mirror of
https://gitlab.com/mobian1/eg25-manager.git
synced 2025-08-29 15:22:20 +02:00
b21c4b0fa4
The PinePhone Pro uses the same EG25 modem as the OG PinePhone, but with a different SoC. It also uses an ALC5616 audio codec directly hooked up to the modem (which is I2S master in this case). The config is therefore almost identical to the PinePhone rev1.2 except for the gpios, UART port used and `AT+QDAI` config (to account for the different audio setup).
98 lines
4.2 KiB
TOML
98 lines
4.2 KiB
TOML
[manager]
|
|
# Delay between setting GPIO and PWRKEY sequence, set in microseconds
|
|
poweron_delay = 100000
|
|
|
|
# Uncomment the following if you need to change the modem detection timeout on
|
|
# resume and/or the time during which suspend is blocked after modem boot
|
|
#[suspend]
|
|
#boot_timeout = 120
|
|
#recovery_timeout = 9
|
|
|
|
[gpio]
|
|
chips = [ "gpio0", "gpio3" ]
|
|
dtr = { chip = 0, line = 3 }
|
|
pwrkey = { chip = 0, line = 13 }
|
|
reset = { chip = 1, line = 8 }
|
|
apready = { chip = 0, line = 12 }
|
|
disable = { chip = 0, line = 8 }
|
|
status = { chip = 1, line = 6 }
|
|
|
|
[at]
|
|
uart = "/dev/ttyS3"
|
|
configure = [
|
|
# Each command has 4 possible elements:
|
|
# * `cmd` : the AT command itself, which will be translated to "AT+`cmd`"
|
|
# * `subcmd`: the subcommand in case a single AT command can be used
|
|
# to change multiple parameters, such as QCFG (optional)
|
|
# * `value` : the commands, argument, usually used to set the value of
|
|
# a specific parameter (optional)
|
|
# * `expect`: the expected return value; the command is first executed
|
|
# without any value in order to query the current state. This
|
|
# state is then compared to the `expect` string; if they don't
|
|
# match, the command is then executed with value `expect` in
|
|
# order to set the parameter to the configured value (optional)
|
|
# A command can have `expect` OR `value` configured, but it shouldn't have both
|
|
# Print software version
|
|
{ cmd = "QGMR" },
|
|
# Configure audio
|
|
{ cmd = "QDAI", expect = "3,0,0,4,0,0,1,1" },
|
|
# RI signaling using physical RI pin
|
|
{ cmd = "QCFG", subcmd = "risignaltype", expect = "\"physical\"" },
|
|
# Enable VoLTE support
|
|
{ cmd = "QCFG", subcmd = "ims", expect = "1" },
|
|
# Enable APREADY for PP 1.2
|
|
{ cmd = "QCFG", subcmd = "apready", expect = "1,0,500" },
|
|
# URC configuration for PP 1.2 (APREADY pin connected):
|
|
# * RING URC: normal pulse length
|
|
# * Incoming SMS URC: default pulse length
|
|
# * Other URC: default length
|
|
# * Report URCs on all ports (serial and USB) for FOSS firmware
|
|
# * Reporting of URCs without any delay
|
|
# * Configure URC pin to UART Ring Indicator
|
|
{ cmd = "QCFG", subcmd = "urc/ri/ring", expect = "\"pulse\",120,1000,5000,\"off\",1" },
|
|
{ cmd = "QCFG", subcmd = "urc/ri/smsincoming", expect = "\"pulse\",120,1" },
|
|
{ cmd = "QCFG", subcmd = "urc/ri/other", expect = "\"off\",1,1" },
|
|
{ cmd = "QCFG", subcmd = "urc/delay", expect = "0" },
|
|
{ cmd = "QCFG", subcmd = "urc/cache", expect = "0" },
|
|
{ cmd = "QCFG", subcmd = "urc/ri/pin", expect = "uart_ri" },
|
|
{ cmd = "QURCCFG", subcmd = "urcport", expect = "\"all\"" },
|
|
# Allow sleeping for power saving
|
|
{ cmd = "QSCLK", value = "1" },
|
|
# GNSS configuration:
|
|
# * Enable A-GPS data upload support (XTRA)
|
|
# * Disable On-Demand-Positioning (ODP) mode
|
|
# to avoid running the GNSS system in the background, even when not enabled.
|
|
# * Enable Dynamic Power Optimizations (DPO) mode to turn off GNSS RF radios
|
|
# when they are not in use.
|
|
# * Only enable GPS and GLONASS, disable other GNSS systems.
|
|
# A-GPS data upload doesn't work for Galileo anyway.
|
|
# * Avoid turning on GNSS support automatically when the modem boots.
|
|
{ cmd = "QGPSXTRA", expect = "1" },
|
|
{ cmd = "QGPSCFG", subcmd = "gnssconfig", expect = "4" },
|
|
{ cmd = "QGPSCFG", subcmd = "odpcontrol", expect = "0" },
|
|
{ cmd = "QGPSCFG", subcmd = "dpoenable", expect = "1" },
|
|
{ cmd = "QGPSCFG", subcmd = "gpsnmeatype", expect = "31" },
|
|
{ cmd = "QGPSCFG", subcmd = "glonassnmeatype", expect = "7" },
|
|
{ cmd = "QGPSCFG", subcmd = "galileonmeatype", expect = "0" },
|
|
{ cmd = "QGPSCFG", subcmd = "beidounmeatype", expect = "0" },
|
|
{ cmd = "QGPSCFG", subcmd = "autogps", expect = "0" },
|
|
# Disable fast poweroff for stability
|
|
{ cmd = "QCFG", subcmd = "fast/poweroff", expect = "0" },
|
|
# Configure sleep and wake up pin levels to active low
|
|
{ cmd = "QCFG", subcmd = "sleepind/level", expect = "0" },
|
|
{ cmd = "QCFG", subcmd = "wakeupin/level", expect = "0,0" },
|
|
# Do not enter RAMDUMP mode, auto-reset instead
|
|
{ cmd = "QCFG", subcmd = "ApRstLevel", expect = "1" },
|
|
{ cmd = "QCFG", subcmd = "ModemRstLevel", expect = "1" },
|
|
]
|
|
suspend = [
|
|
]
|
|
resume = [
|
|
]
|
|
reset = [ { cmd = "CFUN", value = "1,1" } ]
|
|
|
|
[gnss]
|
|
enabled = true
|
|
url = "https://xtrapath4.izatcloud.net"
|
|
file = "xtra2.bin"
|