Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.
However this driver is only verified with SD memory cards.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
MPC8349 has been using mpc85xx DDR driver through a symbolic link to
mpc85xx_ddr_gen2.c. After consolidating the drivers to a single set
under driver/ddr/fsl/, the link is replaced by referring driver
directly. We now can simply enable the macro and use the driver.
Other mpc83xx SoCs still use their own driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Usually CONFIG_FSL_DDR_INTERACTIVE feature is used for debug.
we would not enable this by default to save the limited space of u-boot.
This avoid following compiling error:
section .bootpg loaded at [00000000effff000,00000000effff577] overlap ssection
.data loaded at [00000000efff31b8,00000000f00010c7]
u-boot: section .bootpg lma 0xeffff000 adjusted to 0xf00010c8
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In new board P1010RDB-PB, the interrupt vector table is at
the start of memory. So if the start_address needs to be set
a proper value.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Added chip type detection and twl6032
support in the battery control
and charge functions.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
The data struct is used to support different
PMIC chip types. It contains the chip type and
the data (e.g. registers addresses, adc multiplier)
which is different for twl6030 and twl6032.
Replaced some hardcoded values with the
structure vars.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
Add support for the 16 bits pca9555 i2c to gpio extender featured
by the SB-T335 baseboard.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for status LED. Use the STATUS_LED APIs for indicating a
boot progress.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.
Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, if the
CONFIG_SYS_NO_FLASH defined later than include/config_cmd_default.h,
These two commands will be included always.
So move CONFIG_SYS_NO_FLASH definition to proper position.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The SPI section is already defined in this file (lines 268-288) so we can
remove the duplicate definitions. While at it, also fix one tiny whitespace
typo.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port.
Add support for it.
This patch allows the SPI NOR flash to be succesfully detected:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
OCOTP driver is currently selected via CONFIG_MXC_OCOTP option.
Remove the old OCOTP related options, as they are not used anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
CONFIG_SYS_NS16550_CLK specifies the rate of the clock 16x the baud
rate. The SMSC FDC37M81x datasheet states that a divider of 1 results in
a UART at 115200 baud, thus the x16 clock rate is 115200 * 16.
Previously the divider was left at 0 which led to a rate of 38400 baud
regardless of CONFIG_BAUDRATE or the baudrate environment variable.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
