# I2C Puppet mods for Linux systems

The original version lacked certain characters, such as  <ESCAPE>, and the characters "<>{}[]^&%=\"
which made it difficult to use on Linux systems
    

This version of the firmware has been modified to support Linux systems.
The following changes have been made
- The backspace key works during the GUI login
- The Sym key now acts as a Control key, so SYM+C is Control-C
- The four top button keys are now used to provide the missing characters.

The original definiton of the keys were this. I'm including the
spacebar, newline/enter, backspace, Microphone and Spkeaer keys
because they provide characters not indicated on the key. For
instance, SYM + spacebar provides TAB


|      | L1    | L2    |    R1 |    R2 | SPKR | Mic| BS | NL |  SPACE  |
| ------|-------|-------|-------|-------|------|----|---|---|---------|
| none  |       |       |       |       |  $   |  ~ | \b| \n| SPACE   |
| Alt   |       |       |       |       |  \`  |  0 |   |   |         |
| Shift |       |       |       |       |  $   |    |   |   |         |
| Sym   |       |       |       |       |  $   |    |   |\| |  TAB   |



This firmware adds the following mappings


|      | L1     | L2    |    R1 |    R2 | SPKR | Mic| BS| NL|  SPACE  |
| ------|--------|-------|-------|-------|------|----|---|---|---------|
| none  | escape |  %    |  =    |  \\   |  $   |  ~ | \b| \n| SPACE |
| Alt   |  >     |  ]    |  }    |  &    |  \`  |  0 |   |   |         |
| Shift |  <     |  ]    |  {    |  ^    |  $   |  ~ | \b|   |         |
| Sym   |        |       |       |       |  $   |  ~ | \b|\| |  TAB |

## Linux Debug tips

The keyboard has two "outputs" - one is the USB HID interface, the
other is the serial port.  Any printf() command goes to the serial
port, but not the USB HID keyboard. For instance, when using an
Arduino sketch, print() goes to the serial port.

When the keyboard is plugged into a Linux system, a new TTY interface
will appear. I usually use 

	ls -lt /dev/tty* | head" 
 
to learn the name, as the newest port will appear first. On my system,
it's /dev/ttyACM0

So on one terminal window, I type

    cat -v </dev/ttyACM0

while on a second terminal window, I type

    cat -v

The first one will print all of the printf output, and the second will
show you how the keyboard works normally and what gets sent to the USB
keyboard when a key is pressed..

## Compiling firmware on Linux

I edit the files in <GIT>/ic2_puppet/all/ using my preferred
editor. In my case, I use emacs. I have the keystroke combination
"Control-C M" bound to compile, using

    (global-set-key "\C-cm" 'compile)

And when I press these keys, emacs saves all files, and recompiles the
code. I have a small hub with switchable on/off ports, and restart the
keyboard into boot mode, and then do a "make install" to load the new
firmware

## GUI Login

I found that I had to handle the backspace differently, as arturo did
for enter. This was necessary so that the backspace key would delete
the username or password characters.

## TODO

Currently - the SYM+Button keys are defined as the character "x" to indicate it's not been specified.
I'l like to make these keys to the 4 arrow keys.

Also - it might be possible to create key combinations by combining the modified keys, like SYM+Alt+key