mirror of
https://xff.cz/git/u-boot/
synced 2025-10-31 18:35:42 +01:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
138 lines
3.3 KiB
C
138 lines
3.3 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015 Google, Inc
|
|
* Written by Simon Glass <sjg@chromium.org>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <errno.h>
|
|
#include <i2c.h>
|
|
#include <log.h>
|
|
#include <video_bridge.h>
|
|
#include <asm/global_data.h>
|
|
#include <linux/delay.h>
|
|
#include <power/regulator.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/*
|
|
* Initialisation of the chip is a process of writing certain values into
|
|
* certain registers over i2c bus. The chip in fact responds to a range of
|
|
* addresses on the i2c bus, so for each written value three parameters are
|
|
* required: i2c address, register address and the actual value.
|
|
*
|
|
* The base address is derived from the device tree, but oddly the chip
|
|
* responds on several addresses with different register sets for each.
|
|
*/
|
|
|
|
/**
|
|
* ps8622_write() Write a PS8622 eDP bridge i2c register
|
|
*
|
|
* @param dev I2C device
|
|
* @param addr_off offset from the i2c base address for ps8622
|
|
* @param reg_addr register address to write
|
|
* @param value value to be written
|
|
* @return 0 on success, non-0 on failure
|
|
*/
|
|
static int ps8622_write(struct udevice *dev, unsigned addr_off,
|
|
unsigned char reg_addr, unsigned char value)
|
|
{
|
|
struct dm_i2c_chip *chip = dev_get_parent_plat(dev);
|
|
uint8_t buf[2];
|
|
struct i2c_msg msg;
|
|
int ret;
|
|
|
|
msg.addr = chip->chip_addr + addr_off;
|
|
msg.flags = 0;
|
|
buf[0] = reg_addr;
|
|
buf[1] = value;
|
|
msg.buf = buf;
|
|
msg.len = 2;
|
|
ret = dm_i2c_xfer(dev, &msg, 1);
|
|
if (ret) {
|
|
debug("%s: write failed, reg=%#x, value=%#x, ret=%d\n",
|
|
__func__, reg_addr, value, ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ps8622_set_backlight(struct udevice *dev, int percent)
|
|
{
|
|
int level = percent * 255 / 100;
|
|
|
|
debug("%s: level=%d\n", __func__, level);
|
|
return ps8622_write(dev, 0x01, 0xa7, level);
|
|
}
|
|
|
|
static int ps8622_attach(struct udevice *dev)
|
|
{
|
|
const uint8_t *params;
|
|
struct udevice *reg;
|
|
int ret, i, len;
|
|
|
|
debug("%s: %s\n", __func__, dev->name);
|
|
/* set the LDO providing the 1.2V rail to the Parade bridge */
|
|
ret = uclass_get_device_by_phandle(UCLASS_REGULATOR, dev,
|
|
"power-supply", ®);
|
|
if (!ret) {
|
|
ret = regulator_autoset(reg);
|
|
} else if (ret != -ENOENT) {
|
|
debug("%s: Failed to enable power: ret=%d\n", __func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = video_bridge_set_active(dev, true);
|
|
if (ret)
|
|
return ret;
|
|
|
|
params = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), "parade,regs",
|
|
&len);
|
|
if (!params || len % 3) {
|
|
debug("%s: missing/invalid params=%p, len=%x\n", __func__,
|
|
params, len);
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* need to wait 20ms after power on before doing I2C writes */
|
|
mdelay(20);
|
|
for (i = 0; i < len; i += 3) {
|
|
ret = ps8622_write(dev, params[i + 0], params[i + 1],
|
|
params[i + 2]);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ps8622_probe(struct udevice *dev)
|
|
{
|
|
debug("%s\n", __func__);
|
|
if (device_get_uclass_id(dev->parent) != UCLASS_I2C)
|
|
return -EPROTONOSUPPORT;
|
|
|
|
return 0;
|
|
}
|
|
|
|
struct video_bridge_ops ps8622_ops = {
|
|
.attach = ps8622_attach,
|
|
.set_backlight = ps8622_set_backlight,
|
|
};
|
|
|
|
static const struct udevice_id ps8622_ids[] = {
|
|
{ .compatible = "parade,ps8622", },
|
|
{ .compatible = "parade,ps8625", },
|
|
{ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(parade_ps8622) = {
|
|
.name = "parade_ps8622",
|
|
.id = UCLASS_VIDEO_BRIDGE,
|
|
.of_match = ps8622_ids,
|
|
.probe = ps8622_probe,
|
|
.ops = &ps8622_ops,
|
|
};
|