* Add RISC-V falcon mode documentation
* Add Clang build support
* Add cmd to detect Debug Trigger Extension support
* Add PWM setting for Unmatched board
* Add Milk-V Duo board support
* Add new device node and enable new config option for VisionFive2 board
* Add second virtio device for RISC-V QEMU
Add the axp15060 regulator device. OpenSBI uses this device to perform
board reset and shutdown.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
JH7110 has a power management unit controller node. Add this node.
This device is used by OpenSBI during board reset/shutdown.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Configure the pad drive strength register for both PHYs.
The values correspond to what can be found in the Linux DTS
for VisionFive2 v1.3b.
Pad drive strength configuration is required for the phy0 to work correctly
with 100Mbit links.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This ports the pad drive strength register configuration which can be
already found in the Linux driver for this PHY.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support for Sophgo's Milk-V Duo board, only minimal device tree and
serial console are enabled, and it can boot via vendor first stage
bootloader.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Import device tree from Linux kernel to add basic support for CPU, PLIC,
UART and Timer. The name cv1800b in the filename represent the chip used
on Milk-V Duo board.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The VisionFive 2 board supports saving the u-boot environment settings
are saved to on-board SPI flash. However the defconfig enables both
ENV_IS_NOWHERE and ENV_IS_IN_SPI_FLASH, preventing the "saveenv" command
to work. Fix that by disabling ENV_IS_NOWHERE.
Fixes: 7d79bed00c ("configs: starfive: Enable environment in SPI flash support")
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The -ffixed-gp option of GCC has an exact equivalent of -ffixed-x3 in
Clang.
Signed-off-by: kleines Filmröllchen <filmroellchen@serenityos.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
QEMU RISC-V supports multiple virtio devices, but only tries to boot to
the first one. Enable support for a second virtio device, that is useful
for instance to boot on a disk image + an installer. Ideally that should
be made dynamic, but that's a first step.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The difference between the StarFive VisionFive 2 1.2A and 1.3B boards is
handled dynamically by looking at the PCB version in the EEPROM in order
to have a single u-boot version for both versions of the board. While
the "model" property is correctly handled, the "compatible" one is
always the the one of version 1.3b.
This patch add support for dynamically configuring that property.
Fixes: 9b7060bd15 ("riscv: dts: jh7110: Combine the board device tree files of 1.2A and 1.3B")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In Falcon Boot mode, the fdt blob should be move to the RAM from
kernel BSS section. To avoid being cleared by BSS initialisation.
SPL_PAYLOAD_ARGS_ADDR is the address where SPL copies.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add documentation to introduce the Falcon Mode on RISC-V.
In this mode, the boot sequence is SPL -> OpenSBI -> Linux kernel.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Latest RPi5 EEPROM firmware versions after "DATE: 2023/10/30", has changed
kernel load address from 0x80000 to 0x200000 which break boot process.
Switch to position independent code to be able to boot the same binary
on top of different EEPROM firmware versions.
Tested on:
Raspberry Pi 5 Model B Rev 1.0
Raspberry Pi 4 Model B Rev 1.1
Raspberry Pi 3 Model B Plus Rev 1.3
Raspberry Pi Zero 2 W Rev 1.0
Raspberry Pi 2 Model B Rev 1.2
Raspberry Pi Compute Module 4 Rev 1.0
Raspberry Pi Compute Module 3 Rev 1.0
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Make sure that core SDHCI accessors are used and add
device specific card detection initialization, which
is borrowed from vendor Linux driver code.
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
brcm,bcm2708-fb device provided by firmware on RPi5 uses
16 bits per pixel, so lets calculate framebuffer bytes
per pixel dynamically based on queried information.
Tested to work for RPi2b v1.2, RPi3b v1.3, RPi4b v1.1,
RPi2 Zero W, RPi5b v1.0.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Firmware on RPi5 return error on board revision query
through firmware interface, but on the other hand it fills
"linux,revision" in "system" node, so use it to detect board
revision.
system {
linux,revision = <0xc04170>;
linux,serial = <0x6cf44e80 0x3c533ede>;
};
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This includes:
* 1GB of RAM (from 4GB or 8GB total)
* AXI ranges (main peripherals)
When HDMI cable is plugged in at boot time firmware will
insert "simple-framebuffer" device into devicetree and will
shrink first memory region to 0x3f800000UL. Board setup then
will properly reserve framebuffer region.
When no HDMI cable is plugged in the size of the region will
be 0x3fc00000UL.
Signed-off-by: Dmitry Malkin <dmitry@bedrocksystems.com>
Tested-by: Jens Maus <mail@jens-maus.de>
Tested-by: Darko Alavanja <darko.alavanja@konsulko.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Currently, clock consumers cannot take any programmatic action based on the
return code of a clock function. This is because there is no
standardization, and generally no way of separating e.g. "there was a major
problem setting the rate for this clock" which usually should not be
recovered from, from "this clock doesn't support setting its rate" or "this
clock doesn't support *this* rate" which could be absolutely fine depending
on the driver.
This commit aims to standardize the acceptable codes which may be returned
from clock operations. In general,
- ENOSYS should be returned when an operation is not supported for a
particular clock.
- ENOENT may be returned if the clock ID is invalid. However, it is
encouraged to move any checks to request() to reduce code duplication.
- EINVAL should be returned for logical errors only (such as requesting an
invalid rate).
Each function has had specific guidance added for when to return each error
code. This is just guidance for now; most of the clock subsystem does not
yet conform to this standard. However, it is expected that new clock
drivers return these error codes.
Additionally, this commit adds expected behavior for each of the clock
operations. I believe these should be mostly straightforward and correspond
to existing behavior. I remember not understanding what the expected
invariants were for several clock functions, so hopefully this should help
out new driver authors. In the future, some of these invariants could be
checked via an optional config option.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231216193843.2463779-4-seanga2@gmail.com
Pull request efi-2024-04-rc1-4
Documentation:
* uefi: remove ".py" suffix for pytest.py command
* correct date in migration plan for CONFIG_DM
UEFI:
* fix conflicting SPDX license in RISC-V EFI linker scripts
* page align EFI binary section in RISC-V EFI binaries
* separate .data and .text sections of RISC-V EFI binaries
* use common function to get EFI configuration table
Without explicit support for VIDEO_X2R10G10B10 VIDEO_X8R8G8B8 white
will be rendered as cyan-ish. The conversion leaves to lowest 2 bits
unset for more compact code.
Signed-off-by: Janne Grunau <j@jannau.net>
In the non-redundant code for env_sf_save(), a failure to malloc() the
temporary buffer produces the following output:
Saving Environment to SPIFlash... OK
This is misleading as the flash has neither been erased nor written.
Fix it to return an error to the caller, so the output will be:
Saving Environment to SPIFlash... Failed (-12)
Note that there is another copy of env_sf_save() in the same file, for
handling redundant environment, and it already has the same logic.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Use device-tree node property names for parsing nodes instead of
indexing as indexing could be different between different SoCs based on
number of DSS entities available on that particular SoC.
Also correct the video layer naming in driver to match to actual one
being used in upstream DSS device-tree node [1].
This also fixes AM62x splash screen usage using the latest upstream DSS
device-tree nodes where hard-coded indexing which driver was using
before this patch was not matching the correct properties in the DT
node.
[1]: Upstream AM62x DSS node:
https://github.com/torvalds/linux/blob/v6.8-rc1/arch/arm64/boot/dts/ti/k3-am62-main.dtsi#L774
Fixes: 5f9f816bb8 ("drivers: video: tidss: TIDSS video driver support for AM62x")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Don't compile ubifs splash mount command for SPL build as this command
is not supported (and also not enabled) during SPL stage.
This fixes below compilation error, when CONFIG_CMD_UBIFS is enabled in
defconfig along with splash screen enabled at SPL stage:
"aarch64-none-linux-gnu-ld.bfd: common/cli.o: in function `run_command':
u-boot-next/u-boot/common/cli.c:51: undefined reference to
`parse_string_outer'
u-boot-next/u-boot/common/cli.c:51:(.text.run_command+0x10): relocation
truncated to fit: R_AARCH64_JUMP26 against undefined symbol
`parse_string_outer' make[2]: ***
[u-boot-next/u-boot/scripts/Makefile.spl:527: spl/u-boot-spl] Error 1
make[1]: *** [u-boot-next/u-boot/Makefile:2053: spl/u-boot-spl] Error 2
make[1]: Leaving directory 'u-boot-next/u-boot/out/a53' make: ***
[Makefile:177: sub-make] Error 2"
Fixes: eb9217dc03 ("common: Enable splash functions at SPL")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Add details regarding scheme which need to be followed in SPL and
further stages for those regions which need to be preserved across
bootstages.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium>
Add info regarding splash screen, video, bloblist and GPIO related
Kconfigs which were missing in the documentation.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium>
