When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Upstream Linux commit 87dd96111b0b.
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-5-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
When the device port is in a low power state [U3/L2/Not Connected],
accesses to usb device registers may take a long time. This could lead to
potential core hang when the controller registers are accessed after the
port is disabled by setting DEVDS field. Setting the fast register access
bit ensures that the PHY clock is keeping up in active state.
Therefore, set fast access bit to ensure the accesses to device registers
are quick even in low power states.
commit b5148d946f45 ("usb: cdns3: gadget: set fast access bit") in the
upstream kernel is taken as reference.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240424073911.1943-1-r-gunasekaran@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Allwinner F1C100s SoC has a MUSB controller like the one in the A33,
but needs an SRAM region to be claimed like the A10. We do the latter
anyway, even on chips that don't need it, so there is no real difference
in our compatible string matching.
Add a mapping between the config struct used in the Linux to our
requirements here on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Discovered while trying to use the second interface in the USB keyboard
driver necessary on Apple USB keyboards.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
The xhci driver currently only does the necessary initialization for
endpoints found in the first interface descriptor. Apple USB keyboards
(released 2021) use the second interface descriptor for the HID keyboard
boot protocol. To allow USB drivers to use endpoints from other
interface descriptors the xhci driver needs to ensure these endpoints
are initialized as well.
Use USB_MAX_ACTIVE_INTERFACES to control how many interface descriptors
are considered during endpoint initialisation.
For now define it to 2 as that is sufficient for supporting the Apple
keyboards.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
In the next step endpoints for multiple interfaces are set up. Move most
of the per endpoint initialization to separate function to avoid another
identation level.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Janne Grunau <j@jannau.net>
UFS storage often uses a 4096-byte sector size, add support for dynamic
sector sizes based loosely on the Linux implementation.
Support for dynamic sector sizes changes the types used in some
divisions, resulting in the compiler attempting to use
libgcc helpers (__aeabi_ldivmod).
Replace these divisions with calls to lldiv() to handle this correctly.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20240320-b4-qcom-usb-v4-4-41be480172e1@linaro.org
[mkorpershoek: squashed the lldiv() fix from caleb]
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
RK3036 is using the USB product id normally used by RK3066B, and RK3328
is using the product id normally used by RK3368.
Fix this and update the default USB_GADGET_PRODUCT_NUM Kconfig option
for remaining supported Rockchip SoCs to match the product id used in
Maskrom mode.
Also remove a reference to an undefined ROCKCHIP_RK3229 Kconfig symbol.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
No device tree in U-Boot or linux use the wrong spelling used in code.
Use correct property name as defined in dwc3 bindings.
Fixes: 062790f461 ("usb: xhci-dwc3: Add USB2 PHY configuration")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add support for a vbus-supply regulator specified in devicetree. This
provides generic support to avoid hardcoded GPIO configuration in board
init code.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
i.MX93 uses the same USB IP as i.MX8MM. It can then reuse the ehci-mx6
driver.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Complete the transition away from xhci-dwc3 and dwc3-of-simple drivers
and change to use the dwc3-generic driver on remaining RK3328 and RK3399
boards.
MISC, USB_DWC3 and USB_DWC3_GENERIC is enabled on boards that used to
enable USB_XHCI_DWC3. USB_XHCI_DWC3 is dropped from updated boards along
with the default y of USB_XHCI_DWC3_OF_SIMPLE.
There is no intended change in functionality with this changes, USB 3.0
is expected to continue same as before this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently u-boot fastboot can only send one message back to host,
so if there is a need to print more than one line messages must be
kept sending until all the required data is obtained. This behavior
can be adjusted using multiresponce ability (getting multiple lines
of response) proposed in this patch.
Signed-off-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240105072212.6615-2-clamor95@gmail.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Compiling with CONFIG_USB_XHCI_PCI and CONFIG_PCI=n results in
usb/host/xhci-pci.c:48:(.text.xhci_pci_probe+0x44):
undefined reference to `dm_pci_write_config32
Add the missing Kconfig dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Like Rockchip RK3328 and RK3568, the RK3588 also have a single node to
represent the glue and ctrl for USB 3.0.
Use rk_ops as driver data to select correct ctrl node for RK3588 DWC3.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
We need to get the DMA address before incrementing the pointer, as that
might move us onto another segment.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Now that we always check the return value, just return NULL on timeouts.
We can still log the error since this is a problem, but it's not reason
to panic.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
This isn't going to work, don't pretend it will and then end up timing
out.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is currently no codepath to recover from this case. In principle
we could require that the upper layer do this explicitly, but let's just
do it in xHCI when the next bulk transfer is started, since that
reasonably implies whatever caused the problem has been dealt with.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is a race where an endpoint may halt by itself while we are trying
to halt it, which results in a context state error. See xHCI 4.6.9 which
mentions this case.
This also avoids BUGging when we attempt to stop an endpoint which was
already stopped to begin with, which is probably a bug elsewhere but
not a good reason to crash.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
If the xHC has a problem with our STOP ENDPOINT command, it is likely to
return a completion directly instead of first a transfer event for the
in-progress transfer. Handle that more gracefully.
We still BUG() on the error code, but at least we don't end up timing
out on the event and ending up with unexpected event errors.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
xhci_wait_for_event returns NULL on timeout, so the caller always has to
check for that. This addresses immediate explosions in this part
of the code when timeouts happen, but not the root cause for the
timeout.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
Since {read,write}s{l, w, b}() functions are now supported in linux/io.h
there is no need to add custom implementation to driver.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Directly including asm-generic/io.h may break build because it will
cause redefenition of generic io macros if linux/io.h gets included
later, hence replace it with direct include of linux/io.h
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
At some point when trying to use USB gadgets, two situations may arise
and lead to a failure. Either the UDC (USB Device Controller) is not
available at all (not described or not probed) or the UDC is already in
use. For instance, as the USB Ethernet gadget remains bound to the UDC,
the use of any other USB gadget (fastboot, dfu, etc) *after* will always
fail with the "couldn't find an available UDC" error.
Let's give a more helpful message by making a difference between the two
cases. Let's also hint people who would get this error and grep it into
the sources a better explanation of what's wrong with their workflow.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20231010090304.49335-4-miquel.raynal@bootlin.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Exit the UMS handler loop in case START-STOP UNIT SCSI command is
received. This is sent e.g. by the util-linux eject(1) command and
indicates to the device that it is supposed to spin down the media
and enter low power state.
This effectively adds support for exitting the 'ums' command from
host using 'eject /dev/sdN' that is on par with 'dfu-util -e' .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20231107001018.55640-1-marex@denx.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
