Tim Harvey <tharvey@gateworks.com> says:
This series will automatically add /chosen/kaslr-seed to the dt if
DM_RNG is enabled
during the boot process.
If RANDOMIZE_BASE is enabled in the Linux kernel instructing it to
randomize the virtual address at which the kernel image is loaded, it
expects entropy to be provided by the bootloader by populating
/chosen/kaslr-seed with a 64-bit value from source of entropy at boot.
If we have DM_RNG enabled populate this value automatically when
fdt_chosen is called. We skip this if ARMV8_SEC_FIRMWARE_SUPPORT
is enabled as its implementation uses a different source of entropy
that is not yet implemented as DM_RNG. We also skip this if
MEASURED_BOOT is enabled as in that case any modifications to the
dt will cause measured boot to fail (although there are many other
places the dt is altered).
As this fdt node is added elsewhere create a library function and
use it to deduplicate code. We will provide a parameter to overwrite
the node if present.
For our automatic injection, we will use the first rng device and
not overwrite if already present with a non-zero value (which may
have been populated by an earlier boot stage). This way if a board
specific ft_board_setup() function wants to customize this behavior
it can call fdt_kaslrseed with a rng device index of its choosing and
set overwrite true.
Note that the kalsrseed command (CMD_KASLRSEED) is likely pointless now
but left in place in case boot scripts exist that rely on this command
existing and returning success. An informational message is printed to
alert users of this command that it is likely no longer needed.
Note that the Kernel's EFI STUB only relies on EFI_RNG_PROTOCOL for
randomization and completely ignores the kaslr-seed for its own
randomness needs (i.e the randomization of the physical placement of
the kernel). It gets weeded out from the DTB that gets handed over via
efi_install_fdt() as it would also mess up the measured boot DTB TPM
measurements as well.
Use the fdt_kaslrseed function to deduplicate code doing the same thing.
Note that the kalsrseed command (CMD_KASLRSEED) is likely pointless now
but left in place in case boot scripts exist that rely on this command
existing and returning success. An informational message is printed to
alert users of this command that it is likely no longer needed.
Note that the Kernel's EFI STUB only relies on EFI_RNG_PROTOCOL for
randomization and completely ignores the kaslr-seed for its own
randomness needs (i.e the randomization of the physical placement of
the kernel). It gets weeded out from the DTB that gets handed over via
efi_install_fdt() as it would also mess up the measured boot DTB TPM
measurements as well.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Andy Yan <andy.yan@rock-chips.com>
Cc: Akash Gajjar <gajjar04akash@gmail.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Devarsh Thakkar <devarsht@ti.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
After adding the U_BOOT_LONGHELP macro some new commands came in still
that were not making use if it. Switch these cases over and in a few
places add missing newlines as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch corrects the mio and pll configuration registers for using usb3
on the kd240 starter kit. Without this patch, the usb3 to sd card bridge does
not initialize correctly and u-boot is unable to find the OS located on the
kd240 starter kit sd card.
In addition, this patch correctly configures mio76 and mio77 as gpio pins
which are used as reset gpio pins on the kd240 starter kit.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20240604083854.2033917-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
On Kria when board starts from Image A or Image B partition multiboot
register is already setup to that location. When reset command is called
board is issuing soft reset which start SW at already used location (offset
of multiboot * 32k).
But board should continue to run from multiboot offset 0 (start of QSPI)
and call early bootloader every reboot that's why clear multiboot register
to 0 by default to go that route all the time.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/edaf714a778bdd7447533a77b3455e4fd623f9da.1717420131.git.michal.simek@amd.com
SOC can boot out of the device which is not accessible from APU and running
this is detected as a warning, as the device is not accessible.For example
getting below warning when the boot mode is OSPI and OSPI is not enabled in
device tree.
Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)
Ignoring the prioritization of the boot device which driver is not enabled
and continue with the default boot_targets. Recommendation is to use custom
boot_targets via environment file as is done for example for Kria via
zynqmp_kria.env file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8b7cca5c7b84cb4854104e0c48f8aa63c4ec5ace.1715322156.git.michal.simek@amd.com
Once the environment was saved, the current multiboot image information
became unreachable. When dealing with firmware updates, this information
is necessary alongside the saved environment to know the booted image.
Move the multiboot environment set operation before the saved environment
check to ensure this information is always available.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240529100107.137159-1-kory.maincent@bootlin.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The zynqmp cmds.c is currently tied to the board but the commands
contained within are more closely tied to the architecture. To
allow usage of those commands when the architecture is ZynqMP but
the board is not, this change moves the cmds into the arch/ tree.
The source file is renamed to zynqmp.c to reflect the command name
as well.
Signed-off-by: Charlie Johnston <charlie.johnston@loftorbital.com>
Link: https://lore.kernel.org/r/20240410195008.405061-2-charlie.johnston@loftorbital.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Xilinx changes for v2024.07-rc1
xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding
zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant
zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update
mbv:
- Enable SPL and binman
- Small platform changes
zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path
versal-net:
- Support multiple locations for variables
Private function for finding out location of environment is not working
when ENV_IS_NOWHERE is disabled.
The reason is that current fallback is ENVL_UNKNOWN when
CONFIG_ENV_IS_NOWHERE is not enabled. The code could be updated like this
- return ENVL_NOWHERE;
+ if (IS_ENABLED(CONFIG_ENV_IS_NOWHERE))
+ return ENVL_NOWHERE;
+ return ENVL_UNKNOWN;
But then boot is still not working because ENVL_UNKNOWN has no driver and
env_init() returns -ENODEV. That's why it is better not to define board
specific env_get_location() because then weak env_get_location() is used
which is going over env_locations[] and returning locations which are
actually enabled in u-boot instance.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/830b9c93d30688cfa8a5cbb0388e79deb7731f29.1711107795.git.michal.simek@amd.com
Generally speaking, we do not prompt for this value and define it in the
board specific Kconfig file. There are some valid use cases however
today where we do prompt for this value, so instead of having this be
done in a number of locations, do this at the top-level location only.
This removes the question from a number of other locations and makes it
consistent that when we do set the value directly, we always do it the
same way. We don't need to specify the type, it's always string.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the xilinx_mbv platforms and remove
the otherwise empty file.
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
i2c1 is having all chips on it that's why use it instead of 0.
You can see this error when you boot system.
eth0: ethernet@ff0c0000
Setting bus to 0
Failure changing bus number (-19)
Enable permission for node ID 33
Enable permission for node ID 47
Hit any key to stop autoboot: 0
It also get USB to work.
Fixes: dd4a822016 ("arm64: zynqmp: Introduce kria SOM defconfig")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/cf07682a611de9895271d629ee00fb2809d99d0e.1702904913.git.michal.simek@amd.com
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
The U_BOOT_CMD_COMPLETE() macro has a semicolon at the end, perhaps
inadvertently. Some code has taken advantage of this.
Tidy this up by dropping the semicolon from the macro and adding it to
macro invocations as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In case of A/B update systems there should be an option to load the same
binary/binaries to different location and they should work.
Before this patch boot.bin with U-Boot SPL can be added to whatever 32k
offset in SPI and SPL finds u-boot.itb at CONFIG_SYS_SPI_U_BOOT_OFFS
offset. In case of A/B update systems that means that SPL is at different
locations but it still points to the same u-boot.itb which is not correct.
That's why include multiboot value to offset calculation to be able to
point to image from the same base.
It doesn't affect any current system which starts from 0 offset.
This patch also change Kria defconfig which uses A/B setup. Partition
A starts at multiboot 64, partition B at multiboot 496.
And also print message about used SPI offset which is useful for all cases.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/93903a53ad9358ae69991558b787f574797effbe.1699619666.git.michal.simek@amd.com
We can remove common.h from most cases of the code here, and only a few
places need an additional header instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@amd.com>
- Generally we just drop the #ifdef CONFIG_SYS_LONGHELP and endif lines
and use U_BOOT_LONGHELP to declare the same variable name as before
- In a few places, either rename the variable to follow convention or
introduce the variable as it was being done inline before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SelectMAP configuration interface provides an 8-bit,
16-bit or 32-bit bidirectional data bus interface to the Versal FPGA
configuration logic that can be used for both configuration and readback.
A connected microcontoller to the SelectMAP interface can load boot
image with bitstream, TF-A (ARM Trusted Firmware) and U-Boot.
This commit adds the missing identification of the SelectMAP mode.
Signed-off-by: Polak, Leszek <LPolak@arri.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/DU0PR07MB8419F7765892CDBCE7D559C5C8CFA@DU0PR07MB8419.eurprd07.prod.outlook.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
