
--- a/conf/machine/bananapi-m2plus.conf
+++ b/conf/machine/bananapi-m2plus.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: bananapi-m2plus
-#@DESCRIPTION: Machine configuration for the Banana Pi M2+, base on Allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-h3-bananapi-m2-plus.dtb"
-UBOOT_MACHINE = "bananapi_m2_plus_h3_defconfig"
--- a/conf/machine/bananapi-m64.conf
+++ b/conf/machine/bananapi-m64.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: pine64-plus
-#@DESCRIPTION: Machine configuration for the pine64-plus, based on Allwinner A64 CPU
-
-require conf/machine/include/sun50i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-a64-bananapi-m64.dtb"
-UBOOT_MACHINE = "bananapi_m64_defconfig"
--- a/conf/machine/bananapi.conf
+++ b/conf/machine/bananapi.conf
@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-bananapi.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-bananapi.dtb"
 UBOOT_MACHINE = "Bananapi_config"
-SUNXI_FEX_FILE = "sys_config/a20/Bananapi.fex"
+SUNXI_FEX_FILE = "sys_config/a20/Bananapi.fex"
--- a/conf/machine/cubieboard.conf
+++ b/conf/machine/cubieboard.conf
@ -4,6 +4,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "allwinner/sun4i-a10-cubieboard.dtb"
+KERNEL_DEVICETREE = "sun4i-a10-cubieboard.dtb"
 UBOOT_MACHINE = "Cubieboard_config"
 SUNXI_FEX_FILE = "sys_config/a10/cubieboard.fex"
--- a/conf/machine/cubieboard2.conf
+++ b/conf/machine/cubieboard2.conf
@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-cubieboard2.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-cubieboard2.dtb"
 UBOOT_MACHINE = "Cubieboard2_config"
 SUNXI_FEX_FILE = "sys_config/a20/cubieboard2.fex"
--- a/conf/machine/cubieboard4.conf
+++ b/conf/machine/cubieboard4.conf
@ -1,11 +0,0 @@
-#@TYPE: Machine
-#@NAME: CubieBoard4
-#@DESCRIPTION: Machine configuration for the cubieboard4, based on allwinner A80 CPU http://cubieboard.org/
-
-require conf/machine/include/sun9i.inc
-require conf/machine/include/hardware/ap6330.inc
-
-KERNEL_IMAGETYPE = "zImage"
-
-KERNEL_DEVICETREE = "allwinner/sun9i-a80-cubieboard4.dtb"
-UBOOT_MACHINE = "Cubieboard4_defconfig"
--- a/conf/machine/cubietruck.conf
+++ b/conf/machine/cubietruck.conf
@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-cubietruck.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-cubietruck.dtb"
 UBOOT_MACHINE = "Cubietruck_config"
-SUNXI_FEX_FILE = "sys_config/a20/cubietruck.fex"
+SUNXI_FEX_FILE = "sys_config/a20/cubietruck.fex"
--- a/conf/machine/include/hardware/ap6212a.inc
+++ b/conf/machine/include/hardware/ap6212a.inc
@ -1,9 +1,5 @@
 # Include for boards with AMPAK 6212A Wifi / Bluetooth module
 # https://linux-sunxi.org/Wifi#Ampak

-MACHINE_EXTRA_RRECOMMENDS:append = " kernel-module-brcmfmac kernel-module-hci-uart"
-MACHINE_EXTRA_RDEPENDS:append = " linux-firmware-bcm43430 armbian-firmware-ap6212"
-
-MACHINE_FEATURES:append = " bluetooth wifi"
-
-KERNEL_FEATURES:append = " features/ap6212/ap6212.scc"
+MACHINE_EXTRA_RRECOMMENDS_append = " kernel-module-brcmfmac"
+MACHINE_EXTRA_RDEPENDS_append = " linux-firmware-bcm43430"
--- a/conf/machine/include/hardware/ap6330.inc
+++ b/conf/machine/include/hardware/ap6330.inc
@ -1,7 +0,0 @@
-# Include for boards with AMPAK AP6330 Wifi / Bluetooth module
-# https://linux-sunxi.org/Wifi#Ampak
-
-MACHINE_EXTRA_RRECOMMENDS:append = " kernel-module-brcmfmac"
-MACHINE_EXTRA_RDEPENDS:append = " linux-firmware-bcm4330"
-
-MACHINE_FEATURES:append = " bluetooth wifi"
--- a/conf/machine/include/sun4i.inc
+++ b/conf/machine/include/sun4i.inc
@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/arm/armv7a/tune-cortexa8.inc
+require conf/machine/include/tune-cortexa8.inc

 SOC_FAMILY = "sun4i"
--- a/conf/machine/include/sun50i-h6.inc
+++ b/conf/machine/include/sun50i-h6.inc
@ -1,8 +0,0 @@
-require conf/machine/include/sunxi64.inc
-
-DEFAULTTUNE ?= "cortexa53-crypto"
-require conf/machine/include/arm/armv8a/tune-cortexa53.inc
-
-MACHINEOVERRIDES =. "sun50i:"
-
-SOC_FAMILY = "sun50i-h6"
--- a/conf/machine/include/sun50i-h616.inc
+++ b/conf/machine/include/sun50i-h616.inc
@ -1,8 +0,0 @@
-require conf/machine/include/sunxi64.inc
-
-DEFAULTTUNE ?= "cortexa53-crypto"
-require conf/machine/include/arm/armv8a/tune-cortexa53.inc
-
-MACHINEOVERRIDES =. "sun50i:"
-
-SOC_FAMILY = "sun50i-h616"
--- a/conf/machine/include/sun50i.inc
+++ b/conf/machine/include/sun50i.inc
@ -1,6 +1,6 @@
 require conf/machine/include/sunxi64.inc

 DEFAULTTUNE ?= "cortexa53-crypto"
-require conf/machine/include/arm/armv8a/tune-cortexa53.inc
+require conf/machine/include/tune-cortexa53.inc

 SOC_FAMILY = "sun50i"
--- a/conf/machine/include/sun5i.inc
+++ b/conf/machine/include/sun5i.inc
@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/arm/armv7a/tune-cortexa8.inc
+require conf/machine/include/tune-cortexa8.inc

 SOC_FAMILY = "sun5i"
--- a/conf/machine/include/sun7i.inc
+++ b/conf/machine/include/sun7i.inc
@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/arm/armv7a/tune-cortexa7.inc
+require conf/machine/include/tune-cortexa7.inc

 SOC_FAMILY = "sun7i"
--- a/conf/machine/include/sun8i.inc
+++ b/conf/machine/include/sun8i.inc
@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/arm/armv7a/tune-cortexa7.inc
+require conf/machine/include/tune-cortexa7.inc

 SOC_FAMILY = "sun8i"
--- a/conf/machine/include/sun9i.inc
+++ b/conf/machine/include/sun9i.inc
@ -1,5 +0,0 @@
-require conf/machine/include/sunxi.inc
-require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/arm/armv7a/tune-cortexa15.inc
-
-SOC_FAMILY = "sun9i"
--- a/conf/machine/include/sunxi-mali-driver.inc
+++ b/conf/machine/include/sunxi-mali-driver.inc
@ -4,7 +4,7 @@ PREFERRED_PROVIDER_virtual/libgles1 ?= "sunxi-mali"
 PREFERRED_PROVIDER_virtual/libgles2 ?= "sunxi-mali"
 PREFERRED_PROVIDER_virtual/egl ?= "sunxi-mali"

-PACKAGECONFIG:remove:pn-xserver-xorg = "${@bb.utils.contains('DISTRO_FEATURES', 'x11', 'glamor', '', d)}"
+PACKAGECONFIG_remove_pn-xserver-xorg = "${@bb.utils.contains('DISTRO_FEATURES', 'x11', 'glamor', '', d)}"

 XSERVER += "sunxi-mali \
            sunxi-mali-dev"
--- a/conf/machine/include/sunxi.inc
+++ b/conf/machine/include/sunxi.inc
@ -1,26 +1,26 @@
 SOC_FAMILY ??= ""
 include conf/machine/include/soc-family.inc

-MACHINEOVERRIDES =. "sunxi:"
-
 # Sub-architecture support
 MACHINE_SOCARCH_SUFFIX ?= ""
 MACHINE_SOCARCH_SUFFIX_sun4i = "-sun4i"

 PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
 XSERVER = "xserver-xorg \
+           xf86-video-fbturbo \
           xf86-input-evdev \
           xf86-input-mouse \
           xf86-input-keyboard"

 PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
-PREFERRED_VERSION_linux-mainline ?= "6.6.%"
+PREFERRED_VERSION_linux-mainline ?= "5.4.%"
 PREFERRED_PROVIDER_u-boot ?= "u-boot"
 PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"

 KERNEL_IMAGETYPE ?= "uImage"

-IMAGE_FSTYPES += "ext3 tar.gz wic.gz wic.bmap"
+IMAGE_CLASSES += "sdcard_image-sunxi"
+IMAGE_FSTYPES += "ext3 tar.gz sunxi-sdimg"

 MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"

@ -30,18 +30,5 @@ UBOOT_ENTRYPOINT ?= "0x40008000"

 SPL_BINARY ?= "u-boot-sunxi-with-spl.bin"

-SERIAL_CONSOLES ?= "115200;ttyS0"
+SERIAL_CONSOLE ?= "115200 ttyS0"
 MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"
-
-# Mimic the sdcard_image-sunxi.bbclass
-# image-version-info file was also generated and installed to boot partition,
-# but it is missing here - can be added somehow (how?) if required
-SUNXI_FEX_FILE ?= " "
-SUNXI_BOOT_SPACE ?= "40"
-IMAGE_BOOT_FILES ?= "${KERNEL_IMAGETYPE} boot.scr"
-# ship fex file for sunxi kernel, devicetree file for mainline kernel
-IMAGE_BOOT_FILES += "${@bb.utils.contains('PREFERRED_PROVIDER_virtual/kernel', 'linux-sunxi', '${SUNXI_FEX_FILE}', d.getVar('KERNEL_DEVICETREE', '').split('/')[-1], d)}"
-WKS_FILES ?= "sunxi-sdcard-image.wks.in"
-WKS_FILE_DEPENDS ?= "virtual/kernel u-boot"
-# in case of sunxi kernel, sunxi-board-fex must be built prior wic image assembly
-WKS_FILE_DEPENDS += " ${@bb.utils.contains('PREFERRED_PROVIDER_virtual/kernel', 'linux-sunxi', 'sunxi-board-fex', '', d)}"
--- a/conf/machine/include/sunxi64.inc
+++ b/conf/machine/include/sunxi64.inc
@ -1,32 +1,24 @@
 SOC_FAMILY ??= ""
 include conf/machine/include/soc-family.inc

-MACHINEOVERRIDES =. "sunxi:sunxi64:"
-
 PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
-PREFERRED_VERSION_linux-mainline ?= "6.6.%"
 PREFERRED_PROVIDER_u-boot ?= "u-boot"
 PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"

 KERNEL_IMAGETYPE ?= "Image"

-IMAGE_FSTYPES += "ext4 tar.gz wic.gz wic.bmap"
+IMAGE_CLASSES += "sdcard_image-sunxi"
+IMAGE_FSTYPES += "ext4 tar.gz sunxi-sdimg"

 MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"

 UBOOT_LOCALVERSION = "-g${@d.getVar('SRCPV', True).partition('+')[2][0:7]}"

 UBOOT_ENTRYPOINT ?= "0x40008000"
-UBOOT_LOADADDRESS ?= "0x40008000"
+UBOOT_LOADADDRESS ?= "0x400080OB00"

-#UBOOT_BINARY ?= "u-boot.itb"
-SPL_BINARY ?= "u-boot-sunxi-with-spl.bin"
+UBOOT_BINARY ?= "u-boot.itb"
+SPL_BINARY ?= "spl/sunxi-spl.bin"

-SERIAL_CONSOLES ?= "115200;ttyS0"
+SERIAL_CONSOLE ?= "115200 ttyS0"
 MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"
-
-SUNXI_BOOT_SPACE ?= "40"
-IMAGE_BOOT_FILES ?= "${KERNEL_IMAGETYPE} boot.scr ${@d.getVar('KERNEL_DEVICETREE', '').split('/')[-1]}"
-
-WKS_FILES ?= "sunxi-sdcard-image.wks.in"
-WKS_FILE_DEPENDS ?= "virtual/kernel u-boot"
--- a/conf/machine/lamobo-r1.conf
+++ b/conf/machine/lamobo-r1.conf
@ -1,10 +0,0 @@
-#@TYPE: Machine
-#@NAME: Lamobo R1
-#@DESCRIPTION: Machine configuration for the lamobo r1, based on allwinner A20 CPU http://bananapi.org/
-
-require conf/machine/include/sun7i.inc
-
-MACHINE_EXTRA_RRECOMMENDS = " kernel-modules kernel-devicetree"
-KERNEL_DEVICETREE = "allwinner/sun7i-a20-lamobo-r1.dtb"
-UBOOT_MACHINE = "Lamobo_R1_config"
-SUNXI_FEX_FILE = "sys_config/a20/lamobo-r1.fex"
--- a/conf/machine/licheepi-zero.conf
+++ b/conf/machine/licheepi-zero.conf
@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: licheepi-zero
-#@DESCRIPTION: Machine configuration for the licheepi-zero, based on allwinner V3s CPU
-
-require conf/machine/include/sun8i.inc
-
-
-UBOOT_MACHINE = "LicheePi_Zero_defconfig"
-KERNEL_DEVICETREE = "allwinner/sun8i-v3s-licheepi-zero.dtb"
--- a/conf/machine/mangopi-mq-t-t113.conf
+++ b/conf/machine/mangopi-mq-t-t113.conf
@ -1,10 +0,0 @@
-#@TYPE: Machine
-#@NAME: MangoPi MQ-R T113-S3
-#@DESCRIPTION: Machine configuration for the MangoPi MQ-R, based on the Allwinner T113-S3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-t113s-mangopi-mq-r-t113.dtb"
-KERNEL_IMAGETYPE = "zImage"
-
-UBOOT_MACHINE = "mangopi_mq_r_defconfig"
--- a/conf/machine/marsboard-a10.conf
+++ b/conf/machine/marsboard-a10.conf
@ -1,10 +0,0 @@
-#@TYPE: Machine
-#@NAME: HAOYU Electronics MarsBoard A10
-#@DESCRIPTION: Machine configuration for the HAOYU Electronics MarsBoard A10, based on Allwinner A10 CPU
-#https://linux-sunxi.org/MarsBoard_A10
-
-require conf/machine/include/sun4i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun4i-a10-marsboard.dtb"
-UBOOT_MACHINE = "Marsboard_A10_config"
-SUNXI_FEX_FILE = "sys_config/a10/marsboard_a10.fex"
--- a/conf/machine/mele.conf
+++ b/conf/machine/mele.conf
@ -4,6 +4,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "allwinner/sun4i-a10-a1000.dtb"
+KERNEL_DEVICETREE = "sun4i-a10-a1000.dtb"
 UBOOT_MACHINE = "Mele_A1000_config"
-SUNXI_FEX_FILE = "sys_config/a10/mele_a1000.fex"
+SUNXI_FEX_FILE = "sys_config/a10/mele_a1000.fex"
--- a/conf/machine/merrii-a80-optimus.conf
+++ b/conf/machine/merrii-a80-optimus.conf
@ -1,11 +0,0 @@
-#@TYPE: Machine
-#@NAME: Merrii A80 Optimus
-#@DESCRIPTION: Machine configuration for the Merrii A80 Optimus, based on Allwinner A80 CPU https://linux-sunxi.org/Merrii_A80_Optimus_Board
-
-require conf/machine/include/sun9i.inc
-require conf/machine/include/hardware/ap6330.inc
-
-KERNEL_IMAGETYPE = "zImage"
-
-KERNEL_DEVICETREE = "allwinner/sun9i-a80-optimus.dtb"
-UBOOT_MACHINE = "Merrii_A80_Optimus_defconfig"
--- a/conf/machine/nanopi-m1-plus.conf
+++ b/conf/machine/nanopi-m1-plus.conf
@ -4,5 +4,6 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-m1-plus.dtb"
+KERNEL_DEVICETREE = "sun8i-h3-nanopi-m1-plus.dtb"
 UBOOT_MACHINE = "nanopi_m1_plus_defconfig"
+
--- a/conf/machine/nanopi-m1.conf
+++ b/conf/machine/nanopi-m1.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: NanoPi M1
-#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo, based on #the Allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-m1.dtb"
-UBOOT_MACHINE = "nanopi_m1_defconfig"
--- a/conf/machine/nanopi-neo-air.conf
+++ b/conf/machine/nanopi-neo-air.conf
@ -5,5 +5,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-neo-air.dtb"
+KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo-air.dtb"
 UBOOT_MACHINE = "nanopi_neo_air_defconfig"
--- a/conf/machine/nanopi-neo.conf
+++ b/conf/machine/nanopi-neo.conf
@ -4,5 +4,6 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-neo.dtb"
+KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo.dtb"
 UBOOT_MACHINE = "nanopi_neo_defconfig"
+
--- a/conf/machine/nanopi-r1.conf
+++ b/conf/machine/nanopi-r1.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: NanoPi R1
-#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi R1, based on #the Allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-r1.dtb"
-UBOOT_MACHINE = "nanopi_r1_defconfig"
--- a/conf/machine/olinuxino-a10lime.conf
+++ b/conf/machine/olinuxino-a10lime.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "allwinner/sun4i-a10-olinuxino-lime.dtb"
+KERNEL_DEVICETREE = "sun4i-a10-olinuxino-lime.dtb"
 UBOOT_MACHINE = "A10-OLinuXino-Lime_config"
-SUNXI_FEX_FILE = "sys_config/a10/a10-olinuxino-lime.fex"
+SUNXI_FEX_FILE = "sys_config/a10/a10-olinuxino-lime.fex"
--- a/conf/machine/olinuxino-a10s.conf
+++ b/conf/machine/olinuxino-a10s.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun5i.inc

-KERNEL_DEVICETREE = "allwinner/sun5i-a10s-olinuxino-micro.dtb"
+KERNEL_DEVICETREE = "sun5i-a10s-olinuxino-micro.dtb"
 UBOOT_MACHINE = "A10s-OLinuXino-M_config"
-SUNXI_FEX_FILE = "sys_config/a10s/a10s-olinuxino-m.fex"
+SUNXI_FEX_FILE = "sys_config/a10s/a10s-olinuxino-m.fex"
--- a/conf/machine/olinuxino-a13.conf
+++ b/conf/machine/olinuxino-a13.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun5i.inc

-KERNEL_DEVICETREE = "allwinner/sun5i-a13-olinuxino.dtb"
+KERNEL_DEVICETREE = "sun5i-a13-olinuxino.dtb"
 UBOOT_MACHINE = "A13-OLinuXino_config"
-SUNXI_FEX_FILE = "sys_config/a13/a13-olinuxino.fex"
+SUNXI_FEX_FILE = "sys_config/a13/a13-olinuxino.fex"
--- a/conf/machine/olinuxino-a20.conf
+++ b/conf/machine/olinuxino-a20.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-micro.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-olinuxino-micro.dtb"
 UBOOT_MACHINE = "A20-OLinuXino_MICRO_config"
-SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_micro.fex"
+SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_micro.fex"
--- a/conf/machine/olinuxino-a20lime.conf
+++ b/conf/machine/olinuxino-a20lime.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-lime.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime.dtb"
 UBOOT_MACHINE = "A20-OLinuXino-Lime_config"
-SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime.fex"
+SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime.fex"
--- a/conf/machine/olinuxino-a20lime2-emmc.conf
+++ b/conf/machine/olinuxino-a20lime2-emmc.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-lime2-emmc.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime2-emmc.dtb"
 UBOOT_MACHINE = "A20-OLinuXino-Lime2-eMMC_config"
 SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime2.fex"
--- a/conf/machine/olinuxino-a20lime2.conf
+++ b/conf/machine/olinuxino-a20lime2.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-lime2.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime2.dtb"
 UBOOT_MACHINE = "A20-OLinuXino-Lime2_config"
 SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime2.fex"
--- a/conf/machine/olinuxino-a20som.conf
+++ b/conf/machine/olinuxino-a20som.conf
@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-olimex-som-evb.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-olimex-som-evb.dtb"
 UBOOT_MACHINE = "A20-Olimex-SOM-EVB_config"
 SUNXI_FEX_FILE = "sys_config/a20/olimex_a20_som.fex"
--- a/conf/machine/orange-pi-3lts.conf
+++ b/conf/machine/orange-pi-3lts.conf
@ -1,28 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-3lts
-#@DESCRIPTION: Machine configuration for the Orange Pi 3 LTS , based on Allwinner H6 CPU
-# Note: Some boards have faulty RTC a fix is included by default
-# a workarround in the dts ins include by default but in can removed adding
-# KERNEL_FEATURES:remove = " bsp/orange-pi-3lts/fix-rtc.scc" to local.conf
-
-require conf/machine/include/sun50i-h6.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h6-orangepi-3-lts.dtb"
-UBOOT_MACHINE = "orangepi_3_lts_defconfig"
-
-SPL_BINARY = "u-boot-sunxi-with-spl.bin"
-
-# as for now neither graphics nor audio is supported
-MACHINE_FEATURES:remove = " x11 alsa rtc"
-MACHINE_FEATURES:append = " bluetooth wifi"
-
-# fiwrware needed for wifi + bt
-MACHINE_EXTRA_RRECOMMENDS += " uwe5622-firmware"
-
-# Load modules for wifi & bt
-# Note: fo wifi a custom hci attach userspace sofware is needed that is not included in the layer
-KERNEL_MODULE_AUTOLOAD += " sprdwl_ng sprdbt_tty "
-
-
-
-
--- a/conf/machine/orange-pi-lite.conf
+++ b/conf/machine/orange-pi-lite.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-lite
-#@DESCRIPTION: Machine configuration for the orange-pi-lite, based on Allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-lite.dtb"
-UBOOT_MACHINE = "orangepi_lite_defconfig"
--- a/conf/machine/orange-pi-one-plus.conf
+++ b/conf/machine/orange-pi-one-plus.conf
@ -1,9 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-one-plus
-#@DESCRIPTION: Machine configuration for the Orange Pi One Plus, based on Allwinner H6 CPU
-
-
-require conf/machine/include/sun50i-h6.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h6-orangepi-one-plus.dtb"
-UBOOT_MACHINE = "orangepi_one_plus_defconfig"
--- a/conf/machine/orange-pi-one.conf
+++ b/conf/machine/orange-pi-one.conf
@ -4,5 +4,6 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-one.dtb"
+KERNEL_DEVICETREE = "sun8i-h3-orangepi-one.dtb"
 UBOOT_MACHINE = "orangepi_one_defconfig"
+
--- a/conf/machine/orange-pi-pc-plus.conf
+++ b/conf/machine/orange-pi-pc-plus.conf
@ -4,5 +4,6 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-pc-plus.dtb"
+KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc-plus.dtb"
 UBOOT_MACHINE = "orangepi_pc_plus_defconfig"
+
--- a/conf/machine/orange-pi-pc.conf
+++ b/conf/machine/orange-pi-pc.conf
@ -4,5 +4,6 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-pc.dtb"
+KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc.dtb"
 UBOOT_MACHINE = "orangepi_pc_defconfig"
+
--- a/conf/machine/orange-pi-pc2.conf
+++ b/conf/machine/orange-pi-pc2.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: orangepi-pc2
-#@DESCRIPTION: Machine configuration for the orangepi-pc2, based on Allwinner A64 CPU
-
-require conf/machine/include/sun50i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h5-orangepi-pc2.dtb"
-UBOOT_MACHINE = "orangepi_pc2_defconfig"
--- a/conf/machine/orange-pi-prime.conf
+++ b/conf/machine/orange-pi-prime.conf
@ -1,11 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-prime
-#@DESCRIPTION: Machine configuration for the orange-pi-prime, base on Allwinner H5 CPU
-
-require conf/machine/include/sun50i.inc
-require conf/machine/include/hardware/ap6212a.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h5-orangepi-prime.dtb"
-UBOOT_MACHINE = "orangepi_prime_defconfig"
-
-MACHINE_EXTRA_RRECOMMENDS:append = " linux-firmware-rtl8723"
--- a/conf/machine/orange-pi-r1.conf
+++ b/conf/machine/orange-pi-r1.conf
@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-r1
-#@DESCRIPTION: Machine configuration for the orange-pi-r1, base on allwinner H2+ CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "allwinner/sun8i-h2-plus-orangepi-r1.dtb"
-UBOOT_MACHINE = "orangepi_r1_defconfig"
--- a/conf/machine/orange-pi-zero-plus2-h3.conf
+++ b/conf/machine/orange-pi-zero-plus2-h3.conf
@ -5,5 +5,5 @@
 require conf/machine/include/sun8i.inc
 require conf/machine/include/hardware/ap6212a.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-zero-plus2.dtb"
+KERNEL_DEVICETREE = "sun8i-h3-orangepi-zero-plus2.dtb"
 UBOOT_MACHINE = "orangepi_zero_plus2_h3_defconfig"
--- a/conf/machine/orange-pi-zero.conf
+++ b/conf/machine/orange-pi-zero.conf
@ -1,8 +1,9 @@
 #@TYPE: Machine
-#@NAME: orange-pi-zero
-#@DESCRIPTION: Machine configuration for the orange-pi-zero, based on Allwinner H2 CPU
+#@NAME: orange-pi-one
+#@DESCRIPTION: Machine configuration for the orange-pi-one, base on allwinner H3 CPU

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "allwinner/sun8i-h2-plus-orangepi-zero.dtb"
+KERNEL_DEVICETREE = "sun8i-h2-plus-orangepi-zero.dtb"
 UBOOT_MACHINE = "orangepi_zero_defconfig"
+
--- a/conf/machine/orange-pi-zero2.conf
+++ b/conf/machine/orange-pi-zero2.conf
@ -1,21 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-zero-2
-#@DESCRIPTION: Machine configuration for the orange-pi-zero-2, based on Allwinner H616 CPU
-
-require conf/machine/include/sun50i-h616.inc
-
-KERNEL_DEVICETREE = "allwinner/sun50i-h616-orangepi-zero2.dtb"
-UBOOT_MACHINE = "orangepi_zero2_defconfig"
-
-SPL_BINARY = "u-boot-sunxi-with-spl.bin"
-
-# as for now neither graphics nor audio is supported
-MACHINE_FEATURES:remove = "alsa x11"
-MACHINE_FEATURES:append = "bluetooth wifi"
-
-MACHINE_EXTRA_RRECOMMENDS = "uwe5622-firmware"
-
-# Load modules for wifi & bt
-# Note: fo wifi a custom hci attach userspace sofware is needed that is not included in the layer
-KERNEL_MODULE_AUTOLOAD += " sprdwl_ng sprdbt_tty "
-
--- a/conf/machine/pcduino.conf
+++ b/conf/machine/pcduino.conf
@ -4,6 +4,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "allwinner/sun4i-a10-pcduino.dtb"
+KERNEL_DEVICETREE = "sun4i-a10-pcduino.dtb"
 UBOOT_MACHINE = "Linksprite_pcDuino_defconfig"
 SUNXI_FEX_FILE = "sys_config/a10/pcduino.fex"
--- a/conf/machine/pcduino3.conf
+++ b/conf/machine/pcduino3.conf
@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "allwinner/sun7i-a20-pcduino3.dtb"
+KERNEL_DEVICETREE = "sun7i-a20-pcduino3.dtb"
 UBOOT_MACHINE = "Linksprite_pcDuino3_defconfig"
-SUNXI_FEX_FILE = "sys_config/a20/linksprite_pcduino3.fex"
+SUNXI_FEX_FILE = "sys_config/a20/linksprite_pcduino3.fex"
--- a/recipes-bsp/atf/atf-sunxi_git.bb
+++ b/recipes-bsp/atf/atf-sunxi_git.bb
@ -0,0 +1,27 @@
+DESCRIPTION = "ARM Trusted Firmware Allwinner"
+LICENSE = "BSD"
+LIC_FILES_CHKSUM = "file://license.md;md5=829bdeb34c1d9044f393d5a16c068371"
+
+SRC_URI = "git://github.com/apritzel/arm-trusted-firmware;nobranch=1"
+SRCREV = "aa75c8da415158a94b82a430b2b40000778e851f"
+
+S = "${WORKDIR}/git"
+B = "${WORKDIR}/build"
+
+COMPATIBLE_MACHINE = "(sun50i)"
+
+PLATFORM_sun50i = "sun50iw1p1"
+
+LDFLAGS[unexport] = "1"
+
+do_compile() {
+    oe_runmake -C ${S} BUILD_BASE=${B} \
+      CROSS_COMPILE=${TARGET_PREFIX} \
+      PLAT=${PLATFORM} \
+      bl31 \
+      all
+}
+
+do_install() {
+    install -D -p -m 0644 ${B}/${PLATFORM}/release/bl31.bin ${DEPLOY_DIR_IMAGE}/bl31.bin
+}
--- a/recipes-bsp/sunxi-board-fex/sunxi-board-fex.bb
+++ b/recipes-bsp/sunxi-board-fex/sunxi-board-fex.bb
@ -9,9 +9,9 @@ PR = "r0"

 COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i)"

-SRC_URI = "git://github.com/linux-sunxi/sunxi-boards.git;protocol=https;branch=master"
+SRC_URI = "git://github.com/linux-sunxi/sunxi-boards.git;protocol=git"
 # Increase PV with SRCREV change
-SRCREV = "af5f938ea14a3614d35ad3d9ab51a5d392117444"
+SRCREV = "496ef0fbd166cc2395daa76dd3c359357420963d"

 S = "${WORKDIR}/git"

--- a/recipes-bsp/trusted-firmware-a/trusted-firmware-a_%.bbappend
+++ b/recipes-bsp/trusted-firmware-a/trusted-firmware-a_%.bbappend
@ -1,7 +0,0 @@
-COMPATIBLE_MACHINE:sunxi = "(sun50i|sun50i-h616|sun50i-h6)"
-
-TFA_PLATFORM:sun50i = "sun50i_a64"
-TFA_PLATFORM:sun50i-h6 = "sun50i_h6"
-TFA_PLATFORM:sun50i-h616 = "sun50i_h616"
-
-TFA_BUILD_TARGET:sunxi = "bl31"
--- a/recipes-bsp/u-boot/files/0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch
+++ b/recipes-bsp/u-boot/files/0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch
@ -1,9 +1,9 @@
-From 6a64d90ca4d976c16a2e102dbad0848e4d29776c Mon Sep 17 00:00:00 2001
+From 6adb2ebdc4022c24497e9ee4dccab41d18e3105d Mon Sep 17 00:00:00 2001
 From: Florin Sarbu <florin@resin.io>
 Date: Wed, 12 Sep 2018 14:22:49 +0200
 Subject: [PATCH] nanopi_neo_air_defconfig: Enable eMMC support

-Upstream-Status: Pending
+Upstream-status: Pending
 Signed-off-by: Florin Sarbu <florin@resin.io>

 ---
@ -11,11 +11,11 @@ Signed-off-by: Florin Sarbu <florin@resin.io>
 1 file changed, 1 insertion(+)

 diff --git a/configs/nanopi_neo_air_defconfig b/configs/nanopi_neo_air_defconfig
-index 806d95c1cc..8899cc3a15 100644
+index 5ad90ddd16..8b7a4eb45d 100644
 --- a/configs/nanopi_neo_air_defconfig
 +++ b/configs/nanopi_neo_air_defconfig
-@@ -9,3 +9,4 @@ CONFIG_DRAM_CLK=408
- CONFIG_CONSOLE_MUX=y
+@@ -15,3 +15,4 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-neo-air"
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
+ CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
 +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
--- a/recipes-bsp/u-boot/files/0001-sunxi-board-Fix-early-PMIC-setup-conditions.patch
+++ b/recipes-bsp/u-boot/files/0001-sunxi-board-Fix-early-PMIC-setup-conditions.patch
@ -1,41 +0,0 @@
-From f4dde09fa41eb538b743ee2104c1e2e10cc7e13f Mon Sep 17 00:00:00 2001
-From: Leon Anavi <leon.anavi@konsulko.com>
-Date: Sat, 14 Dec 2024 10:59:09 +0000
-Subject: [PATCH] sunxi: board: Fix early PMIC setup conditions
-
-Patch provided by Andre Przywara through the U-Boot mailing list:
-https://lists.denx.de/pipermail/u-boot/2024-December/575050.html
-
-Upstream-Status: Pending
-
-Suggested-by: Andre Przywara <andre.przywara@arm.com>
-Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
---
- board/sunxi/board.c | 4 +++-
- 1 file changed, 3 insertions(+), 1 deletion(-)
-
-diff --git a/board/sunxi/board.c b/board/sunxi/board.c
-index 961cdcde74..d6759fe853 100644
--- a/board/sunxi/board.c
-+++ b/board/sunxi/board.c
-@@ -577,7 +577,6 @@ void sunxi_board_init(void)
- 
- #ifdef CONFIG_AXP_DCDC1_VOLT
- 	power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
-	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
- #endif
- #ifdef CONFIG_AXP_DCDC2_VOLT
- 	power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
-@@ -586,6 +585,9 @@ void sunxi_board_init(void)
- #ifdef CONFIG_AXP_DCDC4_VOLT
- 	power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
- #endif
-+#ifdef CONFIG_AXP_DCDC5_VOLT
-+	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
-+#endif
- 
- #ifdef CONFIG_AXP_ALDO1_VOLT
- 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
-- 
-2.47.1
-
--- a/recipes-bsp/u-boot/files/0002-Added-nanopi-r1-board-support.patch
+++ b/recipes-bsp/u-boot/files/0002-Added-nanopi-r1-board-support.patch
@ -1,42 +0,0 @@
-From 767a05572ef5b93c2e157749b1754cbe261ee43d Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@open-nandra.com>
-Date: Fri, 8 Apr 2022 11:33:53 +0200
-Subject: [PATCH] Added nanopi-r1 board support
-
-Patch taken from : https://github.com/armbian/build/blob/master/patch/u-boot/u-boot-sunxi/add-nanopi-r1-and-duo2.patch
-
-Upstream-Status: Pending
-
-Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
---
-diff --git a/configs/nanopi_r1_defconfig b/configs/nanopi_r1_defconfig
-new file mode 100644
-index 0000000..e028b41
--- /dev/null
-+++ b/configs/nanopi_r1_defconfig
-@@ -0,0 +1,22 @@
-+CONFIG_ARM=y
-+CONFIG_ARCH_SUNXI=y
-+CONFIG_SPL=y
-+CONFIG_MACH_SUN8I_H3=y
-+CONFIG_DRAM_CLK=408
-+CONFIG_DRAM_ZQ=3881979
-+CONFIG_DRAM_ODT_EN=y
-+CONFIG_MACPWR="PD6"
-+# CONFIG_VIDEO_DE2 is not set
-+CONFIG_NR_DRAM_BANKS=1
-+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-+CONFIG_CONSOLE_MUX=y
-+CONFIG_SYS_CLK_FREQ=480000000
-+# CONFIG_CMD_FLASH is not set
-+# CONFIG_SPL_DOS_PARTITION is not set
-+# CONFIG_SPL_EFI_PARTITION is not set
-+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-r1"
-+CONFIG_SUN8I_EMAC=y
-+CONFIG_USB_EHCI_HCD=y
-+CONFIG_USB_OHCI_HCD=y
-+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
-+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
-- 
-2.7.4
-
--- a/recipes-bsp/u-boot/files/0003-sunxi-H6-Enable-Ethernet-on-Orange-Pi-One-Plus.patch
+++ b/recipes-bsp/u-boot/files/0003-sunxi-H6-Enable-Ethernet-on-Orange-Pi-One-Plus.patch
@ -1,58 +0,0 @@
-From: Anne Macedo <retpolanne@posteo.net>
-Date: Tue, 11 Jul 2023 00:39:58 +0000
-Subject: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus
-
-Enable Ethernet on Orange Pi One Plus by using the correct phy for
-Realtek RTL8211E instead of the Generic One. Also use CONFIG_MACPWR to
-turn on ethernet on startup.
-
-After this patch is applied, a few issues can be seen:
-
- there's still a PHY reset timed out error that doesn't seem to cause
-  any impacts to the overall connection
-
- sometimes the emac driver times out after reset (yellow LED turns on
-  and never blinks)
-
-For future patches: for now, CONFIG_MACPWR is the only way to enable
-Ethernet on boot. There's already code on the dts for using the 3v3-gmac
-regulator. However, it is not probed on boot, so it only starts after a
-"regulator status" command is issued.
-
-More details about the troubleshooting on [1].
-
-Upstream-Status: Submitted
-
-[1] https://lore.kernel.org/u-boot/4wsvwgy56e2xfgtvioru2tf2ofkqprlts36qggivxogww6pn5j@4jk63zxhzhag/
-
-Signed-off-by: Anne Macedo <retpolanne@posteo.net>
---
- arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 2 +-
- configs/orangepi_one_plus_defconfig          | 4 ++++
- 2 files changed, 5 insertions(+), 1 deletion(-)
-
-diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
-index 29a081e72a..6427c58f8a 100644
--- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
-+++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
-@@ -37,7 +37,7 @@
- 
- &mdio {
- 	ext_rgmii_phy: ethernet-phy@1 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-+		compatible = "ethernet-phy-id001c.c915", "ethernet-phy-ieee802.3-c22" ;
- 		reg = <1>;
- 	};
- };
-diff --git a/configs/orangepi_one_plus_defconfig b/configs/orangepi_one_plus_defconfig
-index aa5f540eb1..a1835492db 100644
--- a/configs/orangepi_one_plus_defconfig
-+++ b/configs/orangepi_one_plus_defconfig
-@@ -8,3 +8,7 @@ CONFIG_SUNXI_DRAM_H6_LPDDR3=y
- # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
- CONFIG_USB_EHCI_HCD=y
- CONFIG_USB_OHCI_HCD=y
-+CONFIG_SUN8I_EMAC=y
-+CONFIG_PHY_REALTEK=y
-+CONFIG_PHY_ETHERNET_ID=y
-+CONFIG_MACPWR="PD6"
--- a/recipes-bsp/u-boot/files/0004-OrangePi-3-LTS-support.patch
+++ b/recipes-bsp/u-boot/files/0004-OrangePi-3-LTS-support.patch
@ -1,421 +0,0 @@
-From 9966dda20246285abf8b417bd251d5a4bea3e423 Mon Sep 17 00:00:00 2001
-From: Juliano Dorigão <jdorigao@gmail.com>
-Date: Fri, 3 Mar 2023 16:11:30 -0400
-Subject: [PATCH] OrangePi 3 LTS support
-
-Upstream-Status: Pending
---
- arch/arm/dts/Makefile                     |   1 +
- arch/arm/dts/sun50i-h6-orangepi-3-lts.dts | 361 ++++++++++++++++++++++
- configs/orangepi_3_lts_defconfig          |  19 ++
- 3 files changed, 381 insertions(+)
- create mode 100644 arch/arm/dts/sun50i-h6-orangepi-3-lts.dts
- create mode 100644 configs/orangepi_3_lts_defconfig
-
-diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
-index 43951a77..8dbbb6f4 100644
--- a/arch/arm/dts/Makefile
-+++ b/arch/arm/dts/Makefile
-@@ -710,6 +710,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
- dtb-$(CONFIG_MACH_SUN50I_H6) += \
- 	sun50i-h6-beelink-gs1.dtb \
- 	sun50i-h6-orangepi-3.dtb \
-+	sun50i-h6-orangepi-3-lts.dtb \
- 	sun50i-h6-orangepi-lite2.dtb \
- 	sun50i-h6-orangepi-one-plus.dtb \
- 	sun50i-h6-pine-h64.dtb \
-diff --git a/arch/arm/dts/sun50i-h6-orangepi-3-lts.dts b/arch/arm/dts/sun50i-h6-orangepi-3-lts.dts
-new file mode 100644
-index 00000000..67f38b8a
--- /dev/null
-+++ b/arch/arm/dts/sun50i-h6-orangepi-3-lts.dts
-@@ -0,0 +1,361 @@
-+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-+// Copyright (C) 2023 Jernej Skrabec <jernej.skrabec@gmail.com>
-+// Based on sun50i-h6-orangepi-3.dts, which is:
-+// Copyright (C) 2019 Ondřej Jirman <megous@megous.com>
-+
-+/dts-v1/;
-+
-+#include "sun50i-h6.dtsi"
-+#include "sun50i-h6-cpu-opp.dtsi"
-+
-+#include <dt-bindings/gpio/gpio.h>
-+
-+/ {
-+	model = "OrangePi 3 LTS";
-+	compatible = "xunlong,orangepi-3-lts", "allwinner,sun50i-h6";
-+
-+	aliases {
-+		ethernet0 = &emac;
-+		serial0 = &uart0;
-+	};
-+
-+	chosen {
-+		stdout-path = "serial0:115200n8";
-+	};
-+
-+	connector {
-+		compatible = "hdmi-connector";
-+		ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
-+		type = "a";
-+
-+		port {
-+			hdmi_con_in: endpoint {
-+				remote-endpoint = <&hdmi_out_con>;
-+			};
-+		};
-+	};
-+
-+	ext_osc32k: ext_osc32k_clk {
-+		#clock-cells = <0>;
-+		compatible = "fixed-clock";
-+		clock-frequency = <32768>;
-+		clock-output-names = "ext_osc32k";
-+	};
-+
-+	leds {
-+		compatible = "gpio-leds";
-+
-+		led-0 {
-+			label = "orangepi:red:power";
-+			gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
-+		};
-+
-+		led-1 {
-+			label = "orangepi:green:status";
-+			gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
-+			default-state = "on";
-+		};
-+	};
-+
-+	reg_vcc5v: vcc5v {
-+		/* board wide 5V supply directly from the DC jack */
-+		compatible = "regulator-fixed";
-+		regulator-name = "vcc-5v";
-+		regulator-min-microvolt = <5000000>;
-+		regulator-max-microvolt = <5000000>;
-+		regulator-always-on;
-+	};
-+
-+	reg_gmac_3v3: gmac-3v3 {
-+		compatible = "regulator-fixed";
-+		regulator-name = "gmac-3v3";
-+		regulator-min-microvolt = <3300000>;
-+		regulator-max-microvolt = <3300000>;
-+		startup-delay-us = <150000>;
-+		enable-active-high;
-+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
-+	};
-+
-+	reg_vcc33_wifi: vcc33-wifi {
-+		/* Always on 3.3V regulator for WiFi and BT */
-+		compatible = "regulator-fixed";
-+		regulator-name = "vcc33-wifi";
-+		regulator-min-microvolt = <3300000>;
-+		regulator-max-microvolt = <3300000>;
-+		enable-active-high;
-+		gpio = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
-+	};
-+
-+	reg_vcc_wifi_io: vcc-wifi-io {
-+		/* Always on 1.8V/300mA regulator for WiFi and BT IO */
-+		compatible = "regulator-fixed";
-+		regulator-name = "vcc-wifi-io";
-+		regulator-min-microvolt = <1800000>;
-+		regulator-max-microvolt = <1800000>;
-+		regulator-always-on;
-+		vin-supply = <&reg_vcc33_wifi>;
-+	};
-+
-+	wifi_pwrseq: wifi-pwrseq {
-+		compatible = "mmc-pwrseq-simple";
-+		clocks = <&rtc 1>;
-+		clock-names = "ext_clock";
-+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
-+		post-power-on-delay-ms = <200>;
-+	};
-+};
-+
-+&cpu0 {
-+	cpu-supply = <&reg_dcdca>;
-+};
-+
-+&de {
-+	status = "okay";
-+};
-+
-+&dwc3 {
-+	status = "okay";
-+};
-+
-+&ehci0 {
-+	status = "okay";
-+};
-+
-+&ehci3 {
-+	status = "okay";
-+};
-+
-+&emac {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&ext_rgmii_pins>;
-+	phy-mode = "rgmii";
-+	phy-handle = <&ext_rgmii_phy>;
-+	phy-supply = <&reg_gmac_3v3>;
-+	allwinner,rx-delay-ps = <1500>;
-+	allwinner,tx-delay-ps = <700>;
-+	status = "okay";
-+};
-+
-+&gpu {
-+	mali-supply = <&reg_dcdcc>;
-+	status = "okay";
-+};
-+
-+&hdmi {
-+	hvcc-supply = <&reg_bldo2>;
-+	status = "okay";
-+};
-+
-+&hdmi_out {
-+	hdmi_out_con: endpoint {
-+		remote-endpoint = <&hdmi_con_in>;
-+	};
-+};
-+
-+&mdio {
-+	ext_rgmii_phy: ethernet-phy@1 {
-+		compatible = "ethernet-phy-ieee802.3-c22";
-+		reg = <1>;
-+
-+		reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
-+		reset-assert-us = <15000>;
-+		reset-deassert-us = <40000>;
-+	};
-+};
-+
-+&mmc0 {
-+	vmmc-supply = <&reg_cldo1>;
-+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
-+	bus-width = <4>;
-+	status = "okay";
-+};
-+
-+&mmc1 {
-+	vmmc-supply = <&reg_vcc33_wifi>;
-+	vqmmc-supply = <&reg_vcc_wifi_io>;
-+	mmc-pwrseq = <&wifi_pwrseq>;
-+	bus-width = <4>;
-+	non-removable;
-+	status = "okay";
-+};
-+
-+&mmc2 {
-+	vmmc-supply = <&reg_cldo1>;
-+	vqmmc-supply = <&reg_bldo2>;
-+	cap-mmc-hw-reset;
-+	non-removable;
-+	bus-width = <8>;
-+	status = "okay";
-+};
-+
-+&ohci0 {
-+	status = "okay";
-+};
-+
-+&ohci3 {
-+	status = "okay";
-+};
-+
-+&pio {
-+	vcc-pc-supply = <&reg_bldo2>;
-+	vcc-pd-supply = <&reg_cldo1>;
-+	vcc-pg-supply = <&reg_bldo3>;
-+};
-+
-+&r_ir {
-+	status = "okay";
-+};
-+
-+&r_rsb {
-+	clock-frequency = <100000>;
-+	status = "okay";
-+
-+	axp805: pmic@745 {
-+		compatible = "x-powers,axp805", "x-powers,axp806";
-+		reg = <0x745>;
-+		interrupt-parent = <&r_intc>;
-+		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
-+		interrupt-controller;
-+		#interrupt-cells = <1>;
-+		x-powers,self-working-mode;
-+		vina-supply = <&reg_vcc5v>;
-+		vinb-supply = <&reg_vcc5v>;
-+		vinc-supply = <&reg_vcc5v>;
-+		vind-supply = <&reg_vcc5v>;
-+		vine-supply = <&reg_vcc5v>;
-+		aldoin-supply = <&reg_vcc5v>;
-+		bldoin-supply = <&reg_vcc5v>;
-+		cldoin-supply = <&reg_vcc5v>;
-+
-+		regulators {
-+			reg_aldo1: aldo1 {
-+				regulator-always-on;
-+				regulator-min-microvolt = <3300000>;
-+				regulator-max-microvolt = <3300000>;
-+				regulator-name = "vcc-pl-led-ir";
-+			};
-+
-+			reg_aldo2: aldo2 {
-+				regulator-min-microvolt = <3300000>;
-+				regulator-max-microvolt = <3300000>;
-+				regulator-name = "vcc33-audio-tv-ephy-mac";
-+			};
-+
-+			/* ALDO3 is shorted to CLDO1 */
-+			reg_aldo3: aldo3 {
-+				regulator-always-on;
-+				regulator-min-microvolt = <3300000>;
-+				regulator-max-microvolt = <3300000>;
-+				regulator-name = "vcc33-io-pd-emmc-sd-usb-uart-1";
-+			};
-+
-+			reg_bldo1: bldo1 {
-+				regulator-always-on;
-+				regulator-min-microvolt = <1800000>;
-+				regulator-max-microvolt = <1800000>;
-+				regulator-name = "vcc18-dram-bias-pll";
-+			};
-+
-+			reg_bldo2: bldo2 {
-+				regulator-min-microvolt = <1800000>;
-+				regulator-max-microvolt = <1800000>;
-+				regulator-name = "vcc-efuse-pcie-hdmi-pc";
-+			};
-+
-+			reg_bldo3: bldo3 {
-+				regulator-min-microvolt = <1800000>;
-+				regulator-max-microvolt = <1800000>;
-+				regulator-name = "vcc-pm-pg-dcxoio-wifi";
-+			};
-+
-+			bldo4 {
-+				/* unused */
-+			};
-+
-+			reg_cldo1: cldo1 {
-+				regulator-always-on;
-+				regulator-min-microvolt = <3300000>;
-+				regulator-max-microvolt = <3300000>;
-+				regulator-name = "vcc33-io-pd-emmc-sd-usb-uart-2";
-+			};
-+
-+			cldo2 {
-+				/* unused */
-+			};
-+
-+			cldo3 {
-+				/* unused */
-+			};
-+
-+			reg_dcdca: dcdca {
-+				regulator-always-on;
-+				regulator-min-microvolt = <800000>;
-+				regulator-max-microvolt = <1160000>;
-+				regulator-ramp-delay = <2500>;
-+				regulator-name = "vdd-cpu";
-+			};
-+
-+			reg_dcdcc: dcdcc {
-+				regulator-enable-ramp-delay = <32000>;
-+				regulator-min-microvolt = <810000>;
-+				regulator-max-microvolt = <1080000>;
-+				regulator-ramp-delay = <2500>;
-+				regulator-name = "vdd-gpu";
-+			};
-+
-+			reg_dcdcd: dcdcd {
-+				regulator-always-on;
-+				regulator-min-microvolt = <980000>;
-+				regulator-max-microvolt = <980000>;
-+				regulator-name = "vdd-sys";
-+			};
-+
-+			reg_dcdce: dcdce {
-+				regulator-always-on;
-+				regulator-min-microvolt = <1200000>;
-+				regulator-max-microvolt = <1200000>;
-+				regulator-name = "vcc-dram";
-+			};
-+
-+			sw {
-+				/* unused */
-+			};
-+		};
-+	};
-+};
-+
-+&pwm {
-+	status = "okay";
-+};
-+
-+&r_ir {
-+	status = "okay";
-+};
-+
-+&rtc {
-+	clocks = <&ext_osc32k>;
-+};
-+
-+/delete-node/ &spi0;
-+
-+&uart0 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&uart0_ph_pins>;
-+	status = "okay";
-+};
-+
-+&usb2otg {
-+	dr_mode = "host";
-+	status = "okay";
-+};
-+
-+&usb2phy {
-+	usb0_id_det-gpios = <&pio 2 15 GPIO_ACTIVE_HIGH>; /* PC15 */
-+	usb0_vbus-supply = <&reg_vcc5v>;
-+	usb3_vbus-supply = <&reg_vcc5v>;
-+	status = "okay";
-+};
-+
-+&usb3phy {
-+	status = "okay";
-+};
-diff --git a/configs/orangepi_3_lts_defconfig b/configs/orangepi_3_lts_defconfig
-new file mode 100644
-index 00000000..41a9af4e
--- /dev/null
-+++ b/configs/orangepi_3_lts_defconfig
-@@ -0,0 +1,19 @@
-+CONFIG_ARM=y
-+CONFIG_ARCH_SUNXI=y
-+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-orangepi-3-lts"
-+CONFIG_SPL=y
-+CONFIG_MACH_SUN50I_H6=y
-+CONFIG_SUNXI_DRAM_H6_LPDDR3=y
-+CONFIG_MMC0_CD_PIN="PF6"
-+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
-+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-+CONFIG_SPL_STACK=0x118000
-+CONFIG_SYS_PBSIZE=1024
-+CONFIG_SYS_BOOTM_LEN=0x2000000
-+CONFIG_PHY_SUN50I_USB3=y
-+CONFIG_USB_XHCI_HCD=y
-+CONFIG_USB_XHCI_DWC3=y
-+CONFIG_USB_EHCI_HCD=y
-+CONFIG_USB_OHCI_HCD=y
-+CONFIG_USB_DWC3=y
-+# CONFIG_USB_DWC3_GADGET is not set
-- 
-2.39.2
-
--- a/recipes-bsp/u-boot/files/0004-mangopi-mq-r-t113-Fix-serial-console.patch
+++ b/recipes-bsp/u-boot/files/0004-mangopi-mq-r-t113-Fix-serial-console.patch
@ -1,30 +0,0 @@
-From bf813915bf480154c707e0be14016cef94adbd95 Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@gmail.com>
-Date: Tue, 7 May 2024 11:27:08 +0200
-Subject: [PATCH] mangopi-mq-r-t113: Fix serial console
-
-Serial console is on uart3 not on uart0.
-
-Upstream-Status: Inappropriate (for this board only)
-
-Signed-off-by: Marek Belisko <marek.belisko@gmail.com>
---
- include/configs/sunxi-common.h | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
-diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
-index b8ca77d031..4e4808d2c1 100644
--- a/include/configs/sunxi-common.h
-+++ b/include/configs/sunxi-common.h
-@@ -324,7 +324,7 @@
- 	MEM_LAYOUT_ENV_EXTRA_SETTINGS \
- 	DFU_ALT_INFO_RAM \
- 	"fdtfile=" FDTFILE "\0" \
-	"console=ttyS0,115200\0" \
-+	"console=ttyS3,115200\0" \
- 	"uuid_gpt_esp=" UUID_GPT_ESP "\0" \
- 	"uuid_gpt_system=" UUID_GPT_SYSTEM "\0" \
- 	"partitions=" PARTS_DEFAULT "\0" \
-- 
-2.25.1
-
--- a/recipes-bsp/u-boot/files/arm/boot.cmd
+++ b/recipes-bsp/u-boot/files/arm/boot.cmd
@ -6,6 +6,6 @@ if itest.b *0x28 == 0x02 ; then
 	rootdev=mmcblk1p2
 fi
 setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
-load mmc 0:1 ${fdt_addr_r} ${fdtfile} || load mmc 0:1 ${fdt_addr_r} boot/allwinner/${fdtfile}
+load mmc 0:1 ${fdt_addr_r} ${fdtfile} || load mmc 0:1 ${fdt_addr_r} boot/${fdtfile}
 load mmc 0:1 ${kernel_addr_r} zImage || load mmc 0:1 ${kernel_addr_r} boot/zImage || load mmc 0:1 ${kernel_addr_r} uImage || load mmc 0:1 ${kernel_addr_r} boot/uImage
 bootz ${kernel_addr_r} - ${fdt_addr_r} || bootm ${kernel_addr_r} - ${fdt_addr_r}
--- a/recipes-bsp/u-boot/files/bananapi-m64/boot.cmd
+++ b/recipes-bsp/u-boot/files/bananapi-m64/boot.cmd
@ -1,11 +0,0 @@
-# Default to (primary) SD
-rootdev=mmcblk0p2
-if itest.b *0x28 == 0x02 ; then
-	# U-Boot loaded from eMMC or secondary SD so use it for rootfs too
-	echo "U-boot loaded from eMMC or secondary SD"
-	rootdev=mmcblk2p2
-fi
-setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
-load mmc 0:1 ${fdt_addr_r} ${fdtfile}
-load mmc 0:1 ${kernel_addr_r} Image
-booti ${kernel_addr_r} - ${fdt_addr_r}
--- a/recipes-bsp/u-boot/u-boot-sunxi.bb
+++ b/recipes-bsp/u-boot/u-boot-sunxi.bb
@ -2,7 +2,7 @@ DESCRIPTION = "U-Boot port for sunxi"

 require recipes-bsp/u-boot/u-boot.inc

-LICENSE = "GPL-2.0-only"
+LICENSE = "GPLv2"
 LIC_FILES_CHKSUM = "file://Licenses/gpl-2.0.txt;md5=b234ee4d69f5fce4486a80fdaf4a4263"

 # No patches for other machines yet
@ -19,7 +19,7 @@ UBOOT_MACHINE_olinuxino-a10s = "A10s-OLinuXino-Micro_config"
 UBOOT_MACHINE_meleg = "Mele_A1000G_config"

 SRC_URI = " \
-	git://github.com/linux-sunxi/u-boot-sunxi.git;protocol=https;branch=sunxi \
+	git://github.com/linux-sunxi/u-boot-sunxi.git;protocol=git;branch=sunxi \
 	file://0001-gcc5-fixes.patch \
 	file://0002-gcc6-fixes.patch \
 	file://0003-No-gcc-version-specific-includes.patch \
--- a/recipes-bsp/u-boot/u-boot_%.bbappend
+++ b/recipes-bsp/u-boot/u-boot_%.bbappend
@ -1,39 +1,29 @@
-FILESEXTRAPATHS:prepend:sunxi := "${THISDIR}/files:"
+FILESEXTRAPATHS_prepend := "${THISDIR}/files:"

-DEPENDS:append:sunxi = " bc-native dtc-native swig-native python3-native flex-native bison-native "
-DEPENDS:append:sun50i = " trusted-firmware-a"
+DEPENDS += " bc-native dtc-native swig-native python3-native flex-native bison-native "
+DEPENDS_append_sun50i = " atf-sunxi "

-COMPATIBLE_MACHINE:sunxi = "(sun4i|sun5i|sun7i|sun8i|sun9i|sun50i)"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"

-DEFAULT_PREFERENCE:sun4i = "1"
-DEFAULT_PREFERENCE:sun5i = "1"
-DEFAULT_PREFERENCE:sun7i = "1"
-DEFAULT_PREFERENCE:sun8i = "1"
-DEFAULT_PREFERENCE:sun50i = "1"
+DEFAULT_PREFERENCE_sun4i="1"
+DEFAULT_PREFERENCE_sun5i="1"
+DEFAULT_PREFERENCE_sun7i="1"
+DEFAULT_PREFERENCE_sun8i="1"
+DEFAULT_PREFERENCE_sun50i="1"

-SRC_URI:append:sunxi = " \
-    file://0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch \
-    file://0002-Added-nanopi-r1-board-support.patch \
-    file://0003-sunxi-H6-Enable-Ethernet-on-Orange-Pi-One-Plus.patch \
-    file://0004-OrangePi-3-LTS-support.patch \
-    file://boot.cmd \
-"
-SRC_URI:append:sun9i = " \
-    file://0001-sunxi-board-Fix-early-PMIC-setup-conditions.patch \
-"
+SRC_URI += " \
+           file://0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch \
+           file://boot.cmd \
+           "

-SRC_URI:append:mangopi-mq-t-t113 = " \
-    file://0004-mangopi-mq-r-t113-Fix-serial-console.patch \
-    "
+UBOOT_ENV_SUFFIX = "scr"
+UBOOT_ENV = "boot"

-UBOOT_ENV_SUFFIX:sunxi = "scr"
-UBOOT_ENV:sunxi = "boot"
+EXTRA_OEMAKE += ' HOSTLDSHARED="${BUILD_CC} -shared ${BUILD_LDFLAGS} ${BUILD_CFLAGS}" '
+EXTRA_OEMAKE_append_sun50i = " BL31=${DEPLOY_DIR_IMAGE}/bl31.bin "

-EXTRA_OEMAKE:append:sunxi = ' HOSTLDSHARED="${BUILD_CC} -shared ${BUILD_LDFLAGS} ${BUILD_CFLAGS}" '
-EXTRA_OEMAKE:append:sun50i = " BL31=${DEPLOY_DIR_IMAGE}/bl31.bin SCP=/dev/null"
+do_compile_sun50i[depends] += "atf-sunxi:do_deploy"

-do_compile:sun50i[depends] += "trusted-firmware-a:do_deploy"
-
-do_compile:append:sunxi() {
-    ${B}/tools/mkimage -C none -A arm -T script -d ${UNPACKDIR}/boot.cmd ${UNPACKDIR}/${UBOOT_ENV_BINARY}
+do_compile_append() {
+    ${B}/tools/mkimage -C none -A arm -T script -d ${WORKDIR}/boot.cmd ${WORKDIR}/${UBOOT_ENV_BINARY}
 }
--- a/recipes-devtools/python/files/olinuxino-a20lime2-emmc
+++ b/recipes-devtools/python/files/olinuxino-a20lime2-emmc
@ -1 +0,0 @@
-/home/marek/data/projects/kas/sources/meta-sunxi/recipes-devtools/python/files/olinuxino-a20lime2
--- a/recipes-devtools/python/pya20_0.2.12.bb
+++ b/recipes-devtools/python/pya20_0.2.12.bb
@ -1,7 +1,7 @@
 DESCRIPTION = "A module to control Allwinner GPIO,SPI and I2C channels"
 HOMEPAGE = "https://pypi.python.org/pypi/pyA20"
 SECTION = "devel/python"
-LICENSE = "GPL-3.0-only"
+LICENSE = "GPLv3"
 LIC_FILES_CHKSUM = "file://PKG-INFO;md5=4e584373bb0f46ef1e423cb7df37847d"
 DEPENDS = "python3"

@ -13,10 +13,10 @@ SRC_URI = "https://pypi.python.org/packages/source/p/pyA20/pyA20-${PV}.tar.gz \
          "
 S = "${WORKDIR}/pyA20-${PV}"

-inherit setuptools3
+inherit distutils3

-do_compile:prepend() { 
-    cp ${UNPACKDIR}/mapping.h ${S}/pyA20/gpio/mapping.h
+do_compile_prepend() { 
+cp ${WORKDIR}/mapping.h ${S}/pyA20/gpio/mapping.h
 }

 SRC_URI[md5sum] = "cab03b4931199804603d1074f6d8f48f"
--- a/recipes-graphics/libgles/sunxi-mali_git.bb
+++ b/recipes-graphics/libgles/sunxi-mali_git.bb
@ -21,8 +21,8 @@ python __anonymous() {
        raise bb.parse.SkipPackage("%s-%s ONLY supports hardfp mode for now" % (pkgn, pkgv))
 }

-SRCREV = "d343311efc8db166d8371b28494f0f27b6a58724"
-SRC_URI = "git://github.com/linux-sunxi/sunxi-mali.git;protocol=https;branch=master \
+SRCREV_pn-${PN} = "d343311efc8db166d8371b28494f0f27b6a58724"
+SRC_URI = "gitsm://github.com/linux-sunxi/sunxi-mali.git \
           file://0001-Add-EGLSyncKHR-EGLTimeKHR-and-GLChar-definition.patch \
           file://0002-Add-missing-GLchar-definition.patch \
           file://0003-Fix-sed-to-replace-by-the-correct-var.patch \
@ -92,13 +92,13 @@ do_install() {
 # Packages like xf86-video-fbturbo dlopen() libUMP.so, so we do need to ship the .so files in ${PN}
 PACKAGES =+ "${PN}-test"

-RPROVIDES:${PN} += "libGLESv2.so libEGL.so libGLESv2.so libGLESv1_CM.so libMali.so"
-RDEPENDS:${PN}-test = "${PN}"
+RPROVIDES_${PN} += "libGLESv2.so libEGL.so libGLESv2.so libGLESv1_CM.so libMali.so"
+RDEPENDS_${PN}-test = "${PN}"

-FILES:${PN} += "${libdir}/lib*.so"
-FILES:${PN}-dev = "${includedir} ${libdir}/pkgconfig/*"
-FILES:${PN}-test = "${bindir}/sunximali-test"
+FILES_${PN} += "${libdir}/lib*.so"
+FILES_${PN}-dev = "${includedir} ${libdir}/pkgconfig/*"
+FILES_${PN}-test = "${bindir}/sunximali-test"

 # These are closed binaries generated elsewhere so don't check ldflags & text relocations
-INSANE_SKIP:${PN} = "dev-so ldflags textrel"
-INSANE_SKIP:${PN}-test = "dev-so ldflags textrel"
+INSANE_SKIP_${PN} = "dev-so ldflags textrel"
+INSANE_SKIP_${PN}-test = "dev-so ldflags textrel"
--- a/recipes-graphics/libump/libump_git.bb
+++ b/recipes-graphics/libump/libump_git.bb
@ -1,14 +1,14 @@
 DESCRIPTION = "Unified Memory Provider userspace API source code needed for xf86-video-mali compilation"

-LICENSE = "Apache-2.0"
+LICENSE = "Apache-2"
 LIC_FILES_CHKSUM = "file://debian/copyright;md5=edf7fb6071cae7ec80d537a05ee17198"

 inherit autotools

 PV = "r4p0-00rel0+git${SRCPV}"
-SRCREV = "ec0680628744f30b8fac35e41a7bd8e23e59c39f"
+SRCREV_pn-${PN} = "ec0680628744f30b8fac35e41a7bd8e23e59c39f"

-SRC_URI = "git://github.com/linux-sunxi/libump.git;protocol=https;branch=master"
+SRC_URI = "git://github.com/linux-sunxi/libump.git"

 S = "${WORKDIR}/git"

--- a/recipes-graphics/mesa/mesa-gl.bbappend
+++ b/recipes-graphics/mesa/mesa-gl.bbappend
@ -1 +0,0 @@
-PACKAGECONFIG:class-target = "opengl x11 gallium"
--- a/recipes-graphics/mesa/mesa_%.bbappend
+++ b/recipes-graphics/mesa/mesa_%.bbappend
@ -1,5 +1,5 @@
 # Enable lima and panfrost Mesa drivers
-PACKAGECONFIG:append:use-mailine-graphics = " lima panfrost"
+PACKAGECONFIG_append_use-mailine-graphics = " lima panfrost"
 # Enable KMS renderonly Mesa support
 # See https://cgit.freedesktop.org/mesa/mesa/commit/?id=2b780fe89300199f2334539aa1678e9b68f0434f
-GALLIUMDRIVERS:append:use-mailine-graphics = ",kmsro"
+GALLIUMDRIVERS_append_use-mailine-graphics = ",kmsro"
--- a/recipes-graphics/tslib/tslib_1.1.bbappend.disabled
+++ b/recipes-graphics/tslib/tslib_1.1.bbappend.disabled
@ -1,4 +1,4 @@
-FILESEXTRAPATHS:prepend := "${THISDIR}/${PN}:"
+FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}:"

 SRC_URI += "file://tslib.patch"

--- a/recipes-graphics/xorg-xserver/libdri2_git.bb
+++ b/recipes-graphics/xorg-xserver/libdri2_git.bb
@ -1,6 +1,6 @@
 DESCRIPTION = "Library for the DRI2 extension to the X Window System"

-LICENSE = "MIT-CMU"
+LICENSE = "MIT-X"
 LIC_FILES_CHKSUM = "file://COPYING;md5=827da9afab1f727f2a66574629e0f39c"

 DEPENDS = "libdrm libxext libxfixes xorgproto"
@ -9,7 +9,7 @@ PE = "1"
 PV = "1.0.0+git${SRCPV}"
 SRC_URI = "git://github.com/robclark/libdri2.git;protocol=http;branch=master"

-SRCREV = "4f1eef3183df2b270c3d5cbef07343ee5127a6a4"
+SRCREV_pn-${PN} = "4f1eef3183df2b270c3d5cbef07343ee5127a6a4"

 S = "${WORKDIR}/git"

--- a/recipes-graphics/xorg-xserver/xf86-video-fbturbo_git.bb
+++ b/recipes-graphics/xorg-xserver/xf86-video-fbturbo_git.bb
@ -2,14 +2,14 @@ require recipes-graphics/xorg-driver/xorg-driver-video.inc

 DESCRIPTION = "X.Org X server -- A10/A13 display driver"

-LICENSE = "MIT-CMU"
+LICENSE = "MIT-X"
 LIC_FILES_CHKSUM = "file://COPYING;md5=f91dc3ee5ce59eb4b528e67e98a31266"

 DEPENDS += "sunxi-mali libump xorgproto"

 PE = "3"
 PV = "0.5.1+git${SRCPV}"
-SRCREV = "e094e3c8f9004ca3347694bd05b99d136e8621b9"
+SRCREV_pn-${PN} = "e094e3c8f9004ca3347694bd05b99d136e8621b9"

 SRC_URI = "git://github.com/ssvb/xf86-video-fbturbo.git;protocol=http;branch=master \
           file://20-fbturbo.conf"
@ -18,9 +18,9 @@ S = "${WORKDIR}/git"

 CFLAGS += " -I${STAGING_INCDIR}/xorg "

-do_install:append() {
+do_install_append() {
    install -d ${D}${datadir}/X11/xorg.conf.d
-    install -m 0644 ${UNPACKDIR}/20-fbturbo.conf ${D}${datadir}/X11/xorg.conf.d
+    install -m 0644 ${WORKDIR}/20-fbturbo.conf ${D}${datadir}/X11/xorg.conf.d
 }

-FILES:${PN} += "${datadir}/X11/xorg.conf.d/20-fbturbo.conf"
+FILES_${PN} += "${datadir}/X11/xorg.conf.d/20-fbturbo.conf"
--- a/recipes-graphics/xorg-xserver/xserver-xf86-config_0.1.bbappend
+++ b/recipes-graphics/xorg-xserver/xserver-xf86-config_0.1.bbappend
@ -1 +1 @@
-FILESEXTRAPATHS:prepend := "${THISDIR}/${PN}:"
+FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}:"
--- a/recipes-graphics/xorg-xserver/xserver-xorg_%.bbappend
+++ b/recipes-graphics/xorg-xserver/xserver-xorg_%.bbappend
@ -1 +0,0 @@
-PACKAGECONFIG[dri3] = "-Ddri3=true,-Ddri3=false,libxshmfence"
--- a/recipes-kernel/armbian-firmware/armbian-firmware_git.bb
+++ b/recipes-kernel/armbian-firmware/armbian-firmware_git.bb
@ -1,37 +0,0 @@
-SUMMARY = "Armbian Firmware"
-DESCRIPTION = "Collection of firmware files necessary for Armbian supported hardware devices to work correctly with the Linux kernel"
-LICENSE = "CLOSED"
-
-PV = "1.0+git"
-SRC_URI = "git://github.com/armbian/firmware.git;protocol=https;branch=master"
-SRCREV = "4050e02da2dce2b74c97101f7964ecfb962f5aec"
-
-S = "${WORKDIR}/git"
-
-inherit allarch
-
-do_compile[noexec] = "1"
-
-do_install() {
-    # ap6212 (bluetooth firmware only, wifi firmware is provided by linux-firmware-bcm43430)
-    install -d "${D}${nonarch_base_libdir}/firmware/ap6212"
-    install -m 0644 "${S}/ap6212/bcm43438a1.hcd" "${D}${nonarch_base_libdir}/firmware/ap6212/"
-    install -d "${D}${nonarch_base_libdir}/firmware/brcm"
-    ln -sf ../ap6212/bcm43438a1.hcd "${D}${nonarch_base_libdir}/firmware/brcm/BCM43430A1.hcd"
-}
-
-PACKAGES =+ " \
-    ${PN}-ap6212 \
-"
-
-FILES:${PN}-ap6212 = " \
-    ${nonarch_base_libdir}/firmware/ap6212/* \
-    ${nonarch_base_libdir}/firmware/brcm/BCM43430A1.hcd \
-"
-
-
-# Make armbian-firmware depend on all of the split-out packages.
-python populate_packages:prepend () {
-    firmware_pkgs = oe.utils.packages_filter_out_system(d)
-    d.appendVar('RRECOMMENDS:armbian-firmware', ' ' + ' '.join(firmware_pkgs))
-}
--- a/recipes-kernel/linux-firmware/linux-firmware_%.bbappend
+++ b/recipes-kernel/linux-firmware/linux-firmware_%.bbappend
@ -6,21 +6,8 @@
 # WARNING: The following commit is required for NVRAM files to be included in
 # linux-firmware-bcm43430 package:
 # http://git.openembedded.org/openembedded-core/commit/?id=dde0f79f32fa6bab045ef60199903f74c4cc3393
-do_install:append:sunxi() {
+do_install_append() {
 	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.xunlong,orangepi-zero-plus2.txt
 	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.xunlong,orangepi-zero-plus2-h3.txt
 	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.friendlyarm,nanopi-neo-plus2.txt
-	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-berry.txt
-}
-
-do_install:append:cubieboard4() {
-	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.bin ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.cubietech,a80-cubieboard4.bin
-}
-
-do_install:append:merrii-a80-optimus() {
-	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.bin ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.merrii,a80-optimus.bin
-}
-
-do_install:append:sun9i() {
-	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.Prowise-PT301.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.txt
 }
--- a/recipes-kernel/linux/linux-mainline.inc
+++ b/recipes-kernel/linux/linux-mainline.inc
@ -1,14 +1,12 @@
 SECTION = "kernel"
-LICENSE = "GPL-2.0-only"
+LICENSE = "GPLv2"
 LIC_FILES_CHKSUM = "file://COPYING;md5=bbea815ee2795b2f4230826c0c6b8814"
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun9i|sun50i)"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"

 inherit kernel

 require linux.inc

-LINUX_VERSION = "${PV}"
-
 # Since we're not using git, this doesn't make a difference, but we need to fill
 # in something or kernel-yocto.bbclass will fail.
 KBRANCH ?= "master"
@ -22,34 +20,13 @@ KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"

 S = "${WORKDIR}/linux-${PV}"

-# get release version 5.x or 6.x based on version
-KRELEASE = "${@d.getVar('PV', True).split('.')[0]}"
-
-SRC_URI = "https://www.kernel.org/pub/linux/kernel/v${KRELEASE}.x/linux-${PV}.tar.xz \
-	   file://defconfig \
-	   file://sunxi-kmeta;type=kmeta;name=sunxi-kmeta;destsuffix=sunxi-kmeta \
+SRC_URI = "https://www.kernel.org/pub/linux/kernel/v5.x/linux-${PV}.tar.xz \
+	file://0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch \
+	file://0001-dts-orange-pi-zero-Add-wifi-support.patch \
+	file://defconfig \
 "

-# patches
-SRC_URI:append = " \
-	file://patches/0001-dts-orangepi-zero-Add-wifi-support.patch \
-	file://patches/0002-dts-nanopi-neo-air-Add-camera-support.patch \
-	file://patches/0003-dts-allwinner-bananapi-m2-zero-Enforce-consistent-MM.patch \
-	file://patches/0004-dts-allwinner-bananapi-m64-Consistent-nodes-for-mmc-devices.patch \
-	file://patches/0005-ARM-dts-sunxi-Add-MMC-alias-for-consistent-enumerati.patch \
-	file://patches/0006-dts-allwinner-orangepi-zero-mmc-aliases-for-consiste.patch \
-"
+SRC_URI_append_use-mailine-graphics = " file://drm.cfg"
+SRC_URI_append_bananapi = " file://axp20x.cfg"

-SRC_URI:append:use-mailine-graphics = " file://drm.cfg"
-SRC_URI:append:bananapi = " file://axp20x.cfg"
-SRC_URI:append:bananapi-m2-berry = " file://axp20x.cfg"
-SRC_URI:append:bananapi-m2-zero = " file://axp20x.cfg"
-SRC_URI:append:cubietruck = " file://axp20x.cfg"
-SRC_URI:append:nanopi-neo-air = " file://cam500b.cfg"
-SRC_URI:append:orange-pi-prime = " \
-	file://0001-dts-sun50i-h5-enable-power-button-for-orange-pi-prime.patch \
-	file://0002-dts-sun50i-h5-orange-pi-prime-add-regulator.patch \
-	file://0003-dts-sun50i-h5-orange-pi-prime-add-rtl8723cs.patch \
-"
-
-FILES_${KERNEL_PACKAGE_NAME}-base:append = " ${nonarch_base_libdir}/modules/${KERNEL_VERSION}/modules.builtin.modinfo"
+FILES_${KERNEL_PACKAGE_NAME}-base_append = " ${nonarch_base_libdir}/modules/${KERNEL_VERSION}/modules.builtin.modinfo"
--- a/recipes-kernel/linux/linux-mainline/patches/0001-dts-orangepi-zero-Add-wifi-support.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0001-dts-orangepi-zero-Add-wifi-support.patch
@ -1,20 +1,8 @@
-From a9bad790ae9a9e9befbe8e8938b6baca84ee5138 Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@open-nandra.com>
-Date: Tue, 24 Oct 2023 10:40:52 +0200
-Subject: [PATCH] dts: orangepi-zero: Add wifi support
-
-Upstream-Status: Pending
-
-Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
---
- .../allwinner/sun8i-h2-plus-orangepi-zero.dts | 46 +++++++++++++++----
- 1 file changed, 37 insertions(+), 9 deletions(-)
-
-diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
-index 3706216ff..ca94e313f 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
-+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
-@@ -80,13 +80,15 @@ status_led {
+diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+index 84cd9c061..917986cce 100644
+--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+@@ -80,13 +80,15 @@
 		};
 	};
 
@ -35,8 +23,8 @@ index 3706216ff..ca94e313f 100644
 	};
 
 	reg_vdd_cpux: vdd-cpux-regulator {
-@@ -105,10 +107,12 @@ reg_vdd_cpux: vdd-cpux-regulator {
- 		states = <1100000 0>, <1300000 1>;
+@@ -106,10 +108,12 @@
+ 			  1300000 1>;
 	};
 
 -	wifi_pwrseq: wifi_pwrseq {
@ -50,7 +38,7 @@ index 3706216ff..ca94e313f 100644
 	};
 };
 
-@@ -139,9 +143,11 @@ &mmc0 {
+@@ -140,9 +144,11 @@
 };
 
 &mmc1 {
@ -64,7 +52,7 @@ index 3706216ff..ca94e313f 100644
 	non-removable;
 	status = "okay";
 
-@@ -151,6 +157,13 @@ &mmc1 {
+@@ -152,6 +158,13 @@
 	 */
 	xr819: sdio_wifi@1 {
 		reg = <1>;
@ -78,7 +66,7 @@ index 3706216ff..ca94e313f 100644
 	};
 };
 
-@@ -207,3 +220,18 @@ &usbphy {
+@@ -208,3 +221,18 @@
 	status = "okay";
 	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 };
@ -97,6 +85,3 @@ index 3706216ff..ca94e313f 100644
 +    };
 +};
 +
-- 
-2.25.1
-
--- a/recipes-kernel/linux/linux-mainline/0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch
+++ b/recipes-kernel/linux/linux-mainline/0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch
@ -0,0 +1,80 @@
+From 4ca766a768e783ee5198f1935b7f46a5df9b4a35 Mon Sep 17 00:00:00 2001
+From: Jelle van der Waa <jelle@vdwaa.nl>
+Date: Tue, 23 Jan 2018 15:58:44 -0800
+Subject: [PATCH] ARM: dts: nanopi-neo-air: Add WiFi / eMMC
+
+Enable the WiFi (AP6212) chip and eMMC support for the NanoPi NEO Air.
+
+This patch was originally submitted by Jelle van der Waa. Martin Kelly
+modified it to compile on the latest kernel, fixed up some review
+comments from Maxime Ripard, and re-tested the patch.
+
+The patch has been reworked to add back eMMC support which has been left
+out at the last backport.
+
+Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
+Cc: linux-sunxi@googlegroups.com
+Cc: devicetree@vger.kernel.org
+Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
+Signed-off-by: Martin Kelly <mkelly@xevo.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+Signed-off-by: Florin Sarbu <florin@resin.io>
+---
+ arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 34 +++++++++++++++++++++++++++
+ 1 file changed, 34 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+index 03ff6f8..a9331fe 100644
+--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+@@ -72,6 +72,11 @@
+ 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
+ 		};
+ 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+	};
+ };
+ 
+ &mmc0 {
+@@ -84,6 +89,35 @@
+ 	status = "okay";
+ };
+ 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+ &uart0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&uart0_pins_a>;
+-- 
+2.11.0
+
--- a/recipes-kernel/linux/linux-mainline/aarch64/defconfig
+++ b/recipes-kernel/linux/linux-mainline/aarch64/defconfig
@ -339,7 +339,6 @@ CONFIG_MFD_MAX77620=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
 CONFIG_MFD_SEC_CORE=y
-CONFIG_REGULATOR=y
 CONFIG_REGULATOR_AXP20X=y
 CONFIG_REGULATOR_FAN53555=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
--- a/recipes-kernel/linux/linux-mainline/cam500b.cfg
+++ b/recipes-kernel/linux/linux-mainline/cam500b.cfg
@ -1,6 +0,0 @@
-CONFIG_MEDIA_PLATFORM_SUPPORT=y
-CONFIG_V4L_PLATFORM_DRIVERS=y
-
-CONFIG_VIDEO_OV5640=m
-CONFIG_VIDEO_SUN6I_CSI=m
-CONFIG_VIDEO_V4L2=m
--- a/recipes-kernel/linux/linux-mainline/drm.cfg
+++ b/recipes-kernel/linux/linux-mainline/drm.cfg
@ -2,7 +2,6 @@ CONFIG_DRM=y
 CONFIG_DRM_SUN4I=y
 CONFIG_DRM_SUN8I_DW_HDMI=y
 CONFIG_DRM_SUN8I_MIXER=y
-CONFIG_IOMMU_SUPPORT=y
 CONFIG_DRM_LIMA=y
 CONFIG_DRM_PANFROST=y
 CONFIG_CMA=y
--- a/recipes-kernel/linux/linux-mainline/orange-pi-prime/0001-dts-sun50i-h5-enable-power-button-for-orange-pi-prime.patch
+++ b/recipes-kernel/linux/linux-mainline/orange-pi-prime/0001-dts-sun50i-h5-enable-power-button-for-orange-pi-prime.patch
@ -1,27 +0,0 @@
-From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
-From: Gunjan Gupta <viraniac@gmail.com>
-Date: Sat, 15 Jul 2023 17:06:17 +0000
-Subject: arm64: dts: sun50i: h5: enable power button for orangepi prime
-
---
- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
-diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-index f430acd8558f..35e09098570f 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-@@ -63,8 +63,9 @@ gpio-keys {
- 
- 		key-sw4 {
- 			label = "sw4";
-			linux,code = <BTN_0>;
-+			linux,code = <KEY_POWER>;
- 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-+			wakeup-source;
- 		};
- 	};
- 
-- 
-Armbian
-
--- a/recipes-kernel/linux/linux-mainline/orange-pi-prime/0002-dts-sun50i-h5-orange-pi-prime-add-regulator.patch
+++ b/recipes-kernel/linux/linux-mainline/orange-pi-prime/0002-dts-sun50i-h5-orange-pi-prime-add-regulator.patch
@ -1,66 +0,0 @@
-From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
-From: The-going <48602507+The-going@users.noreply.github.com>
-Date: Mon, 24 Jan 2022 19:34:31 +0300
-Subject: arm64:dts: sun50i-h5-orangepi-prime add regulator
-
---
- .../allwinner/sun50i-h5-orangepi-prime.dts    | 30 +++++++++++++++++++
- 1 file changed, 30 insertions(+)
-
-diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-index 998396bc0..6dc6850c1 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-@@ -8,6 +8,7 @@
- 
- #include <dt-bindings/gpio/gpio.h>
- #include <dt-bindings/input/input.h>
-+#include <dt-bindings/pinctrl/sun4i-a10.h>
- 
- / {
- 	model = "Xunlong Orange Pi Prime";
-@@ -93,6 +94,10 @@ wifi_pwrseq: wifi_pwrseq {
- 	};
- };
- 
-+&cpu0 {
-+	cpu-supply = <&reg_vdd_cpux>;
-+};
-+
- &codec {
- 	allwinner,audio-routing =
- 		"Line Out", "LINEOUT",
-@@ -188,6 +193,31 @@ &ohci3 {
- 	status = "okay";
- };
- 
-+&r_i2c {
-+	status = "okay";
-+
-+	reg_vdd_cpux: regulator@65 {
-+		compatible = "silergy,sy8106a";
-+		reg = <0x65>;
-+		regulator-name = "vdd-cpux";
-+		silergy,fixed-microvolt = <1200000>;
-+		/*
-+		 * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
-+		 * however both the Armbian DVFS table and the official one
-+		 * have operating points with voltage under 1.1V, and both
-+		 * DVFS table are known to work properly at the lowest
-+		 * operating point.
-+		 *
-+		 * Use 1.0V as the minimum voltage instead.
-+		 */
-+		regulator-min-microvolt = <1000000>;
-+		regulator-max-microvolt = <1400000>;
-+		regulator-ramp-delay = <200>;
-+		regulator-boot-on;
-+		regulator-always-on;
-+	};
-+};
-+
- &uart0 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&uart0_pa_pins>;
-- 
-2.25.1
--- a/recipes-kernel/linux/linux-mainline/orange-pi-prime/0003-dts-sun50i-h5-orange-pi-prime-add-rtl8723cs.patch
+++ b/recipes-kernel/linux/linux-mainline/orange-pi-prime/0003-dts-sun50i-h5-orange-pi-prime-add-rtl8723cs.patch
@ -1,35 +0,0 @@
-From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
-From: The-going <48602507+The-going@users.noreply.github.com>
-Date: Mon, 7 Feb 2022 19:11:07 +0300
-Subject: arm64:dts: sun50i-h5-orangepi-prime add rtl8723cs
-
---
- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 5 +++++
- 1 file changed, 5 insertions(+)
-
-diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-index 8b92d5e77220..f430acd8558f 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
-@@ -25,6 +25,7 @@ reg_vcc3v3: vcc3v3 {
- 	aliases {
- 		ethernet0 = &emac;
- 		serial0 = &uart0;
-+		ethernet1 = &rtl8723cs;
- 	};
- 
- 	chosen {
-@@ -174,6 +175,10 @@ &mmc1 {
- 	bus-width = <4>;
- 	non-removable;
- 	status = "okay";
-+
-+	rtl8723cs: sdio_wifi@1 {
-+		reg = <1>;
-+	};
- };
- 
- &ohci0 {
-- 
-Armbian
-
--- a/recipes-kernel/linux/linux-mainline/patches/0002-dts-nanopi-neo-air-Add-camera-support.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0002-dts-nanopi-neo-air-Add-camera-support.patch
@ -1,115 +0,0 @@
-From e0d786f5465d2e2d977696cf0d02c70b78402291 Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@open-nandra.com>
-Date: Tue, 24 Oct 2023 10:42:36 +0200
-Subject: [PATCH] dts:nanopi-neo-air: Add camera support
-
-Upstream-Status: Pending
-
-Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
---
- .../dts/allwinner/sun8i-h3-nanopi-neo-air.dts | 85 +++++++++++++++++++
- 1 file changed, 85 insertions(+)
-
-diff --git a/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
-index 9e1a33f94..7a05eff33 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
-+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
-@@ -77,6 +77,39 @@ wifi_pwrseq: wifi_pwrseq {
- 		compatible = "mmc-pwrseq-simple";
- 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
- 	};
-+
-+        cam_xclk: cam-xclk {
-+                #clock-cells = <0>;
-+                compatible = "fixed-clock";
-+                clock-frequency = <24000000>;
-+                clock-output-names = "cam-xclk";
-+        };
-+
-+        reg_cam_avdd: cam-avdd {
-+                compatible = "regulator-fixed";
-+                regulator-name = "cam-avdd";
-+                regulator-min-microvolt = <2800000>;
-+                regulator-max-microvolt = <2800000>;
-+                vin-supply = <&reg_vcc3v3>;
-+        };
-+
-+        reg_cam_dovdd: cam-dovdd {
-+                compatible = "regulator-fixed";
-+                regulator-name = "cam-dovdd";
-+                regulator-min-microvolt = <1800000>;
-+                regulator-max-microvolt = <1800000>;
-+                vin-supply = <&reg_vcc3v3>;
-+        };
-+
-+        reg_cam_dvdd: cam-dvdd {
-+                compatible = "regulator-fixed";
-+                regulator-name = "cam-dvdd";
-+                regulator-min-microvolt = <1500000>;
-+                regulator-max-microvolt = <1500000>;
-+                vin-supply = <&reg_vcc3v3>;
-+        };
-+
-+
- };
- 
- &mmc0 {
-@@ -141,3 +174,55 @@ &usbphy {
- 	/* USB VBUS is always on */
- 	status = "okay";
- };
-+
-+&csi {
-+    status = "okay";
-+
-+    port {
-+        #address-cells = <1>;
-+        #size-cells = <0>;
-+
-+        /* Parallel bus endpoint */
-+        csi_from_ov5640: endpoint {
-+            remote-endpoint = <&ov5640_to_csi>;
-+            bus-width = <8>;
-+            data-shift = <2>;
-+            hsync-active = <1>; /* Active high */
-+            vsync-active = <0>; /* Active low */
-+            data-active = <1>;  /* Active high */
-+            pclk-sample = <1>;  /* Rising */
-+        };
-+    };
-+};
-+
-+&i2c2 {
-+   status = "okay";
-+
-+   ov5640: camera@3c {
-+        compatible = "ovti,ov5640";
-+        reg = <0x3c>;
-+        clocks = <&cam_xclk>;
-+        clock-names = "xclk";
-+
-+        reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>;
-+        powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>;
-+        AVDD-supply = <&reg_cam_avdd>;
-+        DOVDD-supply = <&reg_cam_dovdd>;
-+        DVDD-supply = <&reg_cam_dvdd>;
-+
-+        port {
-+            ov5640_to_csi: endpoint {
-+                remote-endpoint = <&csi_from_ov5640>;
-+                bus-width = <8>;
-+                data-shift = <2>;
-+                hsync-active = <1>; /* Active high */
-+                vsync-active = <0>; /* Active low */
-+                data-active = <1>;  /* Active high */
-+                pclk-sample = <1>;  /* Rising */
-+            };
-+        };
-+    };
-+};
-+&i2c2_pins {
-+   bias-pull-up;
-+};
-- 
-2.25.1
-
--- a/recipes-kernel/linux/linux-mainline/patches/0003-dts-allwinner-bananapi-m2-zero-Enforce-consistent-MM.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0003-dts-allwinner-bananapi-m2-zero-Enforce-consistent-MM.patch
@ -1,32 +0,0 @@
-From 7d7f32460702e99cab48909bb85ed84b67e65062 Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@open-nandra.com>
-Date: Tue, 24 Oct 2023 10:43:55 +0200
-Subject: [PATCH] dts: allwinner: bananapi-m2-zero: Enforce consistent MMC
- numbering
-
-Enforce MMC number (sometimes the order was wrong and the device does not boot).
-
-Upstream-Status: Pending
-
-Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
---
- arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts | 3 +++
- 1 file changed, 3 insertions(+)
-
-diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
-index d729b7c70..410a79487 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
-+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
-@@ -20,6 +20,9 @@ / {
- 	aliases {
- 		serial0 = &uart0;
- 		serial1 = &uart1;
-+		mmc0 = &mmc0;
-+		mmc1 = &mmc1;
-+		mmc2 = &mmc2;
- 	};
- 
- 	chosen {
-- 
-2.25.1
-
--- a/recipes-kernel/linux/linux-mainline/patches/0004-dts-allwinner-bananapi-m64-Consistent-nodes-for-mmc-devices.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0004-dts-allwinner-bananapi-m64-Consistent-nodes-for-mmc-devices.patch
@ -1,29 +0,0 @@
-From f487f62babb11d014da7a0b58a0fcdf6d217a812 Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@open-nandra.com>
-Date: Thu, 11 May 2023 11:18:33 +0200
-Subject: [PATCH] bananapi-m64: Consistent nodes for mmc devices
-
-Upstream-Status: Pending
-
-Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
---
- arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 3 +++
- 1 file changed, 3 insertions(+)
-
-diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
-index e6d5bc0f7..39a28aad8 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
-+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
-@@ -16,6 +16,9 @@ aliases {
- 		ethernet0 = &emac;
- 		serial0 = &uart0;
- 		serial1 = &uart1;
-+                mmc0 = &mmc0;
-+                mmc1 = &mmc1;
-+                mmc2 = &mmc2;
- 	};
- 
- 	chosen {
-- 
-2.25.1
-
--- a/recipes-kernel/linux/linux-mainline/patches/0005-ARM-dts-sunxi-Add-MMC-alias-for-consistent-enumerati.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0005-ARM-dts-sunxi-Add-MMC-alias-for-consistent-enumerati.patch
@ -1,31 +0,0 @@
-From 8b245b30a451bc4a4081759a6918b630ec075a7c Mon Sep 17 00:00:00 2001
-From: Stefan Gloor <code@stefan-gloor.ch>
-Date: Thu, 19 Dec 2024 10:34:54 +0100
-Subject: [PATCH] ARM: dts: sunxi: Add MMC alias for consistent enumeration
-
-Add explicit alias for MMC devices, so that (e)MMC and micro SD cards
-are enumerated consistenly. This should fix spurious boot failures when
-specifying a hard-coded root partition, e.g., mmcblk0p2.
-
-Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
-Upstream-Status: Denied https://lore.kernel.org/lkml/CAGb2v67dBhL3-AhLeHg3xOgbNZ3qu0aj9+kA+MoOMRYfr_Z_zQ@mail.gmail.com/
---
- arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts | 2 ++
- 1 file changed, 2 insertions(+)
-
-diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
-index a1b89b2a2999..9cd1eb690134 100644
--- a/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
-+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
-@@ -60,6 +60,8 @@ aliases {
- 		serial2 = &uart7;
- 		spi0 = &spi1;
- 		spi1 = &spi2;
-+		mmc0 = &mmc0;
-+		mmc1 = &mmc3;
- 	};
- 
- 	chosen {
-- 
-2.45.2
-
--- a/recipes-kernel/linux/linux-mainline/patches/0006-dts-allwinner-orangepi-zero-mmc-aliases-for-consiste.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0006-dts-allwinner-orangepi-zero-mmc-aliases-for-consiste.patch
@ -1,32 +0,0 @@
-From a2d765aab2989ba080b8f63cb0489d6a531cb3fd Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Oliver=20K=C3=A4stner?= <git@oliver-kaestner.de>
-Date: Sun, 16 Mar 2025 22:36:53 +0100
-Subject: [PATCH] dts: allwinner: orangepi-zero: mmc aliases for consistent
- enumeration
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-This fixes random boot failures.
-
-Upstream-Status: Inappropriate [https://github.com/linux-sunxi/meta-sunxi/pull/431]
-
-Signed-off-by: Oliver Kästner <git@oliver-kaestner.de>
---
- arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts | 3 +++
- 1 file changed, 3 insertions(+)
-
-diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
-index ca94e313f..570a88327 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
-+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
-@@ -59,6 +59,9 @@ aliases {
- 		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
- 		ethernet0 = &emac;
- 		ethernet1 = &xr819;
-+		mmc0 = &mmc0; /* microSD */
-+		mmc1 = &mmc1; /* XR819 WiFi */
-+		mmc2 = &mmc2;
- 	};
- 
- 	chosen {
--- a/recipes-kernel/linux/linux-mainline/sun9i/defconfig
+++ b/recipes-kernel/linux/linux-mainline/sun9i/defconfig
--- a/Show More
+++ b/Show More
				`@ -1 +0,0 @@`
				`/home/marek/data/projects/kas/sources/meta-sunxi/recipes-devtools/python/files/olinuxino-a20lime2`
				`@ -1 +0,0 @@`
				`PACKAGECONFIG:class-target = "opengl x11 gallium"`
				`@ -1 +0,0 @@`
				`PACKAGECONFIG[dri3] = "-Ddri3=true,-Ddri3=false,libxshmfence"`