Merge tag 'u-boot-amlogic-20200708' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- Add proper Odroid-N2 board support code
- Add support for Odroid-C4 single board computer

arch/arm/dts/Makefile

@@ -163,6 +163,7 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-g12b-odroid-n2.dtb \
 	meson-g12b-a311d-khadas-vim3.dtb \
 	meson-sm1-khadas-vim3l.dtb \
+	meson-sm1-odroid-c4.dtb \
 	meson-sm1-sei610.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \

arch/arm/dts/meson-g12-common.dtsi

@@ -250,6 +250,17 @@
 				};
 			};
 
+			acodec: audio-controller@32000 {
+				compatible = "amlogic,t9015";
+				reg = <0x0 0x32000 0x0 0x14>;
+				#sound-dai-cells = <0>;
+				sound-name-prefix = "ACODEC";
+				clocks = <&clkc CLKID_AUDIO_CODEC>;
+				clock-names = "pclk";
+				resets = <&reset RESET_AUDIO_CODEC>;
+				status = "disabled";
+			};
+
 			periphs: bus@34400 {
 				compatible = "simple-bus";
 				reg = <0x0 0x34400 0x0 0x400>;
@@ -2319,7 +2330,7 @@
 				reg = <0x0 0xff400000 0x0 0x40000>;
 				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
-				clock-names = "ddr";
+				clock-names = "otg";
 				phys = <&usb2_phy1>;
 				phy-names = "usb2-phy";
 				dr_mode = "peripheral";

arch/arm/dts/meson-g12.dtsi

@@ -343,6 +343,15 @@
 			status = "disabled";
 		};
 
+		toacodec: audio-controller@740 {
+			compatible = "amlogic,g12a-toacodec";
+			reg = <0x0 0x740 0x0 0x4>;
+			#sound-dai-cells = <1>;
+			sound-name-prefix = "TOACODEC";
+			resets = <&clkc_audio AUD_RESET_TOACODEC>;
+			status = "disabled";
+		};
+
 		tohdmitx: audio-controller@744 {
 			compatible = "amlogic,g12a-tohdmitx";
 			reg = <0x0 0x744 0x0 0x4>;
@@ -354,29 +363,6 @@
 	};
 };
 
-&cpu_thermal {
-	cooling-maps {
-		map0 {
-			trip = <&cpu_passive>;
-			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-		map1 {
-			trip = <&cpu_hot>;
-			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-	};
-};
-
 &ethmac {
 	power-domains = <&pwrc PWRC_G12A_ETH_ID>;
 };

arch/arm/dts/meson-g12b-khadas-vim3.dtsi

@@ -51,11 +51,11 @@
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "G12B-KHADAS-VIM3";
-		audio-aux-devs = <&tdmout_b>;
+		audio-aux-devs = <&tdmout_a>;
-		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+		audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
-				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_A IN 1", "FRDDR_B OUT 0",
-				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDMOUT_A IN 2", "FRDDR_C OUT 0",
-				"TDM_B Playback", "TDMOUT_B OUT";
+				"TDM_A Playback", "TDMOUT_A OUT";
 
 		assigned-clocks = <&clkc CLKID_MPLL2>,
 				  <&clkc CLKID_MPLL0>,
@@ -80,7 +80,7 @@
 
 		/* 8ch hdmi interface */
 		dai-link-3 {
-			sound-dai = <&tdmif_b>;
+			sound-dai = <&tdmif_a>;
 			dai-format = "i2s";
 			dai-tdm-slot-tx-mask-0 = <1 1>;
 			dai-tdm-slot-tx-mask-1 = <1 1>;
@@ -89,7 +89,7 @@
 			mclk-fs = <256>;
 
 			codec {
-				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
 			};
 		};
 
@@ -154,6 +154,10 @@
 	clock-latency = <50000>;
 };
 
+&frddr_a {
+	status = "okay";
+};
+
 &frddr_b {
 	status = "okay";
 };
@@ -178,11 +182,11 @@
 	status = "okay";
 };
 
-&tdmif_b {
+&tdmif_a {
 	status = "okay";
 };
 
-&tdmout_b {
+&tdmout_a {
 	status = "okay";
 };
 

arch/arm/dts/meson-g12b-s922x.dtsi

@@ -65,6 +65,11 @@
 			opp-hz = /bits/ 64 <1896000000>;
 			opp-microvolt = <981000>;
 		};
+
+		opp-1992000000 {
+			opp-hz = /bits/ 64 <1992000000>;
+			opp-microvolt = <1001000>;
+		};
 	};
 
 	cpub_opp_table_1: opp-table-1 {
@@ -120,5 +125,15 @@
 			opp-hz = /bits/ 64 <1704000000>;
 			opp-microvolt = <891000>;
 		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <981000>;
+		};
+
+		opp-1908000000 {
+			opp-hz = /bits/ 64 <1908000000>;
+			opp-microvolt = <1022000>;
+		};
 	};
 };

arch/arm/dts/meson-g12b.dtsi

@@ -113,3 +113,25 @@
 	compatible = "amlogic,g12b-clkc";
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			trip = <&cpu_passive>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+		map1 {
+			trip = <&cpu_hot>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					 <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};

arch/arm/dts/meson-khadas-vim3.dtsi

@@ -39,13 +39,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		white {
+		led-white {
 			label = "vim3:white:sys";
 			gpios = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		red {
+		led-red {
 			label = "vim3:red";
 			gpios = <&gpio_expander 5 GPIO_ACTIVE_LOW>;
 		};

arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi

@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
+
+&ethmac {
+	snps,reset-gpio = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+};

arch/arm/dts/meson-sm1-odroid-c4.dts

@@ -0,0 +1,402 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Dongjin Kim <tobetter@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "hardkernel,odroid-c4", "amlogic,sm1";
+	model = "Hardkernel ODROID-C4";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			panic-indicator;
+		};
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0>,
+			 <1800000 1>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&main_12v>;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	vddcpu: regulator-vddcpu {
+		/*
+		 * MP8756GD Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		vin-supply = <&main_12v>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	hub_5v: regulator-hub_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "HUB_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the Hub CHIPENABLE, LOW sets low power state */
+		gpio = <&gpio GPIOH_4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the microUSB port power enable */
+		gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
+};
+
+&gpio {
+	gpio-line-names =
+		/* GPIOZ */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		/* GPIOH */
+		"", "", "", "", "",
+		"PIN_36", /* GPIOH_5 */
+		"PIN_26", /* GPIOH_6 */
+		"PIN_32", /* GPIOH_7 */
+		"",
+		/* BOOT */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		/* GPIOC */
+		"", "", "", "", "", "", "", "",
+		/* GPIOA */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "",
+		"PIN_27", /* GPIOA_14 */
+		"PIN_28", /* GPIOA_15 */
+		/* GPIOX */
+		"PIN_16", /* GPIOX_0 */
+		"PIN_18", /* GPIOX_1 */
+		"PIN_22", /* GPIOX_2 */
+		"PIN_11", /* GPIOX_3 */
+		"PIN_13", /* GPIOX_4 */
+		"PIN_7",  /* GPIOX_5 */
+		"PIN_33", /* GPIOX_6 */
+		"PIN_15", /* GPIOX_7 */
+		"PIN_19", /* GPIOX_8 */
+		"PIN_21", /* GPIOX_9 */
+		"PIN_24", /* GPIOX_10 */
+		"PIN_23", /* GPIOX_11 */
+		"PIN_8",  /* GPIOX_12 */
+		"PIN_10", /* GPIOX_13 */
+		"PIN_29", /* GPIOX_14 */
+		"PIN_31", /* GPIOX_15 */
+		"PIN_12", /* GPIOX_16 */
+		"PIN_3",  /* GPIOX_17 */
+		"PIN_5",  /* GPIOX_18 */
+		"PIN_35"; /* GPIOX_19 */
+
+	/*
+	 * WARNING: The USB Hub on the Odroid-C4 needs a reset signal
+	 * to be turned high in order to be detected by the USB Controller
+	 * This signal should be handled by a USB specific power sequence
+	 * in order to reset the Hub when USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&gpio_ao {
+	gpio-line-names =
+		/* GPIOAO */
+		"", "", "", "",
+		"PIN_47", /* GPIOAO_4 */
+		"", "",
+		"PIN_45", /* GPIOAO_7 */
+		"PIN_46", /* GPIOAO_8 */
+		"PIN_44", /* GPIOAO_9 */
+		"PIN_42", /* GPIOAO_10 */
+		"",
+		/* GPIOE */
+		"", "", "";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+	linux,rc-map-name = "rc-odroid";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <200000000>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+	/* Enable the hub which is connected to this port */
+	phy-supply = <&hub_5v>;
+};

arch/arm/dts/meson-sm1-sei610.dts

@@ -104,7 +104,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		bluetooth {
+		led-bluetooth {
 			label = "sei610:blue:bt";
 			gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
 			default-state = "off";

arch/arm/dts/meson-sm1.dtsi

@@ -56,6 +56,7 @@
 			reg = <0x0 0x0>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
@@ -64,6 +65,7 @@
 			reg = <0x0 0x1>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		cpu2: cpu@2 {
@@ -72,6 +74,7 @@
 			reg = <0x0 0x2>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu@3 {
@@ -80,6 +83,7 @@
 			reg = <0x0 0x3>;
 			enable-method = "psci";
 			next-level-cache = <&l2>;
+			#cooling-cells = <2>;
 		};
 
 		l2: l2-cache0 {
@@ -466,6 +470,26 @@
 	compatible = "amlogic,sm1-clkc";
 };
 
+&cpu_thermal {
+	cooling-maps {
+		map0 {
+			trip = <&cpu_passive>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+
+		map1 {
+			trip = <&cpu_hot>;
+			cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
 &ethmac {
 	power-domains = <&pwrc PWRC_SM1_ETH_ID>;
 };

board/amlogic/odroid-n2/MAINTAINERS

@@ -0,0 +1,9 @@
+ODROID-N2
+M:	Neil Armstrong <narmstrong@baylibre.com>
+S:	Maintained
+L:	u-boot-amlogic@groups.io
+F:	board/amlogic/odroid-n2/
+F:	configs/odroid-n2_defconfig
+F:	configs/odroid-c4_defconfig
+F:	doc/board/amlogic/odroid-n2.rst
+F:	doc/board/amlogic/odroid-c4.rst

board/amlogic/odroid-n2/Makefile

@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2020 BayLibre, SAS
+# Author: Neil Armstrong <narmstrong@baylibre.com>
+
+obj-y	:= odroid-n2.o

board/amlogic/odroid-n2/odroid-n2.c

@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <env.h>
+#include <init.h>
+#include <net.h>
+#include <asm/io.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+
+#define EFUSE_MAC_OFFSET	20
+#define EFUSE_MAC_SIZE		12
+#define MAC_ADDR_LEN		6
+
+int misc_init_r(void)
+{
+	u8 mac_addr[MAC_ADDR_LEN];
+	char efuse_mac_addr[EFUSE_MAC_SIZE], tmp[3];
+	ssize_t len;
+
+	meson_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+	if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+		len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+					  efuse_mac_addr, EFUSE_MAC_SIZE);
+		if (len != EFUSE_MAC_SIZE)
+			return 0;
+
+		/* MAC is stored in ASCII format, 1bytes = 2characters */
+		for (int i = 0; i < 6; i++) {
+			tmp[0] = efuse_mac_addr[i * 2];
+			tmp[1] = efuse_mac_addr[i * 2 + 1];
+			tmp[2] = '\0';
+			mac_addr[i] = simple_strtoul(tmp, NULL, 16);
+		}
+
+		if (is_valid_ethaddr(mac_addr))
+			eth_env_set_enetaddr("ethaddr", mac_addr);
+		else
+			meson_generate_serial_ethaddr();
+	}
+
+	return 0;
+}

board/amlogic/w400/MAINTAINERS

@@ -5,8 +5,6 @@ L:	u-boot-amlogic@groups.io
 F:	board/amlogic/w400/
 F:	configs/khadas-vim3_defconfig
 F:	configs/khadas-vim3l_defconfig
-F:	configs/odroid-n2_defconfig
 F:	doc/board/amlogic/w400.rst
 F:	doc/board/amlogic/khadas-vim3.rst
 F:	doc/board/amlogic/khadas-vim3l.rst
-F:	doc/board/amlogic/odroid-n2.rst

configs/odroid-c4_defconfig

@@ -0,0 +1,62 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="odroid-n2"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_MESON_G12A=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" odroid-c4"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-sm1-odroid-c4"
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MESON_EE_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_DM_VIDEO=y
+CONFIG_VIDEO_MESON=y
+CONFIG_VIDEO_DT_SIMPLEFB=y
+CONFIG_OF_LIBFDT_OVERLAY=y

configs/odroid-n2_defconfig

@@ -1,5 +1,5 @@
 CONFIG_ARM=y
-CONFIG_SYS_BOARD="w400"
+CONFIG_SYS_BOARD="odroid-n2"
 CONFIG_ARCH_MESON=y
 CONFIG_SYS_TEXT_BASE=0x01000000
 CONFIG_ENV_SIZE=0x2000

doc/board/amlogic/index.rst

@@ -17,7 +17,7 @@ This matrix concerns the actual source code version.
 +===============================+===========+==============+==============+============+============+=============+==============+
 | Boards               		| Odroid-C2 | P212         | Khadas VIM2  | S400       | U200       | Odroid-N2   | SEI610       |
 |				| Nanopi-K2 | Khadas-VIM   | Libretech-PC |	       | SEI510	    | Khadas-VIM3 | Khadas-VIM3L |
-|				| P200	    | LibreTech-CC |	          |	       |            |	          |    	         |
+|				| P200	    | LibreTech-CC |	          |	       |            |	          | Odroid-C4    |
 |				| P201	    | LibreTech-AC |	          |	       |            |             |    	         |
 +-------------------------------+-----------+--------------+--------------+------------+------------+-------------+--------------+
 | UART               		| **Yes**   | **Yes**      | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
@@ -83,6 +83,7 @@ Board Documentation
    libretech-cc
    nanopi-k2
    odroid-c2
+   odroid-c4
    odroid-n2
    p200
    p201

doc/board/amlogic/odroid-c4.rst

@@ -0,0 +1,134 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for ODROID-C4
+====================
+
+ODROID-C4 is a single board computer manufactured by Hardkernel
+Co. Ltd with the following specifications:
+
+ - Amlogic S905X3 Arm Cortex-A55 quad-core SoC
+ - 4GB DDR4 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.1 display
+ - 40-pin GPIO header
+ - 4x USB 3.0 Host
+ - 1x USB 2.0 Host/OTG (micro)
+ - eMMC, microSD
+ - UART serial
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+    $ export CROSS_COMPILE=aarch64-none-elf-
+    $ make odroid-c4_defconfig
+    $ make
+
+Image creation
+--------------
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+.. code-block:: bash
+
+    $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+    $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+    $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+    $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+    $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+
+    $ DIR=odroid-c4
+    $ git clone --depth 1 \
+       https://github.com/hardkernel/u-boot.git -b odroidg12-v2015.01 \
+       $DIR
+
+    $ cd odroid-c4
+    $ make odroidc4_defconfig
+    $ make
+    $ export UBOOTDIR=$PWD
+
+Go back to mainline U-Boot source tree then :
+
+.. code-block:: bash
+
+    $ mkdir fip
+
+    $ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
+    $ cp $UBOOTDIR/build/scp_task/bl301.bin fip/
+    $ cp $UBOOTDIR/build/board/hardkernel/odroidc4/firmware/acs.bin fip/
+    $ cp $UBOOTDIR/fip/g12a/bl2.bin fip/
+    $ cp $UBOOTDIR/fip/g12a/bl30.bin fip/
+    $ cp $UBOOTDIR/fip/g12a/bl31.img fip/
+    $ cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/piei.fw fip/
+    $ cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/
+    $ cp u-boot.bin fip/bl33.bin
+
+    $ sh fip/blx_fix.sh \
+    	fip/bl30.bin \
+    	fip/zero_tmp \
+    	fip/bl30_zero.bin \
+    	fip/bl301.bin \
+    	fip/bl301_zero.bin \
+    	fip/bl30_new.bin \
+    	bl30
+
+    $ sh fip/blx_fix.sh \
+    	fip/bl2.bin \
+    	fip/zero_tmp \
+    	fip/bl2_zero.bin \
+    	fip/acs.bin \
+    	fip/bl21_zero.bin \
+    	fip/bl2_new.bin \
+    	bl2
+
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
+    					--output fip/bl30_new.bin.g12a.enc \
+    					--level v3
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
+    					--output fip/bl30_new.bin.enc \
+    					--level v3 --type bl30
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
+    					--output fip/bl31.img.enc \
+    					--level v3 --type bl31
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
+    					--output fip/bl33.bin.enc \
+    					--level v3 --type bl33 --compress lz4
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
+    					--output fip/bl2.n.bin.sig
+    $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \
+    		--output fip/u-boot.bin \
+    		--bl2 fip/bl2.n.bin.sig \
+    		--bl30 fip/bl30_new.bin.enc \
+    		--bl31 fip/bl31.img.enc \
+    		--bl33 fip/bl33.bin.enc \
+    		--ddrfw1 fip/ddr4_1d.fw \
+    		--ddrfw2 fip/ddr4_2d.fw \
+    		--ddrfw3 fip/ddr3_1d.fw \
+    		--ddrfw4 fip/piei.fw \
+    		--ddrfw5 fip/lpddr4_1d.fw \
+    		--ddrfw6 fip/lpddr4_2d.fw \
+    		--ddrfw7 fip/diag_lpddr4.fw \
+    		--ddrfw8 fip/aml_ddr.fw \
+    		--ddrfw9 fip/lpddr3_1d.fw \
+    		--level v3
+
+and then write the image to SD with:
+
+.. code-block:: bash
+
+    $ DEV=/dev/your_sd_device
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444