Merge pull request #443 from okaestne/chore/kernel-cleanup

chore: clean up old kernel versions and fix KERNEL_DEVICETREE handling
linux-mainline: fix spacing with KERNEL_FEATURES:prepend
2025-08-28 06:43:27 +02:00 · 2025-04-05 23:04:32 +02:00 · 2025-03-31 12:31:50 +02:00 · 2025-03-31 12:31:50 +02:00 · 2025-03-31 12:21:15 +02:00 · 2025-03-30 00:56:00 +01:00
185 changed files with 234681 additions and 561 deletions
--- a/README.md
+++ b/README.md
@@ -6,6 +6,7 @@ Official sunxi OpenEmbedded layer for Allwinner-based boards.
 This layer depends on the additional layers:

 * [meta-openembedded/meta-oe](http://git.openembedded.org/meta-openembedded/tree/meta-oe)
+* [meta-arm](https://git.yoctoproject.org/meta-arm)

 Tested with core-image-base.

@@ -16,6 +17,11 @@ Maintainers:
 * Sergey Lapin <slapin@ossfans.org>
 * Marek Belisko <marek.belisko@gmail.com>

+Community
+===========
+
+You can reach community + ask your question on gitter: https://matrix.to/#/#meta-sunxi:gitter.im
+
 Kernel / U-Boot Version
 ===========
 Most Allwinner devices and hardware are supported in mainline kernel and U-Boot, so this layer builds mainline by default.
--- a/classes/sdcard_image-sunxi.bbclass
+++ b/classes/sdcard_image-sunxi.bbclass
@@ -1,124 +0,0 @@
-inherit image_types
-
-#
-# Create an image that can by written onto a SD card using dd.
-# Originally written for rasberrypi adapt for the needs of allwinner sunxi based boards
-#
-# The disk layout used is:
-#
-#    0                      -> 8*1024                           - reserverd
-#    8*1024                 ->                                  - arm combined spl/u-boot or aarch64 spl
-#    40*1024                ->                                  - aarch64 u-boot
-#    2048*1024              -> BOOT_SPACE                       - bootloader and kernel
-#
-#
-
-# This image depends on the rootfs image
-IMAGE_TYPEDEP_sunxi-sdimg = "${SDIMG_ROOTFS_TYPE}"
-
-# Boot partition volume id
-BOOTDD_VOLUME_ID ?= "boot"
-
-# Boot partition size [in KiB]
-BOOT_SPACE ?= "40960"
-
-# First partition begin at sector 2048 : 2048*1024 = 2097152
-IMAGE_ROOTFS_ALIGNMENT = "2048"
-
-# Use an uncompressed ext4 by default as rootfs
-SDIMG_ROOTFS_TYPE ?= "ext4"
-SDIMG_ROOTFS = "${IMGDEPLOYDIR}/${IMAGE_NAME}.rootfs.${SDIMG_ROOTFS_TYPE}"
-
-do_image_sunxi_sdimg[depends] += " \
-			parted-native:do_populate_sysroot \
-			mtools-native:do_populate_sysroot \
-			dosfstools-native:do_populate_sysroot \
-			virtual/kernel:do_deploy \
-			virtual/bootloader:do_deploy \
-			"
-
-# SD card image name
-SDIMG = "${IMGDEPLOYDIR}/${IMAGE_NAME}.rootfs.sunxi-sdimg"
-
-IMAGE_CMD_sunxi-sdimg () {
-
-	# Align partitions
-	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE} + ${IMAGE_ROOTFS_ALIGNMENT} - 1)
-	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE_ALIGNED} - ${BOOT_SPACE_ALIGNED} % ${IMAGE_ROOTFS_ALIGNMENT})
-	SDIMG_SIZE=$(expr ${IMAGE_ROOTFS_ALIGNMENT} + ${BOOT_SPACE_ALIGNED} + $ROOTFS_SIZE + ${IMAGE_ROOTFS_ALIGNMENT})
-
-	# Initialize sdcard image file
-	dd if=/dev/zero of=${SDIMG} bs=1 count=0 seek=$(expr 1024 \* ${SDIMG_SIZE})
-
-	# Create partition table
-	parted -s ${SDIMG} mklabel msdos
-	# Create boot partition and mark it as bootable
-	parted -s ${SDIMG} unit KiB mkpart primary fat32 ${IMAGE_ROOTFS_ALIGNMENT} $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT})
-	parted -s ${SDIMG} set 1 boot on
-	# Create rootfs partition
-	parted -s ${SDIMG} unit KiB mkpart primary ext2 $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT}) $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT} \+ ${ROOTFS_SIZE})
-	parted ${SDIMG} print
-
-	# Create a vfat image with boot files
-	BOOT_BLOCKS=$(LC_ALL=C parted -s ${SDIMG} unit b print | awk '/ 1 / { print substr($4, 1, length($4 -1)) / 512 /2 }')
-	rm -f ${WORKDIR}/boot.img
-	mkfs.vfat -n "${BOOTDD_VOLUME_ID}" -S 512 -C ${WORKDIR}/boot.img $BOOT_BLOCKS
-
-	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin ::${KERNEL_IMAGETYPE}
-
-	# Copy device tree file
-	if test -n "${KERNEL_DEVICETREE}"; then
-		for DTS_FILE in ${KERNEL_DEVICETREE}; do
-			DTS_BASE_NAME=`basename ${DTS_FILE} | awk -F "." '{print $1}'`
-			DTS_DIR_NAME=`dirname ${DTS_FILE}`
-			if [ -e ${DEPLOY_DIR_IMAGE}/"${DTS_BASE_NAME}.dtb" ]; then
-
-				if [ ${DTS_FILE} != ${DTS_BASE_NAME}.dtb ]; then
-					mmd -i ${WORKDIR}/boot.img ::/${DTS_DIR_NAME}
-				fi
-
-				kernel_bin="`readlink ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${MACHINE}.bin`"
-				kernel_bin_for_dtb="`readlink ${DEPLOY_DIR_IMAGE}/${DTS_BASE_NAME}.dtb | sed "s,$DTS_BASE_NAME,${KERNEL_IMAGETYPE},g;s,\.dtb$,.bin,g"`"
-				if [ $kernel_bin = $kernel_bin_for_dtb ]; then
-					mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${DTS_BASE_NAME}.dtb ::/${DTS_FILE}
-				fi
-			fi
-		done
-	fi
-
-	if [ -e "${DEPLOY_DIR_IMAGE}/fex.bin" ]
-	then
-		mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/fex.bin ::script.bin
-	fi
-	if [ -e "${DEPLOY_DIR_IMAGE}/boot.scr" ]
-	then
-		mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/boot.scr ::boot.scr
-	fi
-
-
-	# Add stamp file
-	echo "${IMAGE_NAME}" > ${WORKDIR}/image-version-info
-	mcopy -i ${WORKDIR}/boot.img -v ${WORKDIR}/image-version-info ::
-
-	# Burn Partitions
-	dd if=${WORKDIR}/boot.img of=${SDIMG} conv=notrunc seek=1 bs=$(expr ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
-	# If SDIMG_ROOTFS_TYPE is a .xz file use xzcat
-	if echo "${SDIMG_ROOTFS_TYPE}" | egrep -q "*\.xz"
-	then
-		xzcat ${SDIMG_ROOTFS} | dd of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
-	else
-		dd if=${SDIMG_ROOTFS} of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
-	fi
-
-	# write u-boot-spl at the begining of sdcard in one shot
-	SPL_FILE=$(basename ${SPL_BINARY})
-	dd if=${DEPLOY_DIR_IMAGE}/${SPL_FILE} of=${SDIMG} bs=1024 seek=8 conv=notrunc
-}
-
-# write uboot.itb for arm64 boards
-IMAGE_CMD_sunxi-sdimg_append_sun50i () {
-	if [ -e "${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY}" ]
-	then
-		dd if=${DEPLOY_DIR_IMAGE}/${UBOOT_BINARY} of=${SDIMG} bs=1024 seek=40 conv=notrunc
-	fi
-}
--- a/conf/layer.conf
+++ b/conf/layer.conf
@@ -4,14 +4,14 @@ BBPATH .= ":${LAYERDIR}"
 # We have a recipes directory, add to BBFILES
 BBFILES += "${LAYERDIR}/recipes*/*/*.bb ${LAYERDIR}/recipes*/*/*.bbappend"

-BBFILE_COLLECTIONS += "meta-sunxi"
-BBFILE_PATTERN_meta-sunxi := "^${LAYERDIR}/"
-BBFILE_PRIORITY_meta-sunxi = "10"
+BBFILE_COLLECTIONS += "sunxi"
+BBFILE_PATTERN_sunxi := "^${LAYERDIR}/"
+BBFILE_PRIORITY_sunxi = "10"

 # This should only be incremented on significant changes that will
 # cause compatibility issues with other layers
-LAYERVERSION_meta-sunxi = "1"
+LAYERVERSION_sunxi = "1"

-LAYERDEPENDS_meta-sunxi = "core openembedded-layer"
+LAYERDEPENDS_sunxi = "core meta-python meta-arm"

-LAYERSERIES_COMPAT_meta-sunxi = "zeus dunfell"
+LAYERSERIES_COMPAT_sunxi = "styhead"
--- a/conf/machine/bananapi-m2-berry.conf
+++ b/conf/machine/bananapi-m2-berry.conf
@@ -0,0 +1,9 @@
+#@TYPE: Machine
+#@NAME: bananapi-m2-berry
+#@DESCRIPTION: Machine configuration for the Banana Pi M2 Berry, based on Allwinner V40 CPU
+
+require conf/machine/include/sun8i.inc
+require conf/machine/include/hardware/ap6212a.inc
+
+KERNEL_DEVICETREE = "allwinner/sun8i-v40-bananapi-m2-berry.dtb"
+UBOOT_MACHINE = "bananapi_m2_berry_defconfig"
--- a/conf/machine/bananapi-m2-zero.conf
+++ b/conf/machine/bananapi-m2-zero.conf
@@ -0,0 +1,9 @@
+#@TYPE: Machine
+#@NAME: bananapi-m2-zero
+#@DESCRIPTION: Machine configuration for the Banana Pi M2 Zero, base on Allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+require conf/machine/include/hardware/ap6212a.inc
+
+KERNEL_DEVICETREE = "allwinner/sun8i-h2-plus-bananapi-m2-zero.dtb"
+UBOOT_MACHINE = "bananapi_m2_zero_defconfig"
--- a/conf/machine/bananapi-m2m.conf
+++ b/conf/machine/bananapi-m2m.conf
@@ -4,6 +4,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-r16-bananapi-m2m.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-r16-bananapi-m2m.dtb"
 UBOOT_MACHINE = "Bananapi_m2m_defconfig"
-
--- a/conf/machine/bananapi-m2plus.conf
+++ b/conf/machine/bananapi-m2plus.conf
@@ -4,6 +4,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h3-bananapi-m2-plus.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-bananapi-m2-plus.dtb"
 UBOOT_MACHINE = "bananapi_m2_plus_h3_defconfig"
-
--- a/conf/machine/bananapi.conf
+++ b/conf/machine/bananapi.conf
@@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-bananapi.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-bananapi.dtb"
 UBOOT_MACHINE = "Bananapi_config"
-SUNXI_FEX_FILE = "sys_config/a20/Bananapi.fex"
+SUNXI_FEX_FILE = "sys_config/a20/Bananapi.fex"
--- a/conf/machine/cubieboard.conf
+++ b/conf/machine/cubieboard.conf
@@ -4,6 +4,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "sun4i-a10-cubieboard.dtb"
+KERNEL_DEVICETREE = "allwinner/sun4i-a10-cubieboard.dtb"
 UBOOT_MACHINE = "Cubieboard_config"
 SUNXI_FEX_FILE = "sys_config/a10/cubieboard.fex"
--- a/conf/machine/cubieboard2.conf
+++ b/conf/machine/cubieboard2.conf
@@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-cubieboard2.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-cubieboard2.dtb"
 UBOOT_MACHINE = "Cubieboard2_config"
 SUNXI_FEX_FILE = "sys_config/a20/cubieboard2.fex"
--- a/conf/machine/cubieboard4.conf
+++ b/conf/machine/cubieboard4.conf
@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: CubieBoard4
+#@DESCRIPTION: Machine configuration for the cubieboard4, based on allwinner A80 CPU http://cubieboard.org/
+
+require conf/machine/include/sun9i.inc
+require conf/machine/include/hardware/ap6330.inc
+
+KERNEL_IMAGETYPE = "zImage"
+
+KERNEL_DEVICETREE = "allwinner/sun9i-a80-cubieboard4.dtb"
+UBOOT_MACHINE = "Cubieboard4_defconfig"
--- a/conf/machine/cubietruck.conf
+++ b/conf/machine/cubietruck.conf
@@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-cubietruck.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-cubietruck.dtb"
 UBOOT_MACHINE = "Cubietruck_config"
-SUNXI_FEX_FILE = "sys_config/a20/cubietruck.fex"
+SUNXI_FEX_FILE = "sys_config/a20/cubietruck.fex"
--- a/conf/machine/include/hardware/ap6212a.inc
+++ b/conf/machine/include/hardware/ap6212a.inc
@@ -1,5 +1,9 @@
 # Include for boards with AMPAK 6212A Wifi / Bluetooth module
 # https://linux-sunxi.org/Wifi#Ampak

-MACHINE_EXTRA_RRECOMMENDS_append = " kernel-module-brcmfmac"
-MACHINE_EXTRA_RDEPENDS_append = " linux-firmware-bcm43430"
+MACHINE_EXTRA_RRECOMMENDS:append = " kernel-module-brcmfmac kernel-module-hci-uart"
+MACHINE_EXTRA_RDEPENDS:append = " linux-firmware-bcm43430 armbian-firmware-ap6212"
+
+MACHINE_FEATURES:append = " bluetooth wifi"
+
+KERNEL_FEATURES:append = " features/ap6212/ap6212.scc"
--- a/conf/machine/include/hardware/ap6330.inc
+++ b/conf/machine/include/hardware/ap6330.inc
@@ -0,0 +1,7 @@
+# Include for boards with AMPAK AP6330 Wifi / Bluetooth module
+# https://linux-sunxi.org/Wifi#Ampak
+
+MACHINE_EXTRA_RRECOMMENDS:append = " kernel-module-brcmfmac"
+MACHINE_EXTRA_RDEPENDS:append = " linux-firmware-bcm4330"
+
+MACHINE_FEATURES:append = " bluetooth wifi"
--- a/conf/machine/include/sun4i.inc
+++ b/conf/machine/include/sun4i.inc
@@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/tune-cortexa8.inc
+require conf/machine/include/arm/armv7a/tune-cortexa8.inc

 SOC_FAMILY = "sun4i"
--- a/conf/machine/include/sun50i-h6.inc
+++ b/conf/machine/include/sun50i-h6.inc
@@ -0,0 +1,8 @@
+require conf/machine/include/sunxi64.inc
+
+DEFAULTTUNE ?= "cortexa53-crypto"
+require conf/machine/include/arm/armv8a/tune-cortexa53.inc
+
+MACHINEOVERRIDES =. "sun50i:"
+
+SOC_FAMILY = "sun50i-h6"
--- a/conf/machine/include/sun50i-h616.inc
+++ b/conf/machine/include/sun50i-h616.inc
@@ -0,0 +1,8 @@
+require conf/machine/include/sunxi64.inc
+
+DEFAULTTUNE ?= "cortexa53-crypto"
+require conf/machine/include/arm/armv8a/tune-cortexa53.inc
+
+MACHINEOVERRIDES =. "sun50i:"
+
+SOC_FAMILY = "sun50i-h616"
--- a/conf/machine/include/sun50i.inc
+++ b/conf/machine/include/sun50i.inc
@@ -1,6 +1,6 @@
 require conf/machine/include/sunxi64.inc

 DEFAULTTUNE ?= "cortexa53-crypto"
-require conf/machine/include/tune-cortexa53.inc
+require conf/machine/include/arm/armv8a/tune-cortexa53.inc

 SOC_FAMILY = "sun50i"
--- a/conf/machine/include/sun5i.inc
+++ b/conf/machine/include/sun5i.inc
@@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/tune-cortexa8.inc
+require conf/machine/include/arm/armv7a/tune-cortexa8.inc

 SOC_FAMILY = "sun5i"
--- a/conf/machine/include/sun7i.inc
+++ b/conf/machine/include/sun7i.inc
@@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/tune-cortexa7.inc
+require conf/machine/include/arm/armv7a/tune-cortexa7.inc

 SOC_FAMILY = "sun7i"
--- a/conf/machine/include/sun8i.inc
+++ b/conf/machine/include/sun8i.inc
@@ -1,5 +1,5 @@
 require conf/machine/include/sunxi.inc
 require conf/machine/include/sunxi-mali.inc
-require conf/machine/include/tune-cortexa7.inc
+require conf/machine/include/arm/armv7a/tune-cortexa7.inc

 SOC_FAMILY = "sun8i"
--- a/conf/machine/include/sun9i.inc
+++ b/conf/machine/include/sun9i.inc
@@ -0,0 +1,5 @@
+require conf/machine/include/sunxi.inc
+require conf/machine/include/sunxi-mali.inc
+require conf/machine/include/arm/armv7a/tune-cortexa15.inc
+
+SOC_FAMILY = "sun9i"
--- a/conf/machine/include/sunxi-mali-driver.inc
+++ b/conf/machine/include/sunxi-mali-driver.inc
@@ -4,7 +4,7 @@ PREFERRED_PROVIDER_virtual/libgles1 ?= "sunxi-mali"
 PREFERRED_PROVIDER_virtual/libgles2 ?= "sunxi-mali"
 PREFERRED_PROVIDER_virtual/egl ?= "sunxi-mali"

-PACKAGECONFIG_remove_pn-xserver-xorg = "${@bb.utils.contains('DISTRO_FEATURES', 'x11', 'glamor', '', d)}"
+PACKAGECONFIG:remove:pn-xserver-xorg = "${@bb.utils.contains('DISTRO_FEATURES', 'x11', 'glamor', '', d)}"

 XSERVER += "sunxi-mali \
            sunxi-mali-dev"
--- a/conf/machine/include/sunxi.inc
+++ b/conf/machine/include/sunxi.inc
@@ -1,26 +1,26 @@
 SOC_FAMILY ??= ""
 include conf/machine/include/soc-family.inc

+MACHINEOVERRIDES =. "sunxi:"
+
 # Sub-architecture support
 MACHINE_SOCARCH_SUFFIX ?= ""
 MACHINE_SOCARCH_SUFFIX_sun4i = "-sun4i"

 PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
 XSERVER = "xserver-xorg \
-           xf86-video-fbturbo \
           xf86-input-evdev \
           xf86-input-mouse \
           xf86-input-keyboard"

 PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
-PREFERRED_VERSION_linux-mainline ?= "5.4.%"
+PREFERRED_VERSION_linux-mainline ?= "6.6.%"
 PREFERRED_PROVIDER_u-boot ?= "u-boot"
 PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"

 KERNEL_IMAGETYPE ?= "uImage"

-IMAGE_CLASSES += "sdcard_image-sunxi"
-IMAGE_FSTYPES += "ext3 tar.gz sunxi-sdimg"
+IMAGE_FSTYPES += "ext3 tar.gz wic.gz wic.bmap"

 MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"

@@ -30,5 +30,18 @@ UBOOT_ENTRYPOINT ?= "0x40008000"

 SPL_BINARY ?= "u-boot-sunxi-with-spl.bin"

-SERIAL_CONSOLE ?= "115200 ttyS0"
+SERIAL_CONSOLES ?= "115200;ttyS0"
 MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"
+
+# Mimic the sdcard_image-sunxi.bbclass
+# image-version-info file was also generated and installed to boot partition,
+# but it is missing here - can be added somehow (how?) if required
+SUNXI_FEX_FILE ?= " "
+SUNXI_BOOT_SPACE ?= "40"
+IMAGE_BOOT_FILES ?= "${KERNEL_IMAGETYPE} boot.scr"
+# ship fex file for sunxi kernel, devicetree file for mainline kernel
+IMAGE_BOOT_FILES += "${@bb.utils.contains('PREFERRED_PROVIDER_virtual/kernel', 'linux-sunxi', '${SUNXI_FEX_FILE}', d.getVar('KERNEL_DEVICETREE', '').split('/')[-1], d)}"
+WKS_FILES ?= "sunxi-sdcard-image.wks.in"
+WKS_FILE_DEPENDS ?= "virtual/kernel u-boot"
+# in case of sunxi kernel, sunxi-board-fex must be built prior wic image assembly
+WKS_FILE_DEPENDS += " ${@bb.utils.contains('PREFERRED_PROVIDER_virtual/kernel', 'linux-sunxi', 'sunxi-board-fex', '', d)}"
--- a/conf/machine/include/sunxi64.inc
+++ b/conf/machine/include/sunxi64.inc
@@ -1,24 +1,32 @@
 SOC_FAMILY ??= ""
 include conf/machine/include/soc-family.inc

+MACHINEOVERRIDES =. "sunxi:sunxi64:"
+
 PREFERRED_PROVIDER_virtual/kernel ?= "linux-mainline"
+PREFERRED_VERSION_linux-mainline ?= "6.6.%"
 PREFERRED_PROVIDER_u-boot ?= "u-boot"
 PREFERRED_PROVIDER_virtual/bootloader ?= "u-boot"

 KERNEL_IMAGETYPE ?= "Image"

-IMAGE_CLASSES += "sdcard_image-sunxi"
-IMAGE_FSTYPES += "ext4 tar.gz sunxi-sdimg"
+IMAGE_FSTYPES += "ext4 tar.gz wic.gz wic.bmap"

 MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"

 UBOOT_LOCALVERSION = "-g${@d.getVar('SRCPV', True).partition('+')[2][0:7]}"

 UBOOT_ENTRYPOINT ?= "0x40008000"
-UBOOT_LOADADDRESS ?= "0x400080OB00"
+UBOOT_LOADADDRESS ?= "0x40008000"

-UBOOT_BINARY ?= "u-boot.itb"
-SPL_BINARY ?= "spl/sunxi-spl.bin"
+#UBOOT_BINARY ?= "u-boot.itb"
+SPL_BINARY ?= "u-boot-sunxi-with-spl.bin"

-SERIAL_CONSOLE ?= "115200 ttyS0"
+SERIAL_CONSOLES ?= "115200;ttyS0"
 MACHINE_FEATURES ?= "alsa apm keyboard rtc serial screen usbgadget usbhost vfat"
+
+SUNXI_BOOT_SPACE ?= "40"
+IMAGE_BOOT_FILES ?= "${KERNEL_IMAGETYPE} boot.scr ${@d.getVar('KERNEL_DEVICETREE', '').split('/')[-1]}"
+
+WKS_FILES ?= "sunxi-sdcard-image.wks.in"
+WKS_FILE_DEPENDS ?= "virtual/kernel u-boot"
--- a/conf/machine/lamobo-r1.conf
+++ b/conf/machine/lamobo-r1.conf
@@ -0,0 +1,10 @@
+#@TYPE: Machine
+#@NAME: Lamobo R1
+#@DESCRIPTION: Machine configuration for the lamobo r1, based on allwinner A20 CPU http://bananapi.org/
+
+require conf/machine/include/sun7i.inc
+
+MACHINE_EXTRA_RRECOMMENDS = " kernel-modules kernel-devicetree"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-lamobo-r1.dtb"
+UBOOT_MACHINE = "Lamobo_R1_config"
+SUNXI_FEX_FILE = "sys_config/a20/lamobo-r1.fex"
--- a/conf/machine/licheepi-zero.conf
+++ b/conf/machine/licheepi-zero.conf
@@ -0,0 +1,9 @@
+#@TYPE: Machine
+#@NAME: licheepi-zero
+#@DESCRIPTION: Machine configuration for the licheepi-zero, based on allwinner V3s CPU
+
+require conf/machine/include/sun8i.inc
+
+
+UBOOT_MACHINE = "LicheePi_Zero_defconfig"
+KERNEL_DEVICETREE = "allwinner/sun8i-v3s-licheepi-zero.dtb"
--- a/conf/machine/mangopi-mq-t-t113.conf
+++ b/conf/machine/mangopi-mq-t-t113.conf
@@ -0,0 +1,10 @@
+#@TYPE: Machine
+#@NAME: MangoPi MQ-R T113-S3
+#@DESCRIPTION: Machine configuration for the MangoPi MQ-R, based on the Allwinner T113-S3 CPU
+
+require conf/machine/include/sun8i.inc
+
+KERNEL_DEVICETREE = "allwinner/sun8i-t113s-mangopi-mq-r-t113.dtb"
+KERNEL_IMAGETYPE = "zImage"
+
+UBOOT_MACHINE = "mangopi_mq_r_defconfig"
--- a/conf/machine/marsboard-a10.conf
+++ b/conf/machine/marsboard-a10.conf
@@ -0,0 +1,10 @@
+#@TYPE: Machine
+#@NAME: HAOYU Electronics MarsBoard A10
+#@DESCRIPTION: Machine configuration for the HAOYU Electronics MarsBoard A10, based on Allwinner A10 CPU
+#https://linux-sunxi.org/MarsBoard_A10
+
+require conf/machine/include/sun4i.inc
+
+KERNEL_DEVICETREE = "allwinner/sun4i-a10-marsboard.dtb"
+UBOOT_MACHINE = "Marsboard_A10_config"
+SUNXI_FEX_FILE = "sys_config/a10/marsboard_a10.fex"
--- a/conf/machine/mele.conf
+++ b/conf/machine/mele.conf
@@ -4,6 +4,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "sun4i-a10-a1000.dtb"
+KERNEL_DEVICETREE = "allwinner/sun4i-a10-a1000.dtb"
 UBOOT_MACHINE = "Mele_A1000_config"
-SUNXI_FEX_FILE = "sys_config/a10/mele_a1000.fex"
+SUNXI_FEX_FILE = "sys_config/a10/mele_a1000.fex"
--- a/conf/machine/merrii-a80-optimus.conf
+++ b/conf/machine/merrii-a80-optimus.conf
@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: Merrii A80 Optimus
+#@DESCRIPTION: Machine configuration for the Merrii A80 Optimus, based on Allwinner A80 CPU https://linux-sunxi.org/Merrii_A80_Optimus_Board
+
+require conf/machine/include/sun9i.inc
+require conf/machine/include/hardware/ap6330.inc
+
+KERNEL_IMAGETYPE = "zImage"
+
+KERNEL_DEVICETREE = "allwinner/sun9i-a80-optimus.dtb"
+UBOOT_MACHINE = "Merrii_A80_Optimus_defconfig"
--- a/conf/machine/nanopi-m1-plus.conf
+++ b/conf/machine/nanopi-m1-plus.conf
@@ -4,6 +4,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h3-nanopi-m1-plus.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-m1-plus.dtb"
 UBOOT_MACHINE = "nanopi_m1_plus_defconfig"
-
--- a/conf/machine/nanopi-m1.conf
+++ b/conf/machine/nanopi-m1.conf
@@ -0,0 +1,8 @@
+#@TYPE: Machine
+#@NAME: NanoPi M1
+#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi Neo, based on #the Allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-m1.dtb"
+UBOOT_MACHINE = "nanopi_m1_defconfig"
--- a/conf/machine/nanopi-neo-air.conf
+++ b/conf/machine/nanopi-neo-air.conf
@@ -5,5 +5,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo-air.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-neo-air.dtb"
 UBOOT_MACHINE = "nanopi_neo_air_defconfig"
--- a/conf/machine/nanopi-neo.conf
+++ b/conf/machine/nanopi-neo.conf
@@ -4,6 +4,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h3-nanopi-neo.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-neo.dtb"
 UBOOT_MACHINE = "nanopi_neo_defconfig"
-
--- a/conf/machine/nanopi-r1.conf
+++ b/conf/machine/nanopi-r1.conf
@@ -0,0 +1,8 @@
+#@TYPE: Machine
+#@NAME: NanoPi R1
+#@DESCRIPTION: Machine configuration for the FriendlyARM NanoPi R1, based on #the Allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-nanopi-r1.dtb"
+UBOOT_MACHINE = "nanopi_r1_defconfig"
--- a/conf/machine/olinuxino-a10lime.conf
+++ b/conf/machine/olinuxino-a10lime.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "sun4i-a10-olinuxino-lime.dtb"
+KERNEL_DEVICETREE = "allwinner/sun4i-a10-olinuxino-lime.dtb"
 UBOOT_MACHINE = "A10-OLinuXino-Lime_config"
-SUNXI_FEX_FILE = "sys_config/a10/a10-olinuxino-lime.fex"
+SUNXI_FEX_FILE = "sys_config/a10/a10-olinuxino-lime.fex"
--- a/conf/machine/olinuxino-a10s.conf
+++ b/conf/machine/olinuxino-a10s.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun5i.inc

-KERNEL_DEVICETREE = "sun5i-a10s-olinuxino-micro.dtb"
+KERNEL_DEVICETREE = "allwinner/sun5i-a10s-olinuxino-micro.dtb"
 UBOOT_MACHINE = "A10s-OLinuXino-M_config"
-SUNXI_FEX_FILE = "sys_config/a10s/a10s-olinuxino-m.fex"
+SUNXI_FEX_FILE = "sys_config/a10s/a10s-olinuxino-m.fex"
--- a/conf/machine/olinuxino-a13.conf
+++ b/conf/machine/olinuxino-a13.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun5i.inc

-KERNEL_DEVICETREE = "sun5i-a13-olinuxino.dtb"
+KERNEL_DEVICETREE = "allwinner/sun5i-a13-olinuxino.dtb"
 UBOOT_MACHINE = "A13-OLinuXino_config"
-SUNXI_FEX_FILE = "sys_config/a13/a13-olinuxino.fex"
+SUNXI_FEX_FILE = "sys_config/a13/a13-olinuxino.fex"
--- a/conf/machine/olinuxino-a20.conf
+++ b/conf/machine/olinuxino-a20.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-olinuxino-micro.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-micro.dtb"
 UBOOT_MACHINE = "A20-OLinuXino_MICRO_config"
-SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_micro.fex"
+SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_micro.fex"
--- a/conf/machine/olinuxino-a20lime.conf
+++ b/conf/machine/olinuxino-a20lime.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-lime.dtb"
 UBOOT_MACHINE = "A20-OLinuXino-Lime_config"
-SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime.fex"
+SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime.fex"
--- a/conf/machine/olinuxino-a20lime2-emmc.conf
+++ b/conf/machine/olinuxino-a20lime2-emmc.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime2-emmc.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-lime2-emmc.dtb"
 UBOOT_MACHINE = "A20-OLinuXino-Lime2-eMMC_config"
 SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime2.fex"
--- a/conf/machine/olinuxino-a20lime2.conf
+++ b/conf/machine/olinuxino-a20lime2.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-olinuxino-lime2.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-olinuxino-lime2.dtb"
 UBOOT_MACHINE = "A20-OLinuXino-Lime2_config"
 SUNXI_FEX_FILE = "sys_config/a20/a20-olinuxino_lime2.fex"
--- a/conf/machine/olinuxino-a20som.conf
+++ b/conf/machine/olinuxino-a20som.conf
@@ -5,6 +5,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-olimex-som-evb.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-olimex-som-evb.dtb"
 UBOOT_MACHINE = "A20-Olimex-SOM-EVB_config"
 SUNXI_FEX_FILE = "sys_config/a20/olimex_a20_som.fex"
--- a/conf/machine/orange-pi-3lts.conf
+++ b/conf/machine/orange-pi-3lts.conf
@@ -0,0 +1,28 @@
+#@TYPE: Machine
+#@NAME: orange-pi-3lts
+#@DESCRIPTION: Machine configuration for the Orange Pi 3 LTS , based on Allwinner H6 CPU
+# Note: Some boards have faulty RTC a fix is included by default
+# a workarround in the dts ins include by default but in can removed adding
+# KERNEL_FEATURES:remove = " bsp/orange-pi-3lts/fix-rtc.scc" to local.conf
+
+require conf/machine/include/sun50i-h6.inc
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h6-orangepi-3-lts.dtb"
+UBOOT_MACHINE = "orangepi_3_lts_defconfig"
+
+SPL_BINARY = "u-boot-sunxi-with-spl.bin"
+
+# as for now neither graphics nor audio is supported
+MACHINE_FEATURES:remove = " x11 alsa rtc"
+MACHINE_FEATURES:append = " bluetooth wifi"
+
+# fiwrware needed for wifi + bt
+MACHINE_EXTRA_RRECOMMENDS += " uwe5622-firmware"
+
+# Load modules for wifi & bt
+# Note: fo wifi a custom hci attach userspace sofware is needed that is not included in the layer
+KERNEL_MODULE_AUTOLOAD += " sprdwl_ng sprdbt_tty "
+
+
+
+
--- a/conf/machine/orange-pi-lite.conf
+++ b/conf/machine/orange-pi-lite.conf
@@ -0,0 +1,8 @@
+#@TYPE: Machine
+#@NAME: orange-pi-lite
+#@DESCRIPTION: Machine configuration for the orange-pi-lite, based on Allwinner H3 CPU
+
+require conf/machine/include/sun8i.inc
+
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-lite.dtb"
+UBOOT_MACHINE = "orangepi_lite_defconfig"
--- a/conf/machine/orange-pi-one-plus.conf
+++ b/conf/machine/orange-pi-one-plus.conf
@@ -0,0 +1,9 @@
+#@TYPE: Machine
+#@NAME: orange-pi-one-plus
+#@DESCRIPTION: Machine configuration for the Orange Pi One Plus, based on Allwinner H6 CPU
+
+
+require conf/machine/include/sun50i-h6.inc
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h6-orangepi-one-plus.dtb"
+UBOOT_MACHINE = "orangepi_one_plus_defconfig"
--- a/conf/machine/orange-pi-one.conf
+++ b/conf/machine/orange-pi-one.conf
@@ -4,6 +4,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h3-orangepi-one.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-one.dtb"
 UBOOT_MACHINE = "orangepi_one_defconfig"
-
--- a/conf/machine/orange-pi-pc-plus.conf
+++ b/conf/machine/orange-pi-pc-plus.conf
@@ -4,6 +4,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc-plus.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-pc-plus.dtb"
 UBOOT_MACHINE = "orangepi_pc_plus_defconfig"
-
--- a/conf/machine/orange-pi-pc.conf
+++ b/conf/machine/orange-pi-pc.conf
@@ -4,6 +4,5 @@

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h3-orangepi-pc.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-pc.dtb"
 UBOOT_MACHINE = "orangepi_pc_defconfig"
-
--- a/conf/machine/orange-pi-pc2.conf
+++ b/conf/machine/orange-pi-pc2.conf
@@ -0,0 +1,8 @@
+#@TYPE: Machine
+#@NAME: orangepi-pc2
+#@DESCRIPTION: Machine configuration for the orangepi-pc2, based on Allwinner A64 CPU
+
+require conf/machine/include/sun50i.inc
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h5-orangepi-pc2.dtb"
+UBOOT_MACHINE = "orangepi_pc2_defconfig"
--- a/conf/machine/orange-pi-plus2e.conf
+++ b/conf/machine/orange-pi-plus2e.conf
@@ -1,8 +0,0 @@
-#@TYPE: Machine
-#@NAME: orange-pi-plus2e
-#@DESCRIPTION: Machine configuration for the orange-pi-plus2e, base on allwinner H3 CPU
-
-require conf/machine/include/sun8i.inc
-
-KERNEL_DEVICETREE = "sun8i-h3-orangepi-plus2e.dtb"
-UBOOT_MACHINE = "orangepi_plus2e_defconfig"
--- a/conf/machine/orange-pi-prime.conf
+++ b/conf/machine/orange-pi-prime.conf
@@ -0,0 +1,11 @@
+#@TYPE: Machine
+#@NAME: orange-pi-prime
+#@DESCRIPTION: Machine configuration for the orange-pi-prime, base on Allwinner H5 CPU
+
+require conf/machine/include/sun50i.inc
+require conf/machine/include/hardware/ap6212a.inc
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h5-orangepi-prime.dtb"
+UBOOT_MACHINE = "orangepi_prime_defconfig"
+
+MACHINE_EXTRA_RRECOMMENDS:append = " linux-firmware-rtl8723"
--- a/conf/machine/orange-pi-r1.conf
+++ b/conf/machine/orange-pi-r1.conf
@@ -0,0 +1,8 @@
+#@TYPE: Machine
+#@NAME: orange-pi-r1
+#@DESCRIPTION: Machine configuration for the orange-pi-r1, base on allwinner H2+ CPU
+
+require conf/machine/include/sun8i.inc
+
+KERNEL_DEVICETREE = "allwinner/sun8i-h2-plus-orangepi-r1.dtb"
+UBOOT_MACHINE = "orangepi_r1_defconfig"
--- a/conf/machine/orange-pi-zero-plus2-h3.conf
+++ b/conf/machine/orange-pi-zero-plus2-h3.conf
@@ -5,5 +5,5 @@
 require conf/machine/include/sun8i.inc
 require conf/machine/include/hardware/ap6212a.inc

-KERNEL_DEVICETREE = "sun8i-h3-orangepi-zero-plus2.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h3-orangepi-zero-plus2.dtb"
 UBOOT_MACHINE = "orangepi_zero_plus2_h3_defconfig"
--- a/conf/machine/orange-pi-zero.conf
+++ b/conf/machine/orange-pi-zero.conf
@@ -1,9 +1,8 @@
 #@TYPE: Machine
-#@NAME: orange-pi-one
-#@DESCRIPTION: Machine configuration for the orange-pi-one, base on allwinner H3 CPU
+#@NAME: orange-pi-zero
+#@DESCRIPTION: Machine configuration for the orange-pi-zero, based on Allwinner H2 CPU

 require conf/machine/include/sun8i.inc

-KERNEL_DEVICETREE = "sun8i-h2-plus-orangepi-zero.dtb"
+KERNEL_DEVICETREE = "allwinner/sun8i-h2-plus-orangepi-zero.dtb"
 UBOOT_MACHINE = "orangepi_zero_defconfig"
-
--- a/conf/machine/orange-pi-zero2.conf
+++ b/conf/machine/orange-pi-zero2.conf
@@ -0,0 +1,21 @@
+#@TYPE: Machine
+#@NAME: orange-pi-zero-2
+#@DESCRIPTION: Machine configuration for the orange-pi-zero-2, based on Allwinner H616 CPU
+
+require conf/machine/include/sun50i-h616.inc
+
+KERNEL_DEVICETREE = "allwinner/sun50i-h616-orangepi-zero2.dtb"
+UBOOT_MACHINE = "orangepi_zero2_defconfig"
+
+SPL_BINARY = "u-boot-sunxi-with-spl.bin"
+
+# as for now neither graphics nor audio is supported
+MACHINE_FEATURES:remove = "alsa x11"
+MACHINE_FEATURES:append = "bluetooth wifi"
+
+MACHINE_EXTRA_RRECOMMENDS = "uwe5622-firmware"
+
+# Load modules for wifi & bt
+# Note: fo wifi a custom hci attach userspace sofware is needed that is not included in the layer
+KERNEL_MODULE_AUTOLOAD += " sprdwl_ng sprdbt_tty "
+
--- a/conf/machine/pcduino.conf
+++ b/conf/machine/pcduino.conf
@@ -4,6 +4,6 @@

 require conf/machine/include/sun4i.inc

-KERNEL_DEVICETREE = "sun4i-a10-pcduino.dtb"
+KERNEL_DEVICETREE = "allwinner/sun4i-a10-pcduino.dtb"
 UBOOT_MACHINE = "Linksprite_pcDuino_defconfig"
 SUNXI_FEX_FILE = "sys_config/a10/pcduino.fex"
--- a/conf/machine/pcduino3.conf
+++ b/conf/machine/pcduino3.conf
@@ -4,6 +4,6 @@

 require conf/machine/include/sun7i.inc

-KERNEL_DEVICETREE = "sun7i-a20-pcduino3.dtb"
+KERNEL_DEVICETREE = "allwinner/sun7i-a20-pcduino3.dtb"
 UBOOT_MACHINE = "Linksprite_pcDuino3_defconfig"
-SUNXI_FEX_FILE = "sys_config/a20/linksprite_pcduino3.fex"
+SUNXI_FEX_FILE = "sys_config/a20/linksprite_pcduino3.fex"
--- a/recipes-bsp/atf/atf-sunxi_git.bb
+++ b/recipes-bsp/atf/atf-sunxi_git.bb
@@ -1,27 +0,0 @@
-DESCRIPTION = "ARM Trusted Firmware Allwinner"
-LICENSE = "BSD"
-LIC_FILES_CHKSUM = "file://license.md;md5=829bdeb34c1d9044f393d5a16c068371"
-
-SRC_URI = "git://github.com/apritzel/arm-trusted-firmware;nobranch=1"
-SRCREV = "aa75c8da415158a94b82a430b2b40000778e851f"
-
-S = "${WORKDIR}/git"
-B = "${WORKDIR}/build"
-
-COMPATIBLE_MACHINE = "(sun50i)"
-
-PLATFORM_sun50i = "sun50iw1p1"
-
-LDFLAGS[unexport] = "1"
-
-do_compile() {
-    oe_runmake -C ${S} BUILD_BASE=${B} \
-      CROSS_COMPILE=${TARGET_PREFIX} \
-      PLAT=${PLATFORM} \
-      bl31 \
-      all
-}
-
-do_install() {
-    install -D -p -m 0644 ${B}/${PLATFORM}/release/bl31.bin ${DEPLOY_DIR_IMAGE}/bl31.bin
-}
--- a/recipes-bsp/sunxi-board-fex/sunxi-board-fex.bb
+++ b/recipes-bsp/sunxi-board-fex/sunxi-board-fex.bb
@@ -9,9 +9,9 @@ PR = "r0"

 COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i)"

-SRC_URI = "git://github.com/linux-sunxi/sunxi-boards.git;protocol=git"
+SRC_URI = "git://github.com/linux-sunxi/sunxi-boards.git;protocol=https;branch=master"
 # Increase PV with SRCREV change
-SRCREV = "496ef0fbd166cc2395daa76dd3c359357420963d"
+SRCREV = "af5f938ea14a3614d35ad3d9ab51a5d392117444"

 S = "${WORKDIR}/git"

--- a/recipes-bsp/trusted-firmware-a/trusted-firmware-a_%.bbappend
+++ b/recipes-bsp/trusted-firmware-a/trusted-firmware-a_%.bbappend
@@ -0,0 +1,7 @@
+COMPATIBLE_MACHINE:sunxi = "(sun50i|sun50i-h616|sun50i-h6)"
+
+TFA_PLATFORM:sun50i = "sun50i_a64"
+TFA_PLATFORM:sun50i-h6 = "sun50i_h6"
+TFA_PLATFORM:sun50i-h616 = "sun50i_h616"
+
+TFA_BUILD_TARGET:sunxi = "bl31"
--- a/recipes-bsp/u-boot/files/0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch
+++ b/recipes-bsp/u-boot/files/0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch
@@ -1,9 +1,9 @@
-From 6adb2ebdc4022c24497e9ee4dccab41d18e3105d Mon Sep 17 00:00:00 2001
+From 6a64d90ca4d976c16a2e102dbad0848e4d29776c Mon Sep 17 00:00:00 2001
 From: Florin Sarbu <florin@resin.io>
 Date: Wed, 12 Sep 2018 14:22:49 +0200
 Subject: [PATCH] nanopi_neo_air_defconfig: Enable eMMC support

-Upstream-status: Pending
+Upstream-Status: Pending
 Signed-off-by: Florin Sarbu <florin@resin.io>

 ---
@@ -11,11 +11,11 @@ Signed-off-by: Florin Sarbu <florin@resin.io>
 1 file changed, 1 insertion(+)

 diff --git a/configs/nanopi_neo_air_defconfig b/configs/nanopi_neo_air_defconfig
-index 5ad90ddd16..8b7a4eb45d 100644
+index 806d95c1cc..8899cc3a15 100644
 --- a/configs/nanopi_neo_air_defconfig
 +++ b/configs/nanopi_neo_air_defconfig
-@@ -15,3 +15,4 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-neo-air"
+@@ -9,3 +9,4 @@ CONFIG_DRAM_CLK=408
+ CONFIG_CONSOLE_MUX=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
- CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
 +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
--- a/recipes-bsp/u-boot/files/0001-sunxi-board-Fix-early-PMIC-setup-conditions.patch
+++ b/recipes-bsp/u-boot/files/0001-sunxi-board-Fix-early-PMIC-setup-conditions.patch
@@ -0,0 +1,41 @@
+From f4dde09fa41eb538b743ee2104c1e2e10cc7e13f Mon Sep 17 00:00:00 2001
+From: Leon Anavi <leon.anavi@konsulko.com>
+Date: Sat, 14 Dec 2024 10:59:09 +0000
+Subject: [PATCH] sunxi: board: Fix early PMIC setup conditions
+
+Patch provided by Andre Przywara through the U-Boot mailing list:
+https://lists.denx.de/pipermail/u-boot/2024-December/575050.html
+
+Upstream-Status: Pending
+
+Suggested-by: Andre Przywara <andre.przywara@arm.com>
+Signed-off-by: Leon Anavi <leon.anavi@konsulko.com>
+---
+ board/sunxi/board.c | 4 +++-
+ 1 file changed, 3 insertions(+), 1 deletion(-)
+
+diff --git a/board/sunxi/board.c b/board/sunxi/board.c
+index 961cdcde74..d6759fe853 100644
+--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
+@@ -577,7 +577,6 @@ void sunxi_board_init(void)
+ 
+ #ifdef CONFIG_AXP_DCDC1_VOLT
+ 	power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
+-	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
+ #endif
+ #ifdef CONFIG_AXP_DCDC2_VOLT
+ 	power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
+@@ -586,6 +585,9 @@ void sunxi_board_init(void)
+ #ifdef CONFIG_AXP_DCDC4_VOLT
+ 	power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
+ #endif
+#ifdef CONFIG_AXP_DCDC5_VOLT
+	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
+#endif
+ 
+ #ifdef CONFIG_AXP_ALDO1_VOLT
+ 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
+-- 
+2.47.1
+
--- a/recipes-bsp/u-boot/files/0002-Added-nanopi-r1-board-support.patch
+++ b/recipes-bsp/u-boot/files/0002-Added-nanopi-r1-board-support.patch
@@ -0,0 +1,42 @@
+From 767a05572ef5b93c2e157749b1754cbe261ee43d Mon Sep 17 00:00:00 2001
+From: Marek Belisko <marek.belisko@open-nandra.com>
+Date: Fri, 8 Apr 2022 11:33:53 +0200
+Subject: [PATCH] Added nanopi-r1 board support
+
+Patch taken from : https://github.com/armbian/build/blob/master/patch/u-boot/u-boot-sunxi/add-nanopi-r1-and-duo2.patch
+
+Upstream-Status: Pending
+
+Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
+---
+diff --git a/configs/nanopi_r1_defconfig b/configs/nanopi_r1_defconfig
+new file mode 100644
+index 0000000..e028b41
+--- /dev/null
+++ b/configs/nanopi_r1_defconfig
+@@ -0,0 +1,22 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MACPWR="PD6"
+# CONFIG_VIDEO_DE2 is not set
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_CONSOLE_MUX=y
+CONFIG_SYS_CLK_FREQ=480000000
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-r1"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+-- 
+2.7.4
+
--- a/recipes-bsp/u-boot/files/0002-Revert-sunxi-psci-avoid-error-address-of-packed-memb.patch
+++ b/recipes-bsp/u-boot/files/0002-Revert-sunxi-psci-avoid-error-address-of-packed-memb.patch
@@ -1,67 +0,0 @@
-From bb6f500c10cc8f5f31245626899e0732b7b287c5 Mon Sep 17 00:00:00 2001
-From: Marek Belisko <marek.belisko@open-nandra.com>
-Date: Wed, 19 Aug 2020 13:39:49 +0200
-Subject: [PATCH] Revert "sunxi: psci: avoid error address-of-packed-member"
-
-This reverts commit 9bd34a69a453d409792e08c00953ce8862145e65.
---
- arch/arm/cpu/armv7/sunxi/psci.c | 16 +++++-----------
- 1 file changed, 5 insertions(+), 11 deletions(-)
-
-diff --git a/arch/arm/cpu/armv7/sunxi/psci.c b/arch/arm/cpu/armv7/sunxi/psci.c
-index 5b68900..2c5d99e 100644
--- a/arch/arm/cpu/armv7/sunxi/psci.c
-+++ b/arch/arm/cpu/armv7/sunxi/psci.c
-@@ -75,7 +75,7 @@ static void __secure __mdelay(u32 ms)
- 	isb();
- }
- 
-static void __secure clamp_release(void __maybe_unused *clamp)
-+static void __secure clamp_release(u32 __maybe_unused *clamp)
- {
- #if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN7I) || \
- 	defined(CONFIG_MACH_SUN8I_H3) || \
-@@ -90,7 +90,7 @@ static void __secure clamp_release(void __maybe_unused *clamp)
- #endif
- }
- 
-static void __secure clamp_set(void __maybe_unused *clamp)
-+static void __secure clamp_set(u32 __maybe_unused *clamp)
- {
- #if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN7I) || \
- 	defined(CONFIG_MACH_SUN8I_H3) || \
-@@ -99,28 +99,22 @@ static void __secure clamp_set(void __maybe_unused *clamp)
- #endif
- }
- 
-static void __secure sunxi_power_switch(void *clamp, void *pwroff_ptr, bool on,
-+static void __secure sunxi_power_switch(u32 *clamp, u32 *pwroff, bool on,
- 					int cpu)
- {
-	u32 pwroff;
-
-	memcpy(&pwroff, pwroff_ptr, sizeof(u32));
-
- 	if (on) {
- 		/* Release power clamp */
- 		clamp_release(clamp);
- 
- 		/* Clear power gating */
-		clrbits_le32(&pwroff, BIT(cpu));
-+		clrbits_le32(pwroff, BIT(cpu));
- 	} else {
- 		/* Set power gating */
-		setbits_le32(&pwroff, BIT(cpu));
-+		setbits_le32(pwroff, BIT(cpu));
- 
- 		/* Activate power clamp */
- 		clamp_set(clamp);
- 	}
-
-	memcpy(pwroff_ptr, &pwroff, sizeof(u32));
- }
- 
- #ifdef CONFIG_MACH_SUN8I_R40
-- 
-2.7.4
-
--- a/recipes-bsp/u-boot/files/0003-sunxi-H6-Enable-Ethernet-on-Orange-Pi-One-Plus.patch
+++ b/recipes-bsp/u-boot/files/0003-sunxi-H6-Enable-Ethernet-on-Orange-Pi-One-Plus.patch
@@ -0,0 +1,58 @@
+From: Anne Macedo <retpolanne@posteo.net>
+Date: Tue, 11 Jul 2023 00:39:58 +0000
+Subject: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus
+
+Enable Ethernet on Orange Pi One Plus by using the correct phy for
+Realtek RTL8211E instead of the Generic One. Also use CONFIG_MACPWR to
+turn on ethernet on startup.
+
+After this patch is applied, a few issues can be seen:
+
+- there's still a PHY reset timed out error that doesn't seem to cause
+  any impacts to the overall connection
+
+- sometimes the emac driver times out after reset (yellow LED turns on
+  and never blinks)
+
+For future patches: for now, CONFIG_MACPWR is the only way to enable
+Ethernet on boot. There's already code on the dts for using the 3v3-gmac
+regulator. However, it is not probed on boot, so it only starts after a
+"regulator status" command is issued.
+
+More details about the troubleshooting on [1].
+
+Upstream-Status: Submitted
+
+[1] https://lore.kernel.org/u-boot/4wsvwgy56e2xfgtvioru2tf2ofkqprlts36qggivxogww6pn5j@4jk63zxhzhag/
+
+Signed-off-by: Anne Macedo <retpolanne@posteo.net>
+---
+ arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 2 +-
+ configs/orangepi_one_plus_defconfig          | 4 ++++
+ 2 files changed, 5 insertions(+), 1 deletion(-)
+
+diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
+index 29a081e72a..6427c58f8a 100644
+--- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
+++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
+@@ -37,7 +37,7 @@
+ 
+ &mdio {
+ 	ext_rgmii_phy: ethernet-phy@1 {
+-		compatible = "ethernet-phy-ieee802.3-c22";
+		compatible = "ethernet-phy-id001c.c915", "ethernet-phy-ieee802.3-c22" ;
+ 		reg = <1>;
+ 	};
+ };
+diff --git a/configs/orangepi_one_plus_defconfig b/configs/orangepi_one_plus_defconfig
+index aa5f540eb1..a1835492db 100644
+--- a/configs/orangepi_one_plus_defconfig
+++ b/configs/orangepi_one_plus_defconfig
+@@ -8,3 +8,7 @@ CONFIG_SUNXI_DRAM_H6_LPDDR3=y
+ # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+ CONFIG_USB_EHCI_HCD=y
+ CONFIG_USB_OHCI_HCD=y
+CONFIG_SUN8I_EMAC=y
+CONFIG_PHY_REALTEK=y
+CONFIG_PHY_ETHERNET_ID=y
+CONFIG_MACPWR="PD6"
--- a/recipes-bsp/u-boot/files/0004-OrangePi-3-LTS-support.patch
+++ b/recipes-bsp/u-boot/files/0004-OrangePi-3-LTS-support.patch
@@ -0,0 +1,421 @@
+From 9966dda20246285abf8b417bd251d5a4bea3e423 Mon Sep 17 00:00:00 2001
+From: Juliano Dorigão <jdorigao@gmail.com>
+Date: Fri, 3 Mar 2023 16:11:30 -0400
+Subject: [PATCH] OrangePi 3 LTS support
+
+Upstream-Status: Pending
+---
+ arch/arm/dts/Makefile                     |   1 +
+ arch/arm/dts/sun50i-h6-orangepi-3-lts.dts | 361 ++++++++++++++++++++++
+ configs/orangepi_3_lts_defconfig          |  19 ++
+ 3 files changed, 381 insertions(+)
+ create mode 100644 arch/arm/dts/sun50i-h6-orangepi-3-lts.dts
+ create mode 100644 configs/orangepi_3_lts_defconfig
+
+diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
+index 43951a77..8dbbb6f4 100644
+--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
+@@ -710,6 +710,7 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
+ dtb-$(CONFIG_MACH_SUN50I_H6) += \
+ 	sun50i-h6-beelink-gs1.dtb \
+ 	sun50i-h6-orangepi-3.dtb \
+	sun50i-h6-orangepi-3-lts.dtb \
+ 	sun50i-h6-orangepi-lite2.dtb \
+ 	sun50i-h6-orangepi-one-plus.dtb \
+ 	sun50i-h6-pine-h64.dtb \
+diff --git a/arch/arm/dts/sun50i-h6-orangepi-3-lts.dts b/arch/arm/dts/sun50i-h6-orangepi-3-lts.dts
+new file mode 100644
+index 00000000..67f38b8a
+--- /dev/null
+++ b/arch/arm/dts/sun50i-h6-orangepi-3-lts.dts
+@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2023 Jernej Skrabec <jernej.skrabec@gmail.com>
+// Based on sun50i-h6-orangepi-3.dts, which is:
+// Copyright (C) 2019 Ondřej Jirman <megous@megous.com>
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+#include "sun50i-h6-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "OrangePi 3 LTS";
+	compatible = "xunlong,orangepi-3-lts", "allwinner,sun50i-h6";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	ext_osc32k: ext_osc32k_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "ext_osc32k";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "orangepi:red:power";
+			gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+		};
+
+		led-1 {
+			label = "orangepi:green:status";
+			gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
+			default-state = "on";
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC jack */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <150000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
+	};
+
+	reg_vcc33_wifi: vcc33-wifi {
+		/* Always on 3.3V regulator for WiFi and BT */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc33-wifi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+	};
+
+	reg_vcc_wifi_io: vcc-wifi-io {
+		/* Always on 1.8V/300mA regulator for WiFi and BT IO */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-wifi-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&reg_vcc33_wifi>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdca>;
+};
+
+&de {
+	status = "okay";
+};
+
+&dwc3 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_gmac_3v3>;
+	allwinner,rx-delay-ps = <1500>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&reg_dcdcc>;
+	status = "okay";
+};
+
+&hdmi {
+	hvcc-supply = <&reg_bldo2>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+
+		reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
+		reset-assert-us = <15000>;
+		reset-deassert-us = <40000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_cldo1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc33_wifi>;
+	vqmmc-supply = <&reg_vcc_wifi_io>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_cldo1>;
+	vqmmc-supply = <&reg_bldo2>;
+	cap-mmc-hw-reset;
+	non-removable;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pc-supply = <&reg_bldo2>;
+	vcc-pd-supply = <&reg_cldo1>;
+	vcc-pg-supply = <&reg_bldo3>;
+};
+
+&r_ir {
+	status = "okay";
+};
+
+&r_rsb {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	axp805: pmic@745 {
+		compatible = "x-powers,axp805", "x-powers,axp806";
+		reg = <0x745>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-pl-led-ir";
+			};
+
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc33-audio-tv-ephy-mac";
+			};
+
+			/* ALDO3 is shorted to CLDO1 */
+			reg_aldo3: aldo3 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc33-io-pd-emmc-sd-usb-uart-1";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18-dram-bias-pll";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-efuse-pcie-hdmi-pc";
+			};
+
+			reg_bldo3: bldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc-pm-pg-dcxoio-wifi";
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			reg_cldo1: cldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc33-io-pd-emmc-sd-usb-uart-2";
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1160000>;
+				regulator-ramp-delay = <2500>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-enable-ramp-delay = <32000>;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-ramp-delay = <2500>;
+				regulator-name = "vdd-gpu";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <980000>;
+				regulator-max-microvolt = <980000>;
+				regulator-name = "vdd-sys";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vcc-dram";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&pwm {
+	status = "okay";
+};
+
+&r_ir {
+	status = "okay";
+};
+
+&rtc {
+	clocks = <&ext_osc32k>;
+};
+
+/delete-node/ &spi0;
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usb2otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb2phy {
+	usb0_id_det-gpios = <&pio 2 15 GPIO_ACTIVE_HIGH>; /* PC15 */
+	usb0_vbus-supply = <&reg_vcc5v>;
+	usb3_vbus-supply = <&reg_vcc5v>;
+	status = "okay";
+};
+
+&usb3phy {
+	status = "okay";
+};
+diff --git a/configs/orangepi_3_lts_defconfig b/configs/orangepi_3_lts_defconfig
+new file mode 100644
+index 00000000..41a9af4e
+--- /dev/null
+++ b/configs/orangepi_3_lts_defconfig
+@@ -0,0 +1,19 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-orangepi-3-lts"
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I_H6=y
+CONFIG_SUNXI_DRAM_H6_LPDDR3=y
+CONFIG_MMC0_CD_PIN="PF6"
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL_STACK=0x118000
+CONFIG_SYS_PBSIZE=1024
+CONFIG_SYS_BOOTM_LEN=0x2000000
+CONFIG_PHY_SUN50I_USB3=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+-- 
+2.39.2
+
--- a/recipes-bsp/u-boot/files/0004-mangopi-mq-r-t113-Fix-serial-console.patch
+++ b/recipes-bsp/u-boot/files/0004-mangopi-mq-r-t113-Fix-serial-console.patch
@@ -0,0 +1,30 @@
+From bf813915bf480154c707e0be14016cef94adbd95 Mon Sep 17 00:00:00 2001
+From: Marek Belisko <marek.belisko@gmail.com>
+Date: Tue, 7 May 2024 11:27:08 +0200
+Subject: [PATCH] mangopi-mq-r-t113: Fix serial console
+
+Serial console is on uart3 not on uart0.
+
+Upstream-Status: Inappropriate (for this board only)
+
+Signed-off-by: Marek Belisko <marek.belisko@gmail.com>
+---
+ include/configs/sunxi-common.h | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
+index b8ca77d031..4e4808d2c1 100644
+--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
+@@ -324,7 +324,7 @@
+ 	MEM_LAYOUT_ENV_EXTRA_SETTINGS \
+ 	DFU_ALT_INFO_RAM \
+ 	"fdtfile=" FDTFILE "\0" \
+-	"console=ttyS0,115200\0" \
+	"console=ttyS3,115200\0" \
+ 	"uuid_gpt_esp=" UUID_GPT_ESP "\0" \
+ 	"uuid_gpt_system=" UUID_GPT_SYSTEM "\0" \
+ 	"partitions=" PARTS_DEFAULT "\0" \
+-- 
+2.25.1
+
--- a/recipes-bsp/u-boot/files/arm/boot.cmd
+++ b/recipes-bsp/u-boot/files/arm/boot.cmd
@@ -6,6 +6,6 @@ if itest.b *0x28 == 0x02 ; then
 	rootdev=mmcblk1p2
 fi
 setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
-load mmc 0:1 ${fdt_addr_r} ${fdtfile} || load mmc 0:1 ${fdt_addr_r} boot/${fdtfile}
+load mmc 0:1 ${fdt_addr_r} ${fdtfile} || load mmc 0:1 ${fdt_addr_r} boot/allwinner/${fdtfile}
 load mmc 0:1 ${kernel_addr_r} zImage || load mmc 0:1 ${kernel_addr_r} boot/zImage || load mmc 0:1 ${kernel_addr_r} uImage || load mmc 0:1 ${kernel_addr_r} boot/uImage
 bootz ${kernel_addr_r} - ${fdt_addr_r} || bootm ${kernel_addr_r} - ${fdt_addr_r}
--- a/recipes-bsp/u-boot/files/bananapi-m64/boot.cmd
+++ b/recipes-bsp/u-boot/files/bananapi-m64/boot.cmd
@@ -0,0 +1,11 @@
+# Default to (primary) SD
+rootdev=mmcblk0p2
+if itest.b *0x28 == 0x02 ; then
+	# U-Boot loaded from eMMC or secondary SD so use it for rootfs too
+	echo "U-boot loaded from eMMC or secondary SD"
+	rootdev=mmcblk2p2
+fi
+setenv bootargs console=${console} console=tty1 root=/dev/${rootdev} rootwait panic=10 ${extra}
+load mmc 0:1 ${fdt_addr_r} ${fdtfile}
+load mmc 0:1 ${kernel_addr_r} Image
+booti ${kernel_addr_r} - ${fdt_addr_r}
--- a/recipes-bsp/u-boot/u-boot-sunxi.bb
+++ b/recipes-bsp/u-boot/u-boot-sunxi.bb
@@ -2,7 +2,7 @@ DESCRIPTION = "U-Boot port for sunxi"

 require recipes-bsp/u-boot/u-boot.inc

-LICENSE = "GPLv2"
+LICENSE = "GPL-2.0-only"
 LIC_FILES_CHKSUM = "file://Licenses/gpl-2.0.txt;md5=b234ee4d69f5fce4486a80fdaf4a4263"

 # No patches for other machines yet
@@ -19,7 +19,7 @@ UBOOT_MACHINE_olinuxino-a10s = "A10s-OLinuXino-Micro_config"
 UBOOT_MACHINE_meleg = "Mele_A1000G_config"

 SRC_URI = " \
-	git://github.com/linux-sunxi/u-boot-sunxi.git;protocol=git;branch=sunxi \
+	git://github.com/linux-sunxi/u-boot-sunxi.git;protocol=https;branch=sunxi \
 	file://0001-gcc5-fixes.patch \
 	file://0002-gcc6-fixes.patch \
 	file://0003-No-gcc-version-specific-includes.patch \
--- a/recipes-bsp/u-boot/u-boot_%.bbappend
+++ b/recipes-bsp/u-boot/u-boot_%.bbappend
@@ -1,33 +1,39 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/files:"
+FILESEXTRAPATHS:prepend:sunxi := "${THISDIR}/files:"

-DEPENDS += " bc-native dtc-native swig-native python3-native flex-native bison-native "
-DEPENDS_append_sun50i = " atf-sunxi "
+DEPENDS:append:sunxi = " bc-native dtc-native swig-native python3-native flex-native bison-native "
+DEPENDS:append:sun50i = " trusted-firmware-a"

-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
+COMPATIBLE_MACHINE:sunxi = "(sun4i|sun5i|sun7i|sun8i|sun9i|sun50i)"

-DEFAULT_PREFERENCE_sun4i="1"
-DEFAULT_PREFERENCE_sun5i="1"
-DEFAULT_PREFERENCE_sun7i="1"
-DEFAULT_PREFERENCE_sun8i="1"
-DEFAULT_PREFERENCE_sun50i="1"
+DEFAULT_PREFERENCE:sun4i = "1"
+DEFAULT_PREFERENCE:sun5i = "1"
+DEFAULT_PREFERENCE:sun7i = "1"
+DEFAULT_PREFERENCE:sun8i = "1"
+DEFAULT_PREFERENCE:sun50i = "1"

-SRC_URI += " \
-           file://0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch \
-           file://boot.cmd \
-           "
-# fix booting issue on orange pi zero
-SRC_URI_append_orange-pi-zero = " file://0002-Revert-sunxi-psci-avoid-error-address-of-packed-memb.patch"
+SRC_URI:append:sunxi = " \
+    file://0001-nanopi_neo_air_defconfig-Enable-eMMC-support.patch \
+    file://0002-Added-nanopi-r1-board-support.patch \
+    file://0003-sunxi-H6-Enable-Ethernet-on-Orange-Pi-One-Plus.patch \
+    file://0004-OrangePi-3-LTS-support.patch \
+    file://boot.cmd \
+"
+SRC_URI:append:sun9i = " \
+    file://0001-sunxi-board-Fix-early-PMIC-setup-conditions.patch \
+"

-SRC_URI_append_nanopi-neo = " file://0002-Revert-sunxi-psci-avoid-error-address-of-packed-memb.patch"
+SRC_URI:append:mangopi-mq-t-t113 = " \
+    file://0004-mangopi-mq-r-t113-Fix-serial-console.patch \
+    "

-UBOOT_ENV_SUFFIX = "scr"
-UBOOT_ENV = "boot"
+UBOOT_ENV_SUFFIX:sunxi = "scr"
+UBOOT_ENV:sunxi = "boot"

-EXTRA_OEMAKE += ' HOSTLDSHARED="${BUILD_CC} -shared ${BUILD_LDFLAGS} ${BUILD_CFLAGS}" '
-EXTRA_OEMAKE_append_sun50i = " BL31=${DEPLOY_DIR_IMAGE}/bl31.bin "
+EXTRA_OEMAKE:append:sunxi = ' HOSTLDSHARED="${BUILD_CC} -shared ${BUILD_LDFLAGS} ${BUILD_CFLAGS}" '
+EXTRA_OEMAKE:append:sun50i = " BL31=${DEPLOY_DIR_IMAGE}/bl31.bin SCP=/dev/null"

-do_compile_sun50i[depends] += "atf-sunxi:do_deploy"
+do_compile:sun50i[depends] += "trusted-firmware-a:do_deploy"

-do_compile_append() {
-    ${B}/tools/mkimage -C none -A arm -T script -d ${WORKDIR}/boot.cmd ${WORKDIR}/${UBOOT_ENV_BINARY}
+do_compile:append:sunxi() {
+    ${B}/tools/mkimage -C none -A arm -T script -d ${UNPACKDIR}/boot.cmd ${UNPACKDIR}/${UBOOT_ENV_BINARY}
 }
--- a/recipes-devtools/python/files/olinuxino-a20lime2-emmc
+++ b/recipes-devtools/python/files/olinuxino-a20lime2-emmc
@@ -0,0 +1 @@
+/home/marek/data/projects/kas/sources/meta-sunxi/recipes-devtools/python/files/olinuxino-a20lime2
--- a/recipes-devtools/python/pya20_0.2.12.bb
+++ b/recipes-devtools/python/pya20_0.2.12.bb
@@ -1,7 +1,7 @@
 DESCRIPTION = "A module to control Allwinner GPIO,SPI and I2C channels"
 HOMEPAGE = "https://pypi.python.org/pypi/pyA20"
 SECTION = "devel/python"
-LICENSE = "GPLv3"
+LICENSE = "GPL-3.0-only"
 LIC_FILES_CHKSUM = "file://PKG-INFO;md5=4e584373bb0f46ef1e423cb7df37847d"
 DEPENDS = "python3"

@@ -13,10 +13,10 @@ SRC_URI = "https://pypi.python.org/packages/source/p/pyA20/pyA20-${PV}.tar.gz \
          "
 S = "${WORKDIR}/pyA20-${PV}"

-inherit distutils3
+inherit setuptools3

-do_compile_prepend() { 
-cp ${WORKDIR}/mapping.h ${S}/pyA20/gpio/mapping.h
+do_compile:prepend() { 
+    cp ${UNPACKDIR}/mapping.h ${S}/pyA20/gpio/mapping.h
 }

 SRC_URI[md5sum] = "cab03b4931199804603d1074f6d8f48f"
--- a/recipes-graphics/libgles/sunxi-mali_git.bb
+++ b/recipes-graphics/libgles/sunxi-mali_git.bb
@@ -21,8 +21,8 @@ python __anonymous() {
        raise bb.parse.SkipPackage("%s-%s ONLY supports hardfp mode for now" % (pkgn, pkgv))
 }

-SRCREV_pn-${PN} = "d343311efc8db166d8371b28494f0f27b6a58724"
-SRC_URI = "gitsm://github.com/linux-sunxi/sunxi-mali.git \
+SRCREV = "d343311efc8db166d8371b28494f0f27b6a58724"
+SRC_URI = "git://github.com/linux-sunxi/sunxi-mali.git;protocol=https;branch=master \
           file://0001-Add-EGLSyncKHR-EGLTimeKHR-and-GLChar-definition.patch \
           file://0002-Add-missing-GLchar-definition.patch \
           file://0003-Fix-sed-to-replace-by-the-correct-var.patch \
@@ -92,13 +92,13 @@ do_install() {
 # Packages like xf86-video-fbturbo dlopen() libUMP.so, so we do need to ship the .so files in ${PN}
 PACKAGES =+ "${PN}-test"

-RPROVIDES_${PN} += "libGLESv2.so libEGL.so libGLESv2.so libGLESv1_CM.so libMali.so"
-RDEPENDS_${PN}-test = "${PN}"
+RPROVIDES:${PN} += "libGLESv2.so libEGL.so libGLESv2.so libGLESv1_CM.so libMali.so"
+RDEPENDS:${PN}-test = "${PN}"

-FILES_${PN} += "${libdir}/lib*.so"
-FILES_${PN}-dev = "${includedir} ${libdir}/pkgconfig/*"
-FILES_${PN}-test = "${bindir}/sunximali-test"
+FILES:${PN} += "${libdir}/lib*.so"
+FILES:${PN}-dev = "${includedir} ${libdir}/pkgconfig/*"
+FILES:${PN}-test = "${bindir}/sunximali-test"

 # These are closed binaries generated elsewhere so don't check ldflags & text relocations
-INSANE_SKIP_${PN} = "dev-so ldflags textrel"
-INSANE_SKIP_${PN}-test = "dev-so ldflags textrel"
+INSANE_SKIP:${PN} = "dev-so ldflags textrel"
+INSANE_SKIP:${PN}-test = "dev-so ldflags textrel"
--- a/recipes-graphics/libump/libump_git.bb
+++ b/recipes-graphics/libump/libump_git.bb
@@ -1,14 +1,14 @@
 DESCRIPTION = "Unified Memory Provider userspace API source code needed for xf86-video-mali compilation"

-LICENSE = "Apache-2"
+LICENSE = "Apache-2.0"
 LIC_FILES_CHKSUM = "file://debian/copyright;md5=edf7fb6071cae7ec80d537a05ee17198"

 inherit autotools

 PV = "r4p0-00rel0+git${SRCPV}"
-SRCREV_pn-${PN} = "ec0680628744f30b8fac35e41a7bd8e23e59c39f"
+SRCREV = "ec0680628744f30b8fac35e41a7bd8e23e59c39f"

-SRC_URI = "git://github.com/linux-sunxi/libump.git"
+SRC_URI = "git://github.com/linux-sunxi/libump.git;protocol=https;branch=master"

 S = "${WORKDIR}/git"

--- a/recipes-graphics/mesa/mesa-gl.bbappend
+++ b/recipes-graphics/mesa/mesa-gl.bbappend
@@ -0,0 +1 @@
+PACKAGECONFIG:class-target = "opengl x11 gallium"
--- a/recipes-graphics/mesa/mesa_%.bbappend
+++ b/recipes-graphics/mesa/mesa_%.bbappend
@@ -1,5 +1,5 @@
 # Enable lima and panfrost Mesa drivers
-PACKAGECONFIG_append_use-mailine-graphics = " lima panfrost"
+PACKAGECONFIG:append:use-mailine-graphics = " lima panfrost"
 # Enable KMS renderonly Mesa support
 # See https://cgit.freedesktop.org/mesa/mesa/commit/?id=2b780fe89300199f2334539aa1678e9b68f0434f
-GALLIUMDRIVERS_append_use-mailine-graphics = ",kmsro"
+GALLIUMDRIVERS:append:use-mailine-graphics = ",kmsro"
--- a/recipes-graphics/tslib/tslib_1.1.bbappend.disabled
+++ b/recipes-graphics/tslib/tslib_1.1.bbappend.disabled
@@ -1,4 +1,4 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}:"
+FILESEXTRAPATHS:prepend := "${THISDIR}/${PN}:"

 SRC_URI += "file://tslib.patch"

--- a/recipes-graphics/xorg-xserver/libdri2_git.bb
+++ b/recipes-graphics/xorg-xserver/libdri2_git.bb
@@ -1,6 +1,6 @@
 DESCRIPTION = "Library for the DRI2 extension to the X Window System"

-LICENSE = "MIT-X"
+LICENSE = "MIT-CMU"
 LIC_FILES_CHKSUM = "file://COPYING;md5=827da9afab1f727f2a66574629e0f39c"

 DEPENDS = "libdrm libxext libxfixes xorgproto"
@@ -9,7 +9,7 @@ PE = "1"
 PV = "1.0.0+git${SRCPV}"
 SRC_URI = "git://github.com/robclark/libdri2.git;protocol=http;branch=master"

-SRCREV_pn-${PN} = "4f1eef3183df2b270c3d5cbef07343ee5127a6a4"
+SRCREV = "4f1eef3183df2b270c3d5cbef07343ee5127a6a4"

 S = "${WORKDIR}/git"

--- a/recipes-graphics/xorg-xserver/xf86-video-fbturbo_git.bb
+++ b/recipes-graphics/xorg-xserver/xf86-video-fbturbo_git.bb
@@ -2,14 +2,14 @@ require recipes-graphics/xorg-driver/xorg-driver-video.inc

 DESCRIPTION = "X.Org X server -- A10/A13 display driver"

-LICENSE = "MIT-X"
+LICENSE = "MIT-CMU"
 LIC_FILES_CHKSUM = "file://COPYING;md5=f91dc3ee5ce59eb4b528e67e98a31266"

 DEPENDS += "sunxi-mali libump xorgproto"

 PE = "3"
 PV = "0.5.1+git${SRCPV}"
-SRCREV_pn-${PN} = "e094e3c8f9004ca3347694bd05b99d136e8621b9"
+SRCREV = "e094e3c8f9004ca3347694bd05b99d136e8621b9"

 SRC_URI = "git://github.com/ssvb/xf86-video-fbturbo.git;protocol=http;branch=master \
           file://20-fbturbo.conf"
@@ -18,9 +18,9 @@ S = "${WORKDIR}/git"

 CFLAGS += " -I${STAGING_INCDIR}/xorg "

-do_install_append() {
+do_install:append() {
    install -d ${D}${datadir}/X11/xorg.conf.d
-    install -m 0644 ${WORKDIR}/20-fbturbo.conf ${D}${datadir}/X11/xorg.conf.d
+    install -m 0644 ${UNPACKDIR}/20-fbturbo.conf ${D}${datadir}/X11/xorg.conf.d
 }

-FILES_${PN} += "${datadir}/X11/xorg.conf.d/20-fbturbo.conf"
+FILES:${PN} += "${datadir}/X11/xorg.conf.d/20-fbturbo.conf"
--- a/recipes-graphics/xorg-xserver/xserver-xf86-config_0.1.bbappend
+++ b/recipes-graphics/xorg-xserver/xserver-xf86-config_0.1.bbappend
@@ -1 +1 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}:"
+FILESEXTRAPATHS:prepend := "${THISDIR}/${PN}:"
--- a/recipes-graphics/xorg-xserver/xserver-xorg_%.bbappend
+++ b/recipes-graphics/xorg-xserver/xserver-xorg_%.bbappend
@@ -0,0 +1 @@
+PACKAGECONFIG[dri3] = "-Ddri3=true,-Ddri3=false,libxshmfence"
--- a/recipes-kernel/armbian-firmware/armbian-firmware_git.bb
+++ b/recipes-kernel/armbian-firmware/armbian-firmware_git.bb
@@ -0,0 +1,37 @@
+SUMMARY = "Armbian Firmware"
+DESCRIPTION = "Collection of firmware files necessary for Armbian supported hardware devices to work correctly with the Linux kernel"
+LICENSE = "CLOSED"
+
+PV = "1.0+git"
+SRC_URI = "git://github.com/armbian/firmware.git;protocol=https;branch=master"
+SRCREV = "4050e02da2dce2b74c97101f7964ecfb962f5aec"
+
+S = "${WORKDIR}/git"
+
+inherit allarch
+
+do_compile[noexec] = "1"
+
+do_install() {
+    # ap6212 (bluetooth firmware only, wifi firmware is provided by linux-firmware-bcm43430)
+    install -d "${D}${nonarch_base_libdir}/firmware/ap6212"
+    install -m 0644 "${S}/ap6212/bcm43438a1.hcd" "${D}${nonarch_base_libdir}/firmware/ap6212/"
+    install -d "${D}${nonarch_base_libdir}/firmware/brcm"
+    ln -sf ../ap6212/bcm43438a1.hcd "${D}${nonarch_base_libdir}/firmware/brcm/BCM43430A1.hcd"
+}
+
+PACKAGES =+ " \
+    ${PN}-ap6212 \
+"
+
+FILES:${PN}-ap6212 = " \
+    ${nonarch_base_libdir}/firmware/ap6212/* \
+    ${nonarch_base_libdir}/firmware/brcm/BCM43430A1.hcd \
+"
+
+
+# Make armbian-firmware depend on all of the split-out packages.
+python populate_packages:prepend () {
+    firmware_pkgs = oe.utils.packages_filter_out_system(d)
+    d.appendVar('RRECOMMENDS:armbian-firmware', ' ' + ' '.join(firmware_pkgs))
+}
--- a/recipes-kernel/linux-firmware/linux-firmware_%.bbappend
+++ b/recipes-kernel/linux-firmware/linux-firmware_%.bbappend
@@ -6,8 +6,21 @@
 # WARNING: The following commit is required for NVRAM files to be included in
 # linux-firmware-bcm43430 package:
 # http://git.openembedded.org/openembedded-core/commit/?id=dde0f79f32fa6bab045ef60199903f74c4cc3393
-do_install_append() {
+do_install:append:sunxi() {
 	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.xunlong,orangepi-zero-plus2.txt
 	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.xunlong,orangepi-zero-plus2-h3.txt
 	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.friendlyarm,nanopi-neo-plus2.txt
+	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.AP6212.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-berry.txt
+}
+
+do_install:append:cubieboard4() {
+	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.bin ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.cubietech,a80-cubieboard4.bin
+}
+
+do_install:append:merrii-a80-optimus() {
+	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.bin ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.merrii,a80-optimus.bin
+}
+
+do_install:append:sun9i() {
+	ln -sf -r ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.Prowise-PT301.txt ${D}${nonarch_base_libdir}/firmware/brcm/brcmfmac4330-sdio.txt
 }
--- a/recipes-kernel/linux/linux-mainline.inc
+++ b/recipes-kernel/linux/linux-mainline.inc
@@ -1,12 +1,14 @@
 SECTION = "kernel"
-LICENSE = "GPLv2"
+LICENSE = "GPL-2.0-only"
 LIC_FILES_CHKSUM = "file://COPYING;md5=bbea815ee2795b2f4230826c0c6b8814"
-COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun50i)"
+COMPATIBLE_MACHINE = "(sun4i|sun5i|sun7i|sun8i|sun9i|sun50i)"

 inherit kernel

 require linux.inc

+LINUX_VERSION = "${PV}"
+
 # Since we're not using git, this doesn't make a difference, but we need to fill
 # in something or kernel-yocto.bbclass will fail.
 KBRANCH ?= "master"
@@ -20,13 +22,34 @@ KERNEL_EXTRA_ARGS += "LOADADDR=${UBOOT_ENTRYPOINT}"

 S = "${WORKDIR}/linux-${PV}"

-SRC_URI = "https://www.kernel.org/pub/linux/kernel/v5.x/linux-${PV}.tar.xz \
-	file://0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch \
-	file://0001-dts-orange-pi-zero-Add-wifi-support.patch \
-	file://defconfig \
+# get release version 5.x or 6.x based on version
+KRELEASE = "${@d.getVar('PV', True).split('.')[0]}"
+
+SRC_URI = "https://www.kernel.org/pub/linux/kernel/v${KRELEASE}.x/linux-${PV}.tar.xz \
+	   file://defconfig \
+	   file://sunxi-kmeta;type=kmeta;name=sunxi-kmeta;destsuffix=sunxi-kmeta \
 "

-SRC_URI_append_use-mailine-graphics = " file://drm.cfg"
-SRC_URI_append_bananapi = " file://axp20x.cfg"
+# patches
+SRC_URI:append = " \
+	file://patches/0001-dts-orangepi-zero-Add-wifi-support.patch \
+	file://patches/0002-dts-nanopi-neo-air-Add-camera-support.patch \
+	file://patches/0003-dts-allwinner-bananapi-m2-zero-Enforce-consistent-MM.patch \
+	file://patches/0004-dts-allwinner-bananapi-m64-Consistent-nodes-for-mmc-devices.patch \
+	file://patches/0005-ARM-dts-sunxi-Add-MMC-alias-for-consistent-enumerati.patch \
+	file://patches/0006-dts-allwinner-orangepi-zero-mmc-aliases-for-consiste.patch \
+"

-FILES_${KERNEL_PACKAGE_NAME}-base_append = " ${nonarch_base_libdir}/modules/${KERNEL_VERSION}/modules.builtin.modinfo"
+SRC_URI:append:use-mailine-graphics = " file://drm.cfg"
+SRC_URI:append:bananapi = " file://axp20x.cfg"
+SRC_URI:append:bananapi-m2-berry = " file://axp20x.cfg"
+SRC_URI:append:bananapi-m2-zero = " file://axp20x.cfg"
+SRC_URI:append:cubietruck = " file://axp20x.cfg"
+SRC_URI:append:nanopi-neo-air = " file://cam500b.cfg"
+SRC_URI:append:orange-pi-prime = " \
+	file://0001-dts-sun50i-h5-enable-power-button-for-orange-pi-prime.patch \
+	file://0002-dts-sun50i-h5-orange-pi-prime-add-regulator.patch \
+	file://0003-dts-sun50i-h5-orange-pi-prime-add-rtl8723cs.patch \
+"
+
+FILES_${KERNEL_PACKAGE_NAME}-base:append = " ${nonarch_base_libdir}/modules/${KERNEL_VERSION}/modules.builtin.modinfo"
--- a/recipes-kernel/linux/linux-mainline/0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch
+++ b/recipes-kernel/linux/linux-mainline/0003-ARM-dts-nanopi-neo-air-Add-WiFi-eMMC.patch
@@ -1,80 +0,0 @@
-From 4ca766a768e783ee5198f1935b7f46a5df9b4a35 Mon Sep 17 00:00:00 2001
-From: Jelle van der Waa <jelle@vdwaa.nl>
-Date: Tue, 23 Jan 2018 15:58:44 -0800
-Subject: [PATCH] ARM: dts: nanopi-neo-air: Add WiFi / eMMC
-
-Enable the WiFi (AP6212) chip and eMMC support for the NanoPi NEO Air.
-
-This patch was originally submitted by Jelle van der Waa. Martin Kelly
-modified it to compile on the latest kernel, fixed up some review
-comments from Maxime Ripard, and re-tested the patch.
-
-The patch has been reworked to add back eMMC support which has been left
-out at the last backport.
-
-Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
-Cc: linux-sunxi@googlegroups.com
-Cc: devicetree@vger.kernel.org
-Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
-Signed-off-by: Martin Kelly <mkelly@xevo.com>
-Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
-Signed-off-by: Florin Sarbu <florin@resin.io>
---
- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 34 +++++++++++++++++++++++++++
- 1 file changed, 34 insertions(+)
-
-diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
-index 03ff6f8..a9331fe 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
-+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
-@@ -72,6 +72,11 @@
- 			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
- 		};
- 	};
-+
-+	wifi_pwrseq: wifi_pwrseq {
-+		compatible = "mmc-pwrseq-simple";
-+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-+	};
- };
- 
- &mmc0 {
-@@ -84,6 +89,35 @@
- 	status = "okay";
- };
- 
-+&mmc1 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&mmc1_pins_a>;
-+	vmmc-supply = <&reg_vcc3v3>;
-+	vqmmc-supply = <&reg_vcc3v3>;
-+	mmc-pwrseq = <&wifi_pwrseq>;
-+	bus-width = <4>;
-+	non-removable;
-+	status = "okay";
-+
-+	brcmf: bcrmf@1 {
-+		reg = <1>;
-+		compatible = "brcm,bcm4329-fmac";
-+		interrupt-parent = <&pio>;
-+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
-+		interrupt-names = "host-wake";
-+	};
-+};
-+
-+&mmc2 {
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&mmc2_8bit_pins>;
-+	vmmc-supply = <&reg_vcc3v3>;
-+	vqmmc-supply = <&reg_vcc3v3>;
-+	bus-width = <8>;
-+	non-removable;
-+	status = "okay";
-+};
-+
- &uart0 {
- 	pinctrl-names = "default";
- 	pinctrl-0 = <&uart0_pins_a>;
-- 
-2.11.0
-
--- a/recipes-kernel/linux/linux-mainline/aarch64/defconfig
+++ b/recipes-kernel/linux/linux-mainline/aarch64/defconfig
@@ -339,6 +339,7 @@ CONFIG_MFD_MAX77620=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
 CONFIG_MFD_SEC_CORE=y
+CONFIG_REGULATOR=y
 CONFIG_REGULATOR_AXP20X=y
 CONFIG_REGULATOR_FAN53555=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
--- a/recipes-kernel/linux/linux-mainline/cam500b.cfg
+++ b/recipes-kernel/linux/linux-mainline/cam500b.cfg
@@ -0,0 +1,6 @@
+CONFIG_MEDIA_PLATFORM_SUPPORT=y
+CONFIG_V4L_PLATFORM_DRIVERS=y
+
+CONFIG_VIDEO_OV5640=m
+CONFIG_VIDEO_SUN6I_CSI=m
+CONFIG_VIDEO_V4L2=m
--- a/recipes-kernel/linux/linux-mainline/drm.cfg
+++ b/recipes-kernel/linux/linux-mainline/drm.cfg
@@ -2,6 +2,7 @@ CONFIG_DRM=y
 CONFIG_DRM_SUN4I=y
 CONFIG_DRM_SUN8I_DW_HDMI=y
 CONFIG_DRM_SUN8I_MIXER=y
+CONFIG_IOMMU_SUPPORT=y
 CONFIG_DRM_LIMA=y
 CONFIG_DRM_PANFROST=y
 CONFIG_CMA=y
--- a/recipes-kernel/linux/linux-mainline/orange-pi-prime/0001-dts-sun50i-h5-enable-power-button-for-orange-pi-prime.patch
+++ b/recipes-kernel/linux/linux-mainline/orange-pi-prime/0001-dts-sun50i-h5-enable-power-button-for-orange-pi-prime.patch
@@ -0,0 +1,27 @@
+From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
+From: Gunjan Gupta <viraniac@gmail.com>
+Date: Sat, 15 Jul 2023 17:06:17 +0000
+Subject: arm64: dts: sun50i: h5: enable power button for orangepi prime
+
+---
+ arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 3 ++-
+ 1 file changed, 2 insertions(+), 1 deletion(-)
+
+diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+index f430acd8558f..35e09098570f 100644
+--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+@@ -63,8 +63,9 @@ gpio-keys {
+ 
+ 		key-sw4 {
+ 			label = "sw4";
+-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
+ 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+ 		};
+ 	};
+ 
+-- 
+Armbian
+
--- a/recipes-kernel/linux/linux-mainline/orange-pi-prime/0002-dts-sun50i-h5-orange-pi-prime-add-regulator.patch
+++ b/recipes-kernel/linux/linux-mainline/orange-pi-prime/0002-dts-sun50i-h5-orange-pi-prime-add-regulator.patch
@@ -0,0 +1,66 @@
+From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
+From: The-going <48602507+The-going@users.noreply.github.com>
+Date: Mon, 24 Jan 2022 19:34:31 +0300
+Subject: arm64:dts: sun50i-h5-orangepi-prime add regulator
+
+---
+ .../allwinner/sun50i-h5-orangepi-prime.dts    | 30 +++++++++++++++++++
+ 1 file changed, 30 insertions(+)
+
+diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+index 998396bc0..6dc6850c1 100644
+--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+@@ -8,6 +8,7 @@
+ 
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+ 
+ / {
+ 	model = "Xunlong Orange Pi Prime";
+@@ -93,6 +94,10 @@ wifi_pwrseq: wifi_pwrseq {
+ 	};
+ };
+ 
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+ &codec {
+ 	allwinner,audio-routing =
+ 		"Line Out", "LINEOUT",
+@@ -188,6 +193,31 @@ &ohci3 {
+ 	status = "okay";
+ };
+ 
+&r_i2c {
+	status = "okay";
+
+	reg_vdd_cpux: regulator@65 {
+		compatible = "silergy,sy8106a";
+		reg = <0x65>;
+		regulator-name = "vdd-cpux";
+		silergy,fixed-microvolt = <1200000>;
+		/*
+		 * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
+		 * however both the Armbian DVFS table and the official one
+		 * have operating points with voltage under 1.1V, and both
+		 * DVFS table are known to work properly at the lowest
+		 * operating point.
+		 *
+		 * Use 1.0V as the minimum voltage instead.
+		 */
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-ramp-delay = <200>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+ &uart0 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&uart0_pa_pins>;
+-- 
+2.25.1
--- a/recipes-kernel/linux/linux-mainline/orange-pi-prime/0003-dts-sun50i-h5-orange-pi-prime-add-rtl8723cs.patch
+++ b/recipes-kernel/linux/linux-mainline/orange-pi-prime/0003-dts-sun50i-h5-orange-pi-prime-add-rtl8723cs.patch
@@ -0,0 +1,35 @@
+From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
+From: The-going <48602507+The-going@users.noreply.github.com>
+Date: Mon, 7 Feb 2022 19:11:07 +0300
+Subject: arm64:dts: sun50i-h5-orangepi-prime add rtl8723cs
+
+---
+ arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 5 +++++
+ 1 file changed, 5 insertions(+)
+
+diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+index 8b92d5e77220..f430acd8558f 100644
+--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+@@ -25,6 +25,7 @@ reg_vcc3v3: vcc3v3 {
+ 	aliases {
+ 		ethernet0 = &emac;
+ 		serial0 = &uart0;
+		ethernet1 = &rtl8723cs;
+ 	};
+ 
+ 	chosen {
+@@ -174,6 +175,10 @@ &mmc1 {
+ 	bus-width = <4>;
+ 	non-removable;
+ 	status = "okay";
+
+	rtl8723cs: sdio_wifi@1 {
+		reg = <1>;
+	};
+ };
+ 
+ &ohci0 {
+-- 
+Armbian
+
--- a/recipes-kernel/linux/linux-mainline/patches/0001-dts-orangepi-zero-Add-wifi-support.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0001-dts-orangepi-zero-Add-wifi-support.patch
@@ -1,8 +1,20 @@
-diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
-index 84cd9c061..917986cce 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
-+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
-@@ -80,13 +80,15 @@
+From a9bad790ae9a9e9befbe8e8938b6baca84ee5138 Mon Sep 17 00:00:00 2001
+From: Marek Belisko <marek.belisko@open-nandra.com>
+Date: Tue, 24 Oct 2023 10:40:52 +0200
+Subject: [PATCH] dts: orangepi-zero: Add wifi support
+
+Upstream-Status: Pending
+
+Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
+---
+ .../allwinner/sun8i-h2-plus-orangepi-zero.dts | 46 +++++++++++++++----
+ 1 file changed, 37 insertions(+), 9 deletions(-)
+
+diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+index 3706216ff..ca94e313f 100644
+--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+@@ -80,13 +80,15 @@ status_led {
 		};
 	};
 
@@ -23,8 +35,8 @@ index 84cd9c061..917986cce 100644
 	};
 
 	reg_vdd_cpux: vdd-cpux-regulator {
-@@ -106,10 +108,12 @@
- 			  1300000 1>;
+@@ -105,10 +107,12 @@ reg_vdd_cpux: vdd-cpux-regulator {
+ 		states = <1100000 0>, <1300000 1>;
 	};
 
 -	wifi_pwrseq: wifi_pwrseq {
@@ -38,7 +50,7 @@ index 84cd9c061..917986cce 100644
 	};
 };
 
-@@ -140,9 +144,11 @@
+@@ -139,9 +143,11 @@ &mmc0 {
 };
 
 &mmc1 {
@@ -52,7 +64,7 @@ index 84cd9c061..917986cce 100644
 	non-removable;
 	status = "okay";
 
-@@ -152,6 +158,13 @@
+@@ -151,6 +157,13 @@ &mmc1 {
 	 */
 	xr819: sdio_wifi@1 {
 		reg = <1>;
@@ -66,7 +78,7 @@ index 84cd9c061..917986cce 100644
 	};
 };
 
-@@ -208,3 +221,18 @@
+@@ -207,3 +220,18 @@ &usbphy {
 	status = "okay";
 	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 };
@@ -85,3 +97,6 @@ index 84cd9c061..917986cce 100644
 +    };
 +};
 +
+-- 
+2.25.1
+
--- a/recipes-kernel/linux/linux-mainline/patches/0002-dts-nanopi-neo-air-Add-camera-support.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0002-dts-nanopi-neo-air-Add-camera-support.patch
@@ -0,0 +1,115 @@
+From e0d786f5465d2e2d977696cf0d02c70b78402291 Mon Sep 17 00:00:00 2001
+From: Marek Belisko <marek.belisko@open-nandra.com>
+Date: Tue, 24 Oct 2023 10:42:36 +0200
+Subject: [PATCH] dts:nanopi-neo-air: Add camera support
+
+Upstream-Status: Pending
+
+Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
+---
+ .../dts/allwinner/sun8i-h3-nanopi-neo-air.dts | 85 +++++++++++++++++++
+ 1 file changed, 85 insertions(+)
+
+diff --git a/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
+index 9e1a33f94..7a05eff33 100644
+--- a/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
+@@ -77,6 +77,39 @@ wifi_pwrseq: wifi_pwrseq {
+ 		compatible = "mmc-pwrseq-simple";
+ 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ 	};
+
+        cam_xclk: cam-xclk {
+                #clock-cells = <0>;
+                compatible = "fixed-clock";
+                clock-frequency = <24000000>;
+                clock-output-names = "cam-xclk";
+        };
+
+        reg_cam_avdd: cam-avdd {
+                compatible = "regulator-fixed";
+                regulator-name = "cam-avdd";
+                regulator-min-microvolt = <2800000>;
+                regulator-max-microvolt = <2800000>;
+                vin-supply = <&reg_vcc3v3>;
+        };
+
+        reg_cam_dovdd: cam-dovdd {
+                compatible = "regulator-fixed";
+                regulator-name = "cam-dovdd";
+                regulator-min-microvolt = <1800000>;
+                regulator-max-microvolt = <1800000>;
+                vin-supply = <&reg_vcc3v3>;
+        };
+
+        reg_cam_dvdd: cam-dvdd {
+                compatible = "regulator-fixed";
+                regulator-name = "cam-dvdd";
+                regulator-min-microvolt = <1500000>;
+                regulator-max-microvolt = <1500000>;
+                vin-supply = <&reg_vcc3v3>;
+        };
+
+
+ };
+ 
+ &mmc0 {
+@@ -141,3 +174,55 @@ &usbphy {
+ 	/* USB VBUS is always on */
+ 	status = "okay";
+ };
+
+&csi {
+    status = "okay";
+
+    port {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        /* Parallel bus endpoint */
+        csi_from_ov5640: endpoint {
+            remote-endpoint = <&ov5640_to_csi>;
+            bus-width = <8>;
+            data-shift = <2>;
+            hsync-active = <1>; /* Active high */
+            vsync-active = <0>; /* Active low */
+            data-active = <1>;  /* Active high */
+            pclk-sample = <1>;  /* Rising */
+        };
+    };
+};
+
+&i2c2 {
+   status = "okay";
+
+   ov5640: camera@3c {
+        compatible = "ovti,ov5640";
+        reg = <0x3c>;
+        clocks = <&cam_xclk>;
+        clock-names = "xclk";
+
+        reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>;
+        powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>;
+        AVDD-supply = <&reg_cam_avdd>;
+        DOVDD-supply = <&reg_cam_dovdd>;
+        DVDD-supply = <&reg_cam_dvdd>;
+
+        port {
+            ov5640_to_csi: endpoint {
+                remote-endpoint = <&csi_from_ov5640>;
+                bus-width = <8>;
+                data-shift = <2>;
+                hsync-active = <1>; /* Active high */
+                vsync-active = <0>; /* Active low */
+                data-active = <1>;  /* Active high */
+                pclk-sample = <1>;  /* Rising */
+            };
+        };
+    };
+};
+&i2c2_pins {
+   bias-pull-up;
+};
+-- 
+2.25.1
+
--- a/recipes-kernel/linux/linux-mainline/patches/0003-dts-allwinner-bananapi-m2-zero-Enforce-consistent-MM.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0003-dts-allwinner-bananapi-m2-zero-Enforce-consistent-MM.patch
@@ -0,0 +1,32 @@
+From 7d7f32460702e99cab48909bb85ed84b67e65062 Mon Sep 17 00:00:00 2001
+From: Marek Belisko <marek.belisko@open-nandra.com>
+Date: Tue, 24 Oct 2023 10:43:55 +0200
+Subject: [PATCH] dts: allwinner: bananapi-m2-zero: Enforce consistent MMC
+ numbering
+
+Enforce MMC number (sometimes the order was wrong and the device does not boot).
+
+Upstream-Status: Pending
+
+Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
+---
+ arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts | 3 +++
+ 1 file changed, 3 insertions(+)
+
+diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
+index d729b7c70..410a79487 100644
+--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
+@@ -20,6 +20,9 @@ / {
+ 	aliases {
+ 		serial0 = &uart0;
+ 		serial1 = &uart1;
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+		mmc2 = &mmc2;
+ 	};
+ 
+ 	chosen {
+-- 
+2.25.1
+
--- a/recipes-kernel/linux/linux-mainline/patches/0004-dts-allwinner-bananapi-m64-Consistent-nodes-for-mmc-devices.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0004-dts-allwinner-bananapi-m64-Consistent-nodes-for-mmc-devices.patch
@@ -0,0 +1,29 @@
+From f487f62babb11d014da7a0b58a0fcdf6d217a812 Mon Sep 17 00:00:00 2001
+From: Marek Belisko <marek.belisko@open-nandra.com>
+Date: Thu, 11 May 2023 11:18:33 +0200
+Subject: [PATCH] bananapi-m64: Consistent nodes for mmc devices
+
+Upstream-Status: Pending
+
+Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
+---
+ arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 3 +++
+ 1 file changed, 3 insertions(+)
+
+diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+index e6d5bc0f7..39a28aad8 100644
+--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+@@ -16,6 +16,9 @@ aliases {
+ 		ethernet0 = &emac;
+ 		serial0 = &uart0;
+ 		serial1 = &uart1;
+                mmc0 = &mmc0;
+                mmc1 = &mmc1;
+                mmc2 = &mmc2;
+ 	};
+ 
+ 	chosen {
+-- 
+2.25.1
+
--- a/recipes-kernel/linux/linux-mainline/patches/0005-ARM-dts-sunxi-Add-MMC-alias-for-consistent-enumerati.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0005-ARM-dts-sunxi-Add-MMC-alias-for-consistent-enumerati.patch
@@ -0,0 +1,31 @@
+From 8b245b30a451bc4a4081759a6918b630ec075a7c Mon Sep 17 00:00:00 2001
+From: Stefan Gloor <code@stefan-gloor.ch>
+Date: Thu, 19 Dec 2024 10:34:54 +0100
+Subject: [PATCH] ARM: dts: sunxi: Add MMC alias for consistent enumeration
+
+Add explicit alias for MMC devices, so that (e)MMC and micro SD cards
+are enumerated consistenly. This should fix spurious boot failures when
+specifying a hard-coded root partition, e.g., mmcblk0p2.
+
+Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
+Upstream-Status: Denied https://lore.kernel.org/lkml/CAGb2v67dBhL3-AhLeHg3xOgbNZ3qu0aj9+kA+MoOMRYfr_Z_zQ@mail.gmail.com/
+---
+ arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts | 2 ++
+ 1 file changed, 2 insertions(+)
+
+diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
+index a1b89b2a2999..9cd1eb690134 100644
+--- a/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
+@@ -60,6 +60,8 @@ aliases {
+ 		serial2 = &uart7;
+ 		spi0 = &spi1;
+ 		spi1 = &spi2;
+		mmc0 = &mmc0;
+		mmc1 = &mmc3;
+ 	};
+ 
+ 	chosen {
+-- 
+2.45.2
+
--- a/recipes-kernel/linux/linux-mainline/patches/0006-dts-allwinner-orangepi-zero-mmc-aliases-for-consiste.patch
+++ b/recipes-kernel/linux/linux-mainline/patches/0006-dts-allwinner-orangepi-zero-mmc-aliases-for-consiste.patch
@@ -0,0 +1,32 @@
+From a2d765aab2989ba080b8f63cb0489d6a531cb3fd Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Oliver=20K=C3=A4stner?= <git@oliver-kaestner.de>
+Date: Sun, 16 Mar 2025 22:36:53 +0100
+Subject: [PATCH] dts: allwinner: orangepi-zero: mmc aliases for consistent
+ enumeration
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+This fixes random boot failures.
+
+Upstream-Status: Inappropriate [https://github.com/linux-sunxi/meta-sunxi/pull/431]
+
+Signed-off-by: Oliver Kästner <git@oliver-kaestner.de>
+---
+ arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts | 3 +++
+ 1 file changed, 3 insertions(+)
+
+diff --git a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+index ca94e313f..570a88327 100644
+--- a/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+@@ -59,6 +59,9 @@ aliases {
+ 		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ 		ethernet0 = &emac;
+ 		ethernet1 = &xr819;
+		mmc0 = &mmc0; /* microSD */
+		mmc1 = &mmc1; /* XR819 WiFi */
+		mmc2 = &mmc2;
+ 	};
+ 
+ 	chosen {
--- a/Show More
+++ b/Show More
				`@@ -0,0 +1 @@`
				`/home/marek/data/projects/kas/sources/meta-sunxi/recipes-devtools/python/files/olinuxino-a20lime2`
				`@@ -0,0 +1 @@`
				`PACKAGECONFIG:class-target = "opengl x11 gallium"`
				`@@ -0,0 +1 @@`
				`PACKAGECONFIG[dri3] = "-Ddri3=true,-Ddri3=false,libxshmfence"`