The DM37 and OMAP35 SOM-LV share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
The DM37 and OMAP35 Torpedo share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
With the feature of OF_UPSTREAM now available, the device trees
for the SOM and baseboard can now deleted and the device tree
locations need to point to the ti/omap directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT reference from Makefile.
The da850-evm can remove the U-Boot device trees if migrated
to OF_UPSTREAM. This means pointing the device trees to the
ti/davinci directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
v2: Remove DTS from Makefile.
While the Turing RK1 board has a pad on the PCB for SPI flash, it is
not populated at the factory: supporting SPI flash boot is a user
modification, not an out-of-the-box feature. The defconfig for this
board should therefore not be enabling the SPI flash image nor SPI
support in the SPL, as it causes confusion among downstream users as to
whether the SPI image needs to be distributed.
Fixes: 153ac950a5 ("board: rockchip: Add the Turing RK1 SoM")
Suggested-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Acked-by: Joshua Riek <jjriek@verizon.net>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of using the local rv1108 devicetree copies from U-Boot,
let's convert the rv1108 boards to OF_UPSTREAM so that the upstream kernel
devicetrees can be used instead.
Tested on a rv1108-elgin-r1 board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RK3588 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is not migrated to use OF_UPSTREAM:
- generic-rk3588: Generic target only meant for U-Boot use
- toybrick-rk3588: Merged in v6.9-rc1
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RK356x boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is not migrated to use OF_UPSTREAM:
- anbernic-rgxx3-rk3566: Multi device target
- generic-rk3568: Generic target only meant for U-Boot use
- pinetab2-rk3566: Merged in v6.9-rc1
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3399 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate RK3399 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following target is not migrated to use OF_UPSTREAM:
- nanopi-m4-2gb-rk3399: DDR3 variant of nanopi-m4-rk3399 (LPDDR3)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3328 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate all RK3328 boards to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3308 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate all RK3308 boards to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-pinephone-pro device tree from Linux kernel v6.8.
Add SPI flash related node and options to support boot from SPI flash.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Add SYS_NS16550_MEM32=y to use readl/writel for serial console.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-pinebook-pro device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=10000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Add CMD_POWEROFF=y to support poweroff using cmdline and power on using
the pwr button on the board.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rockpro64 device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=10000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Add CMD_POWEROFF=y to support poweroff using cmdline and power on using
the pwr button on the board.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock-pi-4 related device tree from Linux kernel v6.8.
Add SPI flash related nodes and options to support boot from SPI flash.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support SATA HAT.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-khadas related device tree from Linux kernel v6.8.
Add SPI flash related options to support booting from SPI flash.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add CMD_ROCKUSB=y, CMD_USB_MASS_STORAGE=y and USB_GADGET=y to support
RockUSB and UMS gadget.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock960 related device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support PCIe SATA boot.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y and DM_REGULATOR_GPIO=y, boards does not use
pwm-regulator or regulator-gpio compatible.
Add USB_XHCI_HCD=y, USB_DWC3=y and USB_DWC3_GENERIC=y to support USB3.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Add CMD_ROCKUSB=y, CMD_USB_MASS_STORAGE=y and USB_GADGET=y to support
RockUSB and UMS gadget.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-nanopi-4 related device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Add PCI=y, CMD_PCI=y and NVME_PCI=y to support PCIe and NVMe boot.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support M4 SATA HAT.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y, boards does not use pwm-regulator compatible.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-roc-pc related device tree from Linux kernel v6.8.
Add SF_DEFAULT_SPEED=30000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Remove USE_PREBOOT=y to speed up booting, standard boot will init USB
after faster boot media has been evaluated.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-orangepi device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-firefly device tree from Linux kernel v6.8.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-evb device tree from Linux kernel v6.8.
Drop bootph prop for i2c0 and rk808 node, PMIC support is not included
in TPL/SPL and PMIC regulators are working fine in U-Boot proper.
Change to use sdmmc_cd pinconf and drop cd-gpios for card detect pin.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Remove CONFIG_NET_RANDOM_ETHADDR=y, ethaddr and eth1addr is set based on
cpuid read from eFUSE.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-leez-p710 device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-eaidk-610 device tree from Linux kernel v6.8.
Add DM_RESET=y to support reset signals.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y and PHY_ROCKCHIP_TYPEC=y to support USB PHY.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock-pi-n10 related device tree from Linux kernel v6.8.
Remove SPL_GPIO=y, board does not use gpio in SPL.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add MMC_SDHCI_SDMA=y to use DMA transfer for eMMC.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A few boards have shown to be required to properly configure pinctrl
for the fixed regulator gpio pin used by sdmmc before being able to read
from SD-cards.
Include the related gpio, regulator and pinctrl nodes and enable related
Kconfig options so that pinctrl can be configured in SPL for boards that
may be affected by such issue.
Also change to imply SPL_DM_SEQ_ALIAS for all boards because it must be
enabled for working gpio usage in SPL after a future DT sync.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3399 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 17 2024 - 22:54:45 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related sdhci, sdmmc and spi flash pinctrl nodes
with bootph props. Also move bootph for common nodes shared by all
boards to the SoC u-boot.dtsi.
eMMC, SD-Card and SPI flash nodes are also changed to only be tagged
with bootph props for SPL and U-Boot pre-reloc phases.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3399 SoC contain a crypto engine block that can generate random
numbers.
Imply DM_RNG and RNG_ROCKCHIP Kconfig options to take advantage of the
random generator on all RK3399 boards. Also remove the unnecessary use
of a status = "okay" prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
The RK3399 SoC support the ARMv8 Cryptography Extensions, use of ARMv8
crypto can speed up FIT checksum validation in SPL.
Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto
extensions for SHA256 when validating checksum of FIT images.
Imply SPL_FIT_SIGNATURE and LEGACY_IMAGE_FORMAT to enable FIT checksum
validation to almost all RK3399 boards.
The following boards have been excluded:
- chromebook_bob: SPL max size limitation of 120 KiB
- chromebook_kevin: SPL max size limitation of 120 KiB
Also imply OF_LIVE to help speed up init of U-Boot proper and disable
CONFIG_SPL_RAW_IMAGE_SUPPORT on leez-rk3399 to ensure SPL does not try
to jump to code that failed checksum validation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3399-ficus board is only using SPL and not TPL+SPL like all other
RK3399 boards, chromebook bob/kevin excluded. It does not seem to be any
technical reason why this board was left using only SPL.
Switch to use TPL+SPL and to use the common bss and stack addresses
introduced in commit 008ba0d56d ("rockchip: Add common default bss and
stack addresses"). Also add the missing DEFAULT_FDT_FILE option.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3399-puma board is currently using SPL stack and bss addr in SRAM,
the same addr typically used by TPL, this differs from most other RK3399
boards.
Switch to use the common bss and stack addresses introduced in commit
008ba0d56d ("rockchip: Add common default bss and stack addresses").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On rk3399-puma the FIT payload is located at sector 0x200 compared
to the more Rockchip common sector 0x4000 offset:
SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x200
Because FIT payload is located at sector 0x200 and IDBlock is located at
sector 64, the combined size of TPL+SPL (idbloader.img) cannot take up
more than 224 KiB:
(0x200 - 64) x 512 = 0x38000 (224 KiB)
Adjust SPL_PAD_TO to match the used 0x200 sector offset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chromebook bob and kevin typically run coreboot as the initial boot
loader, however, U-Boot proper can be used as a secondary boot loader.
It is also possible to run U-Boot SPL and proper bare metal, with SPL
and the U-Boot payload loaded from SPI flash.
Because of this chromebook bob and kevin only use SPL and not TPL+SPL
like other RK3399 boards, this mean that SPL is loaded to and run from
SRAM instead of DRAM.
The U-Boot payload is located at 0x40000 (256 KiB) offset in SPI flash
and because the BROM only read first 2 KiB for each 4 KiB page, the size
of SPL (idbloader.img) is limited to max 128 KiB.
The chosen bss start address further limits the size of SPL to 120 KiB.
0xff8e0000 (SPL_BSS_START_ADDR) - 0xff8c2000 (SPL_TEXT_BASE) = 0x1e000
Update SPL_MAX_SIZE to reflect the 120 KiB max size limitation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On AM62x SK we can see a boot failure with signature "alloc space
exhausted", so fix by increasing size of SPL_STACK_R_MALLOC_SIMPLE_LEN.
Fixes: 128f81290b ("arm: dts: k3: binman: am625: add support for signing TIFSSTUB Images")
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add configs related to ethernet and ethernet boot command for Sophgo Milk-V
Duo board
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add sysreset configs as well as poweroff and reset commands for Sophgo
Milk-V Duo board.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The phycore-rk3288 can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for rockchip vendor prefix accordingly.
Move device tree nodes required for u-boot to rk3288-phycore-rdk-u-boot.dtsi
such as chosen, i2c_eeprom_id and it's alias.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am64x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
While at it, drop the redundant definitions of AM642_PHYBOARD_ELECTRA_DTB
& SPL_AM642_PHYBOARD_ELECTRA_DTB from the binman dtsi file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am62x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
MD Danish Anwar <danishanwar@ti.com> says:
The series introduces device tree and config changes and AM65x
to enable ICSSG driver. The series also enables SPL_LOAD_FIT_APPLY_OVERLAY
for AM65x in order to load overlay over spl.
The ICSSG2 node is added in device tree overlay so that it remains in
sync with linux kernel.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
The users need to set env variables fw_storage_interface, fw_dev_part,
fw_ubi_mtdpart, fw_ubi_volume to indicate which storage medium and
partition they want to use to load firmware files from. By default the env
fw_storage_interface=mmc and fw_dev_part=1:2 but users can modify these
envs as per their requirements.
Enable PCIe/NVMe support on DH i.MX8M Plus DHCOM PDK3. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
In commit 51aaaf5e79 ("board: toradex: imx: Remove not needed env variables")
the empty definition of fdt_fixup variable was removed, however this was
still referenced from the boot command leading to boot failures:
## Error: \"fdt_fixup\" not defined`
Fix this by removing "run fdt_fixup" from the boot command and instead
enable CONFIG_OF_ENV_SETUP in the defconfig that would achieve the same
but in a more robust way (it works fine even if the variable is not
defined).
Fixes: 51aaaf5e79 ("board: toradex: imx: Remove not needed env variables")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
