mirror of
https://xff.cz/git/u-boot/
synced 2025-10-31 18:35:42 +01:00
6fe7dd3327
The DK1 and DK2 boards use the USB Type-C controller STUSB1600. This patch updates: - the device tree to add the I2C node in the DT - the board stm32mp1 to probe this I2C device and use this controller to check cable detection. - the DWC2 driver to support a new dt property "u-boot,force-b-session-valid" which forces B session and device mode; it is a workaround because the VBUS sensing and ID detection isn't available with stusb1600. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
59 lines
2.7 KiB
Plaintext
59 lines
2.7 KiB
Plaintext
Platform DesignWare HS OTG USB 2.0 controller
|
|
-----------------------------------------------------
|
|
|
|
Required properties:
|
|
- compatible : One of:
|
|
- brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC.
|
|
- hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC.
|
|
- rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc;
|
|
- "rockchip,px30-usb", "rockchip,rk3066-usb", "snps,dwc2": for px30 Soc;
|
|
- "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc;
|
|
- "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
|
|
- "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
|
|
- "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
|
|
- "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs;
|
|
- "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
|
|
- "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
|
|
- "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs;
|
|
- snps,dwc2: A generic DWC2 USB controller with default parameters.
|
|
- "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs
|
|
configured in FS mode;
|
|
- "st,stm32f4x9-hsotg": The DWC2 USB HS controller instance in STM32F4x9 SoCs
|
|
configured in HS mode;
|
|
- "st,stm32f7-hsotg": The DWC2 USB HS controller instance in STM32F7 SoCs
|
|
configured in HS mode;
|
|
- reg : Should contain 1 register range (address and length)
|
|
- interrupts : Should contain 1 interrupt
|
|
- clocks: clock provider specifier
|
|
- clock-names: shall be "otg"
|
|
Refer to clk/clock-bindings.txt for generic clock consumer properties
|
|
|
|
Optional properties:
|
|
- phys: phy provider specifier
|
|
- phy-names: shall be "usb2-phy"
|
|
Refer to phy/phy-bindings.txt for generic phy consumer properties
|
|
- dr_mode: shall be one of "host", "peripheral" and "otg"
|
|
Refer to usb/generic.txt
|
|
- g-rx-fifo-size: size of rx fifo size in gadget mode.
|
|
- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
|
|
- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
|
|
- usb33d-supply: external VBUS and ID sensing comparators supply, in order to
|
|
perform OTG operation, used on STM32MP1 SoCs.
|
|
- u-boot,force-b-session-valid: force B-peripheral session instead of relying on
|
|
VBUS sensing (only valid when dr_mode = "peripheral" and for u-boot).
|
|
|
|
Deprecated properties:
|
|
- g-use-dma: gadget DMA mode is automatically detected
|
|
|
|
Example:
|
|
|
|
usb@101c0000 {
|
|
compatible = "ralink,rt3050-usb, snps,dwc2";
|
|
reg = <0x101c0000 40000>;
|
|
interrupts = <18>;
|
|
clocks = <&usb_otg_ahb_clk>;
|
|
clock-names = "otg";
|
|
phys = <&usbphy>;
|
|
phy-names = "usb2-phy";
|
|
};
|