mirror of
https://xff.cz/git/u-boot/
synced 2025-10-31 10:26:10 +01:00
arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code fine-tunes the behavior of the MMDC controller in order to improve the signal integrity and memory stability. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
This commit is contained in:
Marek Vasut
committed by
Stefano Babic
Stefano Babic
parent
44189a0328
commit
d339f16911
@@ -13,6 +13,565 @@
|
||||
#include <asm/io.h>
|
||||
#include <asm/types.h>
|
||||
|
||||
#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
|
||||
|
||||
static int wait_for_bit(void *reg, const uint32_t mask, bool set)
|
||||
{
|
||||
unsigned int timeout = 1000;
|
||||
u32 val;
|
||||
|
||||
while (--timeout) {
|
||||
val = readl(reg);
|
||||
if (!set)
|
||||
val = ~val;
|
||||
|
||||
if ((val & mask) == mask)
|
||||
return 0;
|
||||
|
||||
udelay(1);
|
||||
}
|
||||
|
||||
printf("%s: Timeout (reg=%p mask=%08x wait_set=%i)\n",
|
||||
__func__, reg, mask, set);
|
||||
hang(); /* DRAM couldn't be calibrated, game over :-( */
|
||||
}
|
||||
|
||||
static void reset_read_data_fifos(void)
|
||||
{
|
||||
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
||||
|
||||
/* Reset data FIFOs twice. */
|
||||
setbits_le32(&mmdc0->mpdgctrl0, 1 << 31);
|
||||
wait_for_bit(&mmdc0->mpdgctrl0, 1 << 31, 0);
|
||||
|
||||
setbits_le32(&mmdc0->mpdgctrl0, 1 << 31);
|
||||
wait_for_bit(&mmdc0->mpdgctrl0, 1 << 31, 0);
|
||||
}
|
||||
|
||||
static void precharge_all(const bool cs0_enable, const bool cs1_enable)
|
||||
{
|
||||
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
||||
|
||||
/*
|
||||
* Issue the Precharge-All command to the DDR device for both
|
||||
* chip selects. Note, CON_REQ bit should also remain set. If
|
||||
* only using one chip select, then precharge only the desired
|
||||
* chip select.
|
||||
*/
|
||||
if (cs0_enable) { /* CS0 */
|
||||
writel(0x04008050, &mmdc0->mdscr);
|
||||
wait_for_bit(&mmdc0->mdscr, 1 << 14, 1);
|
||||
}
|
||||
|
||||
if (cs1_enable) { /* CS1 */
|
||||
writel(0x04008058, &mmdc0->mdscr);
|
||||
wait_for_bit(&mmdc0->mdscr, 1 << 14, 1);
|
||||
}
|
||||
}
|
||||
|
||||
static void force_delay_measurement(int bus_size)
|
||||
{
|
||||
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
||||
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
||||
|
||||
writel(0x800, &mmdc0->mpmur0);
|
||||
if (bus_size == 0x2)
|
||||
writel(0x800, &mmdc1->mpmur0);
|
||||
}
|
||||
|
||||
static void modify_dg_result(u32 *reg_st0, u32 *reg_st1, u32 *reg_ctrl)
|
||||
{
|
||||
u32 dg_tmp_val, dg_dl_abs_offset, dg_hc_del, val_ctrl;
|
||||
|
||||
/*
|
||||
* DQS gating absolute offset should be modified from reflecting
|
||||
* (HW_DG_LOWx + HW_DG_UPx)/2 to reflecting (HW_DG_UPx - 0x80)
|
||||
*/
|
||||
|
||||
val_ctrl = readl(reg_ctrl);
|
||||
val_ctrl &= 0xf0000000;
|
||||
|
||||
dg_tmp_val = ((readl(reg_st0) & 0x07ff0000) >> 16) - 0xc0;
|
||||
dg_dl_abs_offset = dg_tmp_val & 0x7f;
|
||||
dg_hc_del = (dg_tmp_val & 0x780) << 1;
|
||||
|
||||
val_ctrl |= dg_dl_abs_offset + dg_hc_del;
|
||||
|
||||
dg_tmp_val = ((readl(reg_st1) & 0x07ff0000) >> 16) - 0xc0;
|
||||
dg_dl_abs_offset = dg_tmp_val & 0x7f;
|
||||
dg_hc_del = (dg_tmp_val & 0x780) << 1;
|
||||
|
||||
val_ctrl |= (dg_dl_abs_offset + dg_hc_del) << 16;
|
||||
|
||||
writel(val_ctrl, reg_ctrl);
|
||||
}
|
||||
|
||||
int mmdc_do_write_level_calibration(void)
|
||||
{
|
||||
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
||||
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
||||
u32 esdmisc_val, zq_val;
|
||||
u32 errors = 0;
|
||||
u32 ldectrl[4];
|
||||
u32 ddr_mr1 = 0x4;
|
||||
|
||||
/*
|
||||
* Stash old values in case calibration fails,
|
||||
* we need to restore them
|
||||
*/
|
||||
ldectrl[0] = readl(&mmdc0->mpwldectrl0);
|
||||
ldectrl[1] = readl(&mmdc0->mpwldectrl1);
|
||||
ldectrl[2] = readl(&mmdc1->mpwldectrl0);
|
||||
ldectrl[3] = readl(&mmdc1->mpwldectrl1);
|
||||
|
||||
/* disable DDR logic power down timer */
|
||||
clrbits_le32(&mmdc0->mdpdc, 0xff00);
|
||||
|
||||
/* disable Adopt power down timer */
|
||||
setbits_le32(&mmdc0->mapsr, 0x1);
|
||||
|
||||
debug("Starting write leveling calibration.\n");
|
||||
|
||||
/*
|
||||
* 2. disable auto refresh and ZQ calibration
|
||||
* before proceeding with Write Leveling calibration
|
||||
*/
|
||||
esdmisc_val = readl(&mmdc0->mdref);
|
||||
writel(0x0000C000, &mmdc0->mdref);
|
||||
zq_val = readl(&mmdc0->mpzqhwctrl);
|
||||
writel(zq_val & ~0x3, &mmdc0->mpzqhwctrl);
|
||||
|
||||
/* 3. increase walat and ralat to maximum */
|
||||
setbits_le32(&mmdc0->mdmisc,
|
||||
(1 << 6) | (1 << 7) | (1 << 8) | (1 << 16) | (1 << 17));
|
||||
setbits_le32(&mmdc1->mdmisc,
|
||||
(1 << 6) | (1 << 7) | (1 << 8) | (1 << 16) | (1 << 17));
|
||||
/*
|
||||
* 4 & 5. Configure the external DDR device to enter write-leveling
|
||||
* mode through Load Mode Register command.
|
||||
* Register setting:
|
||||
* Bits[31:16] MR1 value (0x0080 write leveling enable)
|
||||
* Bit[9] set WL_EN to enable MMDC DQS output
|
||||
* Bits[6:4] set CMD bits for Load Mode Register programming
|
||||
* Bits[2:0] set CMD_BA to 0x1 for DDR MR1 programming
|
||||
*/
|
||||
writel(0x00808231, &mmdc0->mdscr);
|
||||
|
||||
/* 6. Activate automatic calibration by setting MPWLGCR[HW_WL_EN] */
|
||||
writel(0x00000001, &mmdc0->mpwlgcr);
|
||||
|
||||
/*
|
||||
* 7. Upon completion of this process the MMDC de-asserts
|
||||
* the MPWLGCR[HW_WL_EN]
|
||||
*/
|
||||
wait_for_bit(&mmdc0->mpwlgcr, 1 << 0, 0);
|
||||
|
||||
/*
|
||||
* 8. check for any errors: check both PHYs for x64 configuration,
|
||||
* if x32, check only PHY0
|
||||
*/
|
||||
if (readl(&mmdc0->mpwlgcr) & 0x00000F00)
|
||||
errors |= 1;
|
||||
if (readl(&mmdc1->mpwlgcr) & 0x00000F00)
|
||||
errors |= 2;
|
||||
|
||||
debug("Ending write leveling calibration. Error mask: 0x%x\n", errors);
|
||||
|
||||
/* check to see if cal failed */
|
||||
if ((readl(&mmdc0->mpwldectrl0) == 0x001F001F) &&
|
||||
(readl(&mmdc0->mpwldectrl1) == 0x001F001F) &&
|
||||
(readl(&mmdc1->mpwldectrl0) == 0x001F001F) &&
|
||||
(readl(&mmdc1->mpwldectrl1) == 0x001F001F)) {
|
||||
debug("Cal seems to have soft-failed due to memory not supporting write leveling on all channels. Restoring original write leveling values.\n");
|
||||
writel(ldectrl[0], &mmdc0->mpwldectrl0);
|
||||
writel(ldectrl[1], &mmdc0->mpwldectrl1);
|
||||
writel(ldectrl[2], &mmdc1->mpwldectrl0);
|
||||
writel(ldectrl[3], &mmdc1->mpwldectrl1);
|
||||
errors |= 4;
|
||||
}
|
||||
|
||||
/*
|
||||
* User should issue MRS command to exit write leveling mode
|
||||
* through Load Mode Register command
|
||||
* Register setting:
|
||||
* Bits[31:16] MR1 value "ddr_mr1" value from initialization
|
||||
* Bit[9] clear WL_EN to disable MMDC DQS output
|
||||
* Bits[6:4] set CMD bits for Load Mode Register programming
|
||||
* Bits[2:0] set CMD_BA to 0x1 for DDR MR1 programming
|
||||
*/
|
||||
writel((ddr_mr1 << 16) + 0x8031, &mmdc0->mdscr);
|
||||
|
||||
/* re-enable auto refresh and zq cal */
|
||||
writel(esdmisc_val, &mmdc0->mdref);
|
||||
writel(zq_val, &mmdc0->mpzqhwctrl);
|
||||
|
||||
debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n",
|
||||
readl(&mmdc0->mpwldectrl0));
|
||||
debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n",
|
||||
readl(&mmdc0->mpwldectrl1));
|
||||
debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n",
|
||||
readl(&mmdc1->mpwldectrl0));
|
||||
debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n",
|
||||
readl(&mmdc1->mpwldectrl1));
|
||||
|
||||
/* We must force a readback of these values, to get them to stick */
|
||||
readl(&mmdc0->mpwldectrl0);
|
||||
readl(&mmdc0->mpwldectrl1);
|
||||
readl(&mmdc1->mpwldectrl0);
|
||||
readl(&mmdc1->mpwldectrl1);
|
||||
|
||||
/* enable DDR logic power down timer: */
|
||||
setbits_le32(&mmdc0->mdpdc, 0x00005500);
|
||||
|
||||
/* Enable Adopt power down timer: */
|
||||
clrbits_le32(&mmdc0->mapsr, 0x1);
|
||||
|
||||
/* Clear CON_REQ */
|
||||
writel(0, &mmdc0->mdscr);
|
||||
|
||||
return errors;
|
||||
}
|
||||
|
||||
int mmdc_do_dqs_calibration(void)
|
||||
{
|
||||
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
||||
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
||||
struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux =
|
||||
(struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE;
|
||||
bool cs0_enable;
|
||||
bool cs1_enable;
|
||||
bool cs0_enable_initial;
|
||||
bool cs1_enable_initial;
|
||||
u32 esdmisc_val;
|
||||
u32 bus_size;
|
||||
u32 temp_ref;
|
||||
u32 pddword = 0x00ffff00; /* best so far, place into MPPDCMPR1 */
|
||||
u32 errors = 0;
|
||||
u32 initdelay = 0x40404040;
|
||||
|
||||
/* check to see which chip selects are enabled */
|
||||
cs0_enable_initial = readl(&mmdc0->mdctl) & 0x80000000;
|
||||
cs1_enable_initial = readl(&mmdc0->mdctl) & 0x40000000;
|
||||
|
||||
/* disable DDR logic power down timer: */
|
||||
clrbits_le32(&mmdc0->mdpdc, 0xff00);
|
||||
|
||||
/* disable Adopt power down timer: */
|
||||
setbits_le32(&mmdc0->mapsr, 0x1);
|
||||
|
||||
/* set DQS pull ups */
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000);
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000);
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000);
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000);
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000);
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000);
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000);
|
||||
setbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000);
|
||||
|
||||
/* Save old RALAT and WALAT values */
|
||||
esdmisc_val = readl(&mmdc0->mdmisc);
|
||||
|
||||
setbits_le32(&mmdc0->mdmisc,
|
||||
(1 << 6) | (1 << 7) | (1 << 8) | (1 << 16) | (1 << 17));
|
||||
|
||||
/* Disable auto refresh before proceeding with calibration */
|
||||
temp_ref = readl(&mmdc0->mdref);
|
||||
writel(0x0000c000, &mmdc0->mdref);
|
||||
|
||||
/*
|
||||
* Per the ref manual, issue one refresh cycle MDSCR[CMD]= 0x2,
|
||||
* this also sets the CON_REQ bit.
|
||||
*/
|
||||
if (cs0_enable_initial)
|
||||
writel(0x00008020, &mmdc0->mdscr);
|
||||
if (cs1_enable_initial)
|
||||
writel(0x00008028, &mmdc0->mdscr);
|
||||
|
||||
/* poll to make sure the con_ack bit was asserted */
|
||||
wait_for_bit(&mmdc0->mdscr, 1 << 14, 1);
|
||||
|
||||
/*
|
||||
* Check MDMISC register CALIB_PER_CS to see which CS calibration
|
||||
* is targeted to (under normal cases, it should be cleared
|
||||
* as this is the default value, indicating calibration is directed
|
||||
* to CS0).
|
||||
* Disable the other chip select not being target for calibration
|
||||
* to avoid any potential issues. This will get re-enabled at end
|
||||
* of calibration.
|
||||
*/
|
||||
if ((readl(&mmdc0->mdmisc) & 0x00100000) == 0)
|
||||
clrbits_le32(&mmdc0->mdctl, 1 << 30); /* clear SDE_1 */
|
||||
else
|
||||
clrbits_le32(&mmdc0->mdctl, 1 << 31); /* clear SDE_0 */
|
||||
|
||||
/*
|
||||
* Check to see which chip selects are now enabled for
|
||||
* the remainder of the calibration.
|
||||
*/
|
||||
cs0_enable = readl(&mmdc0->mdctl) & 0x80000000;
|
||||
cs1_enable = readl(&mmdc0->mdctl) & 0x40000000;
|
||||
|
||||
/* Check to see what the data bus size is */
|
||||
bus_size = (readl(&mmdc0->mdctl) & 0x30000) >> 16;
|
||||
debug("Data bus size: %d (%d bits)\n", bus_size, 1 << (bus_size + 4));
|
||||
|
||||
precharge_all(cs0_enable, cs1_enable);
|
||||
|
||||
/* Write the pre-defined value into MPPDCMPR1 */
|
||||
writel(pddword, &mmdc0->mppdcmpr1);
|
||||
|
||||
/*
|
||||
* Issue a write access to the external DDR device by setting
|
||||
* the bit SW_DUMMY_WR (bit 0) in the MPSWDAR0 and then poll
|
||||
* this bit until it clears to indicate completion of the write access.
|
||||
*/
|
||||
setbits_le32(&mmdc0->mpswdar0, 1);
|
||||
wait_for_bit(&mmdc0->mpswdar0, 1 << 0, 0);
|
||||
|
||||
/* Set the RD_DL_ABS# bits to their default values
|
||||
* (will be calibrated later in the read delay-line calibration).
|
||||
* Both PHYs for x64 configuration, if x32, do only PHY0.
|
||||
*/
|
||||
writel(initdelay, &mmdc0->mprddlctl);
|
||||
if (bus_size == 0x2)
|
||||
writel(initdelay, &mmdc1->mprddlctl);
|
||||
|
||||
/* Force a measurment, for previous delay setup to take effect. */
|
||||
force_delay_measurement(bus_size);
|
||||
|
||||
/*
|
||||
* ***************************
|
||||
* Read DQS Gating calibration
|
||||
* ***************************
|
||||
*/
|
||||
debug("Starting Read DQS Gating calibration.\n");
|
||||
|
||||
/*
|
||||
* Reset the read data FIFOs (two resets); only need to issue reset
|
||||
* to PHY0 since in x64 mode, the reset will also go to PHY1.
|
||||
*/
|
||||
reset_read_data_fifos();
|
||||
|
||||
/*
|
||||
* Start the automatic read DQS gating calibration process by
|
||||
* asserting MPDGCTRL0[HW_DG_EN] and MPDGCTRL0[DG_CMP_CYC]
|
||||
* and then poll MPDGCTRL0[HW_DG_EN]] until this bit clears
|
||||
* to indicate completion.
|
||||
* Also, ensure that MPDGCTRL0[HW_DG_ERR] is clear to indicate
|
||||
* no errors were seen during calibration.
|
||||
*/
|
||||
|
||||
/*
|
||||
* Set bit 30: chooses option to wait 32 cycles instead of
|
||||
* 16 before comparing read data.
|
||||
*/
|
||||
setbits_le32(&mmdc0->mpdgctrl0, 1 << 30);
|
||||
|
||||
/* Set bit 28 to start automatic read DQS gating calibration */
|
||||
setbits_le32(&mmdc0->mpdgctrl0, 5 << 28);
|
||||
|
||||
/* Poll for completion. MPDGCTRL0[HW_DG_EN] should be 0 */
|
||||
wait_for_bit(&mmdc0->mpdgctrl0, 1 << 28, 0);
|
||||
|
||||
/*
|
||||
* Check to see if any errors were encountered during calibration
|
||||
* (check MPDGCTRL0[HW_DG_ERR]).
|
||||
* Check both PHYs for x64 configuration, if x32, check only PHY0.
|
||||
*/
|
||||
if (readl(&mmdc0->mpdgctrl0) & 0x00001000)
|
||||
errors |= 1;
|
||||
|
||||
if ((bus_size == 0x2) && (readl(&mmdc1->mpdgctrl0) & 0x00001000))
|
||||
errors |= 2;
|
||||
|
||||
/*
|
||||
* DQS gating absolute offset should be modified from
|
||||
* reflecting (HW_DG_LOWx + HW_DG_UPx)/2 to
|
||||
* reflecting (HW_DG_UPx - 0x80)
|
||||
*/
|
||||
modify_dg_result(&mmdc0->mpdghwst0, &mmdc0->mpdghwst1,
|
||||
&mmdc0->mpdgctrl0);
|
||||
modify_dg_result(&mmdc0->mpdghwst2, &mmdc0->mpdghwst3,
|
||||
&mmdc0->mpdgctrl1);
|
||||
if (bus_size == 0x2) {
|
||||
modify_dg_result(&mmdc1->mpdghwst0, &mmdc1->mpdghwst1,
|
||||
&mmdc1->mpdgctrl0);
|
||||
modify_dg_result(&mmdc1->mpdghwst2, &mmdc1->mpdghwst3,
|
||||
&mmdc1->mpdgctrl1);
|
||||
}
|
||||
debug("Ending Read DQS Gating calibration. Error mask: 0x%x\n", errors);
|
||||
|
||||
/*
|
||||
* **********************
|
||||
* Read Delay calibration
|
||||
* **********************
|
||||
*/
|
||||
debug("Starting Read Delay calibration.\n");
|
||||
|
||||
reset_read_data_fifos();
|
||||
|
||||
/*
|
||||
* 4. Issue the Precharge-All command to the DDR device for both
|
||||
* chip selects. If only using one chip select, then precharge
|
||||
* only the desired chip select.
|
||||
*/
|
||||
precharge_all(cs0_enable, cs1_enable);
|
||||
|
||||
/*
|
||||
* 9. Read delay-line calibration
|
||||
* Start the automatic read calibration process by asserting
|
||||
* MPRDDLHWCTL[HW_RD_DL_EN].
|
||||
*/
|
||||
writel(0x00000030, &mmdc0->mprddlhwctl);
|
||||
|
||||
/*
|
||||
* 10. poll for completion
|
||||
* MMDC indicates that the write data calibration had finished by
|
||||
* setting MPRDDLHWCTL[HW_RD_DL_EN] = 0. Also, ensure that
|
||||
* no error bits were set.
|
||||
*/
|
||||
wait_for_bit(&mmdc0->mprddlhwctl, 1 << 4, 0);
|
||||
|
||||
/* check both PHYs for x64 configuration, if x32, check only PHY0 */
|
||||
if (readl(&mmdc0->mprddlhwctl) & 0x0000000f)
|
||||
errors |= 4;
|
||||
|
||||
if ((bus_size == 0x2) && (readl(&mmdc1->mprddlhwctl) & 0x0000000f))
|
||||
errors |= 8;
|
||||
|
||||
debug("Ending Read Delay calibration. Error mask: 0x%x\n", errors);
|
||||
|
||||
/*
|
||||
* ***********************
|
||||
* Write Delay Calibration
|
||||
* ***********************
|
||||
*/
|
||||
debug("Starting Write Delay calibration.\n");
|
||||
|
||||
reset_read_data_fifos();
|
||||
|
||||
/*
|
||||
* 4. Issue the Precharge-All command to the DDR device for both
|
||||
* chip selects. If only using one chip select, then precharge
|
||||
* only the desired chip select.
|
||||
*/
|
||||
precharge_all(cs0_enable, cs1_enable);
|
||||
|
||||
/*
|
||||
* 8. Set the WR_DL_ABS# bits to their default values.
|
||||
* Both PHYs for x64 configuration, if x32, do only PHY0.
|
||||
*/
|
||||
writel(initdelay, &mmdc0->mpwrdlctl);
|
||||
if (bus_size == 0x2)
|
||||
writel(initdelay, &mmdc1->mpwrdlctl);
|
||||
|
||||
/*
|
||||
* XXX This isn't in the manual. Force a measurement,
|
||||
* for previous delay setup to effect.
|
||||
*/
|
||||
force_delay_measurement(bus_size);
|
||||
|
||||
/*
|
||||
* 9. 10. Start the automatic write calibration process
|
||||
* by asserting MPWRDLHWCTL0[HW_WR_DL_EN].
|
||||
*/
|
||||
writel(0x00000030, &mmdc0->mpwrdlhwctl);
|
||||
|
||||
/*
|
||||
* Poll for completion.
|
||||
* MMDC indicates that the write data calibration had finished
|
||||
* by setting MPWRDLHWCTL[HW_WR_DL_EN] = 0.
|
||||
* Also, ensure that no error bits were set.
|
||||
*/
|
||||
wait_for_bit(&mmdc0->mpwrdlhwctl, 1 << 4, 0);
|
||||
|
||||
/* Check both PHYs for x64 configuration, if x32, check only PHY0 */
|
||||
if (readl(&mmdc0->mpwrdlhwctl) & 0x0000000f)
|
||||
errors |= 16;
|
||||
|
||||
if ((bus_size == 0x2) && (readl(&mmdc1->mpwrdlhwctl) & 0x0000000f))
|
||||
errors |= 32;
|
||||
|
||||
debug("Ending Write Delay calibration. Error mask: 0x%x\n", errors);
|
||||
|
||||
reset_read_data_fifos();
|
||||
|
||||
/* Enable DDR logic power down timer */
|
||||
setbits_le32(&mmdc0->mdpdc, 0x00005500);
|
||||
|
||||
/* Enable Adopt power down timer */
|
||||
clrbits_le32(&mmdc0->mapsr, 0x1);
|
||||
|
||||
/* Restore MDMISC value (RALAT, WALAT) to MMDCP1 */
|
||||
writel(esdmisc_val, &mmdc0->mdmisc);
|
||||
|
||||
/* Clear DQS pull ups */
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000);
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000);
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000);
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000);
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000);
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000);
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000);
|
||||
clrbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000);
|
||||
|
||||
/* Re-enable SDE (chip selects) if they were set initially */
|
||||
if (cs1_enable_initial)
|
||||
/* Set SDE_1 */
|
||||
setbits_le32(&mmdc0->mdctl, 1 << 30);
|
||||
|
||||
if (cs0_enable_initial)
|
||||
/* Set SDE_0 */
|
||||
setbits_le32(&mmdc0->mdctl, 1 << 31);
|
||||
|
||||
/* Re-enable to auto refresh */
|
||||
writel(temp_ref, &mmdc0->mdref);
|
||||
|
||||
/* Clear the MDSCR (including the con_req bit) */
|
||||
writel(0x0, &mmdc0->mdscr); /* CS0 */
|
||||
|
||||
/* Poll to make sure the con_ack bit is clear */
|
||||
wait_for_bit(&mmdc0->mdscr, 1 << 14, 0);
|
||||
|
||||
/*
|
||||
* Print out the registers that were updated as a result
|
||||
* of the calibration process.
|
||||
*/
|
||||
debug("MMDC registers updated from calibration\n");
|
||||
debug("Read DQS gating calibration:\n");
|
||||
debug("\tMPDGCTRL0 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl0));
|
||||
debug("\tMPDGCTRL1 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl1));
|
||||
debug("\tMPDGCTRL0 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl0));
|
||||
debug("\tMPDGCTRL1 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl1));
|
||||
debug("Read calibration:\n");
|
||||
debug("\tMPRDDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mprddlctl));
|
||||
debug("\tMPRDDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mprddlctl));
|
||||
debug("Write calibration:\n");
|
||||
debug("\tMPWRDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mpwrdlctl));
|
||||
debug("\tMPWRDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mpwrdlctl));
|
||||
|
||||
/*
|
||||
* Registers below are for debugging purposes. These print out
|
||||
* the upper and lower boundaries captured during
|
||||
* read DQS gating calibration.
|
||||
*/
|
||||
debug("Status registers bounds for read DQS gating:\n");
|
||||
debug("\tMPDGHWST0 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst0));
|
||||
debug("\tMPDGHWST1 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst1));
|
||||
debug("\tMPDGHWST2 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst2));
|
||||
debug("\tMPDGHWST3 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst3));
|
||||
debug("\tMPDGHWST0 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst0));
|
||||
debug("\tMPDGHWST1 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst1));
|
||||
debug("\tMPDGHWST2 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst2));
|
||||
debug("\tMPDGHWST3 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst3));
|
||||
|
||||
debug("Final do_dqs_calibration error mask: 0x%x\n", errors);
|
||||
|
||||
return errors;
|
||||
}
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_MX6SX)
|
||||
/* Configure MX6SX mmdc iomux */
|
||||
void mx6sx_dram_iocfg(unsigned width,
|
||||
|
||||
@@ -456,6 +456,11 @@ void mx6sl_dram_iocfg(unsigned width,
|
||||
const struct mx6sl_iomux_ddr_regs *,
|
||||
const struct mx6sl_iomux_grp_regs *);
|
||||
|
||||
#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
|
||||
int mmdc_do_write_level_calibration(void);
|
||||
int mmdc_do_dqs_calibration(void);
|
||||
#endif
|
||||
|
||||
/* configure mx6 mmdc registers */
|
||||
void mx6_dram_cfg(const struct mx6_ddr_sysinfo *,
|
||||
const struct mx6_mmdc_calibration *,
|
||||
|
||||
Reference in New Issue
Block a user